Search:

I'll have to work on that. My corel worked last time I used it that way. Oh, well GL everyone...

I am looking for a 39 x 25 or thereabouts. I have looked at Pcnc, EZ router, K2 and Cam-wood WR-203. Any suggestions would help. They are all within a $6000 - $8500. Price is really not as...

http://www.rockler.com/product.cfm?page=19441

This is the cheaper of any I have seen... They also have a pro model for around $3200.00


Good luck...
I am spending abt $10,000 for mine and my...

Looks like early South Bend Wood working lathe...

Still using the same setup. they want $1800 to upgrade to pci card and add the servo card, so I just swap the y axis when I am using my indexer. I will have to do something soon though because I...

Around 1979 Obama started college at Occidental in California . He is very open about his two years at Occidental, he tried all kinds of drugs and was wasting his time but, even though he had a...

Bring in the Fair tax.... Poor don't buy as much so pay less. Rich buy more so pay more tax... Think how much the tax is on a $3,000,000 boat at 26%.Get the fair tax book and you'll see that you...

I believe you must be an athiest. If I remember right Mr. Bill had a republican congress passing those bills that he signed to get the defecit down. Barney Frank and Chriss Dodd have blocked all of...

As a retired person and a conservative I believe we should have left Sadam alone and concentrated our efforts on Afganastan. Too late for those thoughts now, so I have to think about the future. I...

Try this...

I am a cuemaker and use plenty of tiny bits.... Get them at www.cuestik.com

www.cuestik.com

Try this....

Bimmer,
When I do long parts I use Vcarve also. I leave the part in one piece in the beginning and mark off however long I have on my table to work with. I then put guides every break point I...

Get VcarvePro and it does all that for you.....

Which model do you have and how much would you be asking...???

I also use Corel X3... You can Export instead of save and it does dxf for you....

Good luck

I have a sherline rotary table (indexer) and use it for cuemaking on my Techno isel 19 x 14 servo machine. I have the table mounted in the standup position and have added a handle for manual movement...

VCarvePro works the best of all. ttype fonts and single line fonts. Try the trial version and you'll buy it...

When I cut my parts I have made a baseplate with various t-nuts on the back side. I made a few aluminum straps bent to different shapes for different thicknesses of wood and clamp them down by a hole...

look into system3.com.

It may be that you have to import instead of open. I use corel and that's what I have to do....

I don't use (mm) but I cut most of my stuff with .0625 and if I need smaller I use .0313 fish tail end mills. Just can't get them to cut deep is the only thing. .125 is about the deepest I can cut...

I use a Techno Isel 4 axis and Vcarve Pro and/or PhotoCarve...

I don't think it matters what cad your using. It matters what your interface is set to or if it can handle CV. I have Techno equipment. I use servo motors tho and they have a CV mode if I choose to...

I have a Techno Isel Gantry system. I have a spare servo, but need the Amplifier card if anyone has a spare one lying around. I can get it from Techno, but of course am looking for cheaper than...

I also use Techno Isel and have Servos. Several things affect the jerking. I don't know if steppers are the same tho. I have a constant mode that I can use to cut. Depends on what interface you...

I have a techno servo gantry system. It uses the old ISA card and runs in dos.
1st question:
Should I upgrade to PCI and run in windows or stay in dos??
2nd question:
Techno wants $1800...

Your able to use laminate trimmers as an alternative. Depends on what speed you need and how much power. I have a Kress 800w motor and love it, except i'm in the usa and its a mm. Built my own bit...

I have not opened the computer yet, but according to the manual its a full slot isa card...also its an older compaq so I would assume full slot. I'm going to pull it tomorrow. The plug is 50 pin...