Because you have APC and APZ set to 0 it means you have incremental encoders using dog for deccelerating and finding the reference marker.
You can increase the limits ,make the reference zero and...
Type: Posts; User: zavateandu
Because you have APC and APZ set to 0 it means you have incremental encoders using dog for deccelerating and finding the reference marker.
You can increase the limits ,make the reference zero and...
what is the code of the spindle amplifier?
the tool setter is disabled by keeprelay and is done on PMC by manufacturer,you should have it on the book
APZ-1815 parameter
I checked like 5 backups from different machines and all have the 3201 like that so I assume is normal
Make the parameter 3201 as:
01000000
did the program enetred in CNC memory folder?
what software do you use to transfer programs?
can you show the parameter 3201?
thank you
on that window press the right + and go on untill you will find a menu called ONLINE
Check there if is in OFF STATE or NOT USE
Maybe you have the RS232 channel open in the I/O menu where you can connect online for the FAPT LADDER
PMCCNF->ONLINE
Is axis 3 the C axis?
What is axis 3?
in the parameters it seems that the 3 axis is using absolute encoders and not incremental
you need to go to the reference point if you know it and make the...
post the machine position screen when you overtravel and also post what you have in parameters 1815 and in 1320 1321
did you have a tool setter on the machine or the machine had one?The tool setter can block the machine go only in measuring direction
Also can you send a picture with the first diagnose page while...
if the zero return way is on + plus side ,you can increase the limit on paramater 1320 with 999999 ,move the axis in minus direction around 100mm,make the zero return and fater that put back the...
check in diagnose the G122.3 if it is really 0
i never heared in my entire carrier a Fanuc 0-M with aparametrs locked only if you have a hard key switch somewhere to block the PWE=1
Did the PWE is 1?
is the diagnostic binary or decimal format?...
M-Milling
T-Turning
L-Laser
P-Punch
G-Grinder
Fanuc released manuals for Laser and Punching and never for a grinder as the parameters and maintenance is similar to turning and milling
do you want to sell here?i think you are in wrong section
please post problems to help
why do we need them?
Try with the parameter 5003 bit 6 LVC or bit 7 TGC
LVC Offset value of tool offset
0 : Not cleared, but held by reset
1 : Cleared by reset
TGC Tool geometry compensation value
0 : Not...
First you can disconnect the power wires of the motor from the drive and start again the machine
If the alarm is still present,problem is in the drive
If the alarm is not present,the problem is in...
The brake is normally powered with 110v AC and on new machines is build in the motor with 24v DC
When the machine is off,the brake is not powered and hold the axis
When the main contactor MCC is...
yes,you need to atach the pmc file to be read
you can read it over ethernet if the machine has etehernet port
PS059-Program number not found
check the program again if it has the same numer inside of it as outside of name
when you go to IPL menu you just need to press enter for options you want to keep and change the value only for the option you need to change
look in PMC-DATA TABLE,where are the timers,counters,keeprelay
Try it in emergency mode state or go in PMC menu and stop the PMC
On the machine that you want to try the sram and is not loading all 4 files,did you tried to take out the sram?
Even if the machine is not starting you can take out the old sram to see if it is...
you did not attached any photo
When the MCC-main contactor is turned on ,the power supply gets power and turn 7 segment led to 0 and all servos are with "-" not blinking in normal state
so in your case i start looking of the...
As far as i know there is a servo software update also to be made for that new linear scale to work
what type of controller you have? 16i,18i,21i,30i,31i,etc?
what is the version and edition of...