Hi there
I've been around waterjet machines now for over 20 years and I can say that I have never come across one yet so can't comment on the quality of this machine, however I would definitely...
Type: Posts; User: neil76
Hi there
I've been around waterjet machines now for over 20 years and I can say that I have never come across one yet so can't comment on the quality of this machine, however I would definitely...
Hi
Check the pressure readings when you fire the pump through the dump valve, (pump only) do you still hold a steady pressure of 130PSI, or does this drop below 80PSI
Thanks
No problem, you can drop me a private message though CNC zone and the I could give you my email address, maybe we could then get the 32.2 set-up on your new pc
Cheers
Hi David
Take a look at your old pc, what version software are you running, as the latest version is not compatible with the 5 axis controller system, we may need to roll the software back, feel...
Hi
Ok no problem.
Did your old pc have a cable coming from the back going to a white plug? If so then this is the power supply for the USB controller, failing that you should have a separate...
Hi
What generation maxiem is this on, gen 1 or 2, which relay are you having issues with, is it the safety relay, can you send some pics
Cheers
Hi what year is your machine, take a look inside the back door of the computer control cabinet, does it have a black USB 5 axis controller attached to the top of the door. If so then this will only...
Hi Mhrothe
You can do your TXT as normal then draw the plaque around the TXT then autopath, you can check you part by clicking on render. Feel free to PM me and I can help further. Omax also has...
Thanks Brother
Happy Machining
Hi Mario
This make is not my expertise, but give WJS an email at [email protected] they may be able to give you some advice, it's a long shot but probably worth a try
Hi Karl
No problem, if you send me your email address via the private message I can send you over the the relevant schematic/ information on the USB power supply.
Thanks
Hi There Karl
This will run on a windows based PC but the system you have is called the 5 axis USB controller, this will only run on a 32Bit operating system.
the two cables from PC the black...
Hi Dan
Go to omax.com
And the create a user account, you will need the machine serial number for this.
You can then go to the customer dashboard , on there you will find lots off useful...
The cone and seat part are critical. We use tools from Alfi waterjet they sell a quality kit. When assembling your high pressure parts it's important to have a minimum off three threads showing after...
Hi there
Are the parts genuine Omax or copied acuustream parts?
Check the operation of the air actuator, this should move in and out smoothly when pressed in with you hand, if it is the older...
Hi there
Would it be possible to post your pictures, I can't seem to view them.thanks
Good morning
If memory serves me right, the boards are the same and they changed the part number because of the newest firmware, but I could be wrong.
If you do have the belt drive update then...
Hi there
I've also attached the load n go instructions and the correct dipp switch configuration, it looks like you have the gear drive from the previous attached pictures.
Many thanks
Hi there
You would require a load n go programming tool with the firmware installed to update the firmware.
Unfortunately with this type of card we are unable to hook up a laptop to read faults...
I feel you're pain $1600 each, I've never come across more than one faulty card at a time, it appears that the cards are enabled and ready to go.
No flashing LED = card's not enabled and not ready...
Hi there
I think Omax stopped using these motors and drives in early 2000, and they are now obsolete.
Unfortunately the latest motors they now use require different servo drives and a 9 axis...
Hi there
So let's try putting everything back to original positions, just double check that all the connections on the main board are going to the correct positions, especially if the bridge was...
Hi There
Sorry I was also supposed to say swap the cat 5 cable along with all the other connections.
In theory. If the card is a at fault you should get a Z axis fault.
What message does it show...
Hi there
One thing I would like to try before swapping the cards,
Swapp around the encoder plugs on the cards from Xf to Xr and Xr to Xf
This will check the feedback from the encoder to the...
Hi there
We could try and determine if the X1 control board is at fault by swapping it out for the Z card.
The Important thing for this is to note the position of the DIPP switches on the cards, ...
Do the errors reset if you press the black (reset button) on the pendant.
Thanks
Hi there
Do you have any spare cat5 cable's available just run them over the table to test. It's important to fully power down the table before making any swapps.
Thanks
Hi
Do the lights go red as soon as you power up and press reset are are they green for a few seconds.
On the controller card's we are looking for fast flashing lights.
The next thing I would...
Hi there
Is this a Gen 1 Maxiem or Gen 2.
If it's a Gen 1 then it won't have the gold servo card's, but it will have encoder extension cable's, the connections in the plugs can go bad on these....
Hi There
Sorry the servo card's are under the Red cover at the front of the bridge, remove the top plate and slide up the red cover with the Maxiem logo on, they are hidden behind here.
But if...