After memory crashing our Fanuc 0TB doesnt want to input parameters via RS232
I input all options and parameters #2, #38, #552 as usual
But when I push INPUT button LSK doesnt appear
With and...
Type: Posts; User: guhl
After memory crashing our Fanuc 0TB doesnt want to input parameters via RS232
I input all options and parameters #2, #38, #552 as usual
But when I push INPUT button LSK doesnt appear
With and...
After memory crashing our Fanuc 0TB doesnt want to input parameters via RS232
I input all options and parameters #2, #38, #552 as usual
But when I push INPUT button LSK doesnt appear
With and...
May be this will help
Looks like you should enter password into register 488 in diagnostic Mode.
2209 - ladder display mode
PWMs - signals for direct transistor bridge control
IRn, ISn - current feedback
MCON - contactor ON signal
DRDY - drive ready signal
Parameter 909#3 usually opens this option
At first check power supply on the MB
What about Flow control settings on PC? Try to change them
RS232 Communications | Fanuc 0i, 16i, 18i, 21i Series and 16/18 Models A, B and C | SharpCam Ltd
You should get "911 ram parity error".
Now you have to put in rs232 parameters by hand, then options by hand (or through rs232 pushing eob+input) and parameters.
Hope you backed up 900's...
If your spindle stops axis wil stop as well
https://www.kennametal.com/in/en/resources/engineering-calculators/miscellaneous/speed-and-feed.html
Take a photo of this message, please.
So why don't you use feed per revolution Mode (G95)?
May be your spindle encoder intended for rigid tapping?
If so, i'm not sure if it is coupled all the time.
Or you can observe real spindle speed during machining?
That is the manual
https://www.amazon.com/Fanuc-Operators-Manual-Appendixes-100/dp/B004THDH96
Early I found it on cncmanual.com for free
Then you should use spindle encoder and command feed per routine.
I would advise you take additional gauge with comparator, but where will you get reference? - because your cnc uses serial spindle...
SAR - is an output signal of spindle VFD and it must be procceded in ladder. Usually there is the M-command, which activates this function.
You should put it after SxxxM4(3) block
Look into wiring diaram on X21.4 signal and you will find out what can cause this alarm.
Along with emg button and limit switches this can be air pressure switch
As a rule, there is a button...
this must be in maintenance manual for your machine
should to be something like that
hello can you tell me how to do "I/O monitor write"?
I have 3 files with COM extension (non-linear compensation). Trying load them through TNCServer under 807667 password. TNCServer shows loading, then contence of file appears on TNC screen, I push...
here you are
I know only russian one KR580VV51A - it's the fully same except package (pin pitch is 2,5 mm instead of 2,54 mm), but I inserted this one into socket
check which signal turns on G127.5 coil in ladder
G127.5 means DNC mode for Fanuc
for 10 series - yes
can you check ladder? find the step, where M21 ativate MFIN function
can you change M21 action from open to close, may be your chuck is supposed to close when you input M21
check "chuck open" sensor
signal 8#7 (1st from the left) = 1 during M98 action?
look into diagnostic screen
hello have you managed to solve the problem?
what is instruction for barfeeder?
looks like the instruction for barfeeder calls macro which is absent
List of G-codes for 0TA series in attachment
You may find description in manual for 0TC or 0i series