Search:

Hi,
given that there is little happening at work on a Saturday I was able to turn the main isolator off and install a new three phase D curve circuit breaker and a three phase plus neutral socket...

Hi peteeng,



Easy to say, lets see how it actually works out in practice.

I can tell you from personal experience the advantages and disadvantages of a column design, and I don't have to...

Hi,
a moderately strong solution (5%-10%) of phosphoric acid. Paint it on, leave for an hour or so to dissolve the rust, and then thoroughly rinse it off.
This is the basis of quite a few of the...

Hi,



There we disagree, I am firmly in the camp of the more Z axis travel the better. In addition to the vice, workholding and the tool and tool holder, I always intended at some stage to have...

Hi peteeng,
if you were to use a slab of steel I would use it as the base rather than the walls. You could then mill T slots in it, T slots are just so damned useful. You'd probably want at least...

Hi Shane,
I use Delta servos on the basis of performance and cost.

There are cheaper Chinese made servos, and while I have no doubt they work, they have poor documentation, questionable backup...

Hi peteeng,
I follow your calculation but whom, in their right mind, would use a solid slab of steel 60mm thick? Were it a welded structure it could be made stiff and yet a lot lighter. Of course a...

Hi,
just received the oscillating pump from Auckland.

I was correct, the no back pressure flow rate is 1.4l per minute, not the 14 l per minute advertised.
The company whom supplied it supply...

Hi,
my 750W servos draw about 100mA from a 230VAC supply. Only when they have to supply torque do they start using current. My machine weighs 800 kg, so the X axis table weighs about 200kg.
The X...

Hi,
one thing that may influence your design is the use of concrete as a primary material. The most critical structure of a C column design is the column itself and the base. Both lend themselves...

Hi,
my reasoning goes something like this:

With a gantry and the Z axis at its fullest extent and the Z axis central in the gantry is the worst load condition. The gantry is under its worst...

Hi peteeng,
good work.

I might try something similar but with a regular column.

What does surprise me is in fact how similar they are. If this were are far as the design goes then as you say...

Hi,
that problem has been reported before. My understanding is that replacing the battery, while required, will not fix it. Critical data has been lost and needs be repopulated before it will run...

Hi,
why do you think it essential that you have encoder feedback for your spindle?

Is it position capable or something?

I use 750W Delta B2 servos, it was the first time I'd used AC servos so...

Hi Peter,
that spindle looks like the deal OK....and very competitively priced.

My own spindle is broadly very similar. It rated speed is 10,000rpm, so it has an S1 torque of 3.3Nm, which I think...

Hi peteeng,
I know you are wedded, or at least very much favour, high sidewalls and moving gantry designs whereas I favour C column designs.

What I do believe would be very instructive is to...

Hi,
I built a mill, that is to say a C column machine, hopefully rigid enough to cut steel, even if carefully. It weighs about 800kg. Its travels are 350mm x 350mm x 350mm.

Plenty of Z axis...

Hi peteng,
just scanning through the Hass PDF and it looks like a standard (BT40) VF1 is 3200kg while the VF6 breaks 9500kg. Both are still very heavy but not quite 11.5T either.

Craig

Hi,
yes the manufacturer does have a website. I did not buy off the manufacturer, I bought off Ebay from a guy in Vietnam. The spindle is new, but I would guess old stock. There is no exactly...

Hi,
OK, I would guess your estimate of the weight of the X and Y axis combo of 300kg is about right. That in turn suggests that your servo could hold it aloft without reduction. That would leave...

Hi,
you need to do the calculations, you are as you said electrically inclined not mechanically inclined.....me too as it turns out, but if you're going to do this then you
need to put numbers to...

Hi,
given the rapidity of the flow through the spindle I don't think that I really need a flow rate detector....but just something to confirm the flow.

I'm thinking of a wee cheat, cheap and...

Hi peteeng,
very true.

Your model does rather highlight the gantry as the 'weakest link' and that the gantry is also the least suited to casting in concrete/UHPC or whatever.

Like it or not I...

Hi peteeng,
1.8 tonne of steel for only 50N/um? I know this was only a rough 'sketch and analyse' for the purposes of discussion, but that is still a swag of steel for that result.

I believe...

Hi,
I use 750W Delta B2 servos on my mill. They are 2.4Nm (rated), 7.1Nm (overload), 3000rpm (rated). They are direct coupled to 32mm C5 BNFN double nut THK 5mm pitch ballscrews.
They can go up to...

Hi Peter,
I've just cleared my inbox.

Most certainly I'll get one for you, in fact I'm going to get another myself. They are good.

They are a capacitor run motor so you do have to wire them...

Hi,
my pump turned up, the Oriental Motor/Stainless Gear pump one. It's superb. I paid $46NZD plus $10NZD shipping from Napier, and yet I'd swear I'd pay $400USD or more for this thing new,
its...

Hi,
that's good news.

16mm wall sections are very much the exception here in New Zealand which make it a very expensive option to procure.

Craig

Hi,
the advantage of 16mm wall is that its thick enough that you can drill and tap with decent size bolts. 10mm or even 12mm wall does not really allow you to drill into the end
with anything but...

Hi peteeng,
yep, they look like a cost effective way to do things.

Craig