I'm a fanuc guy using a lot of custom macro. I got a new used okuma mill with osp 300 control and I'm trying to translate my fanuc macroB stuff to okuma. Here is a simple question : How to call a sub...
Type: Posts; User: samu
I'm a fanuc guy using a lot of custom macro. I got a new used okuma mill with osp 300 control and I'm trying to translate my fanuc macroB stuff to okuma. Here is a simple question : How to call a sub...
Same problem, control hung on not ready, LED of manual, auto and single mode are lit, cheked the main power supply, all voltage are good, checked the servo amp power suplpy, seems good. Reset led on...
alarm over 1000 are machine tool related, not fanuc and are different for each machine. Wath it seems to mean is that the spindle orientation limit switch is off when it should be on. Is this alarm...
It could have someting to do. There are some limit switch monitoring the state of the tool changer. According to their state, axis movement could be disable.
alarm over 1000 are machine tool related, not fanuc and are different for each machine. Wath it seems to mean is that the spindle orientation limit switch is off when it should be on. Is this alarm...
I recently bought an renishaw OMP40-2 probe with OTS tool setter and OMI-2t interface. I located the skip signal input and have M68/M69 m-code avaible since i have no chip convoyer. I think it missed...
the following is for umbrella type 20 tool automatic tool changer
diagnostic parameter:
N10300 P 11010000
N10301 P 00000111
N10302 P 01110001
N10303 P 10100110
N10304 P 00000000
N10305 P...
Similar issue, at power on, x and y axis "jump" in minus direction, then alarm 530, 531, 532 and sometimes 426 and/or 427 pop up. Even with the stop switch activated or the tool change switch to on...
I have a fanuc 0-MD ready for the 4th axis including 4th servo amplifier A06b-6079-h104. I do some reading and fourth axis does not seem to be plug and play. I don't really need full 4th ,indexer is...
You have to use different offset number for length and radius and if the offset is used with H word in program it is in Z(length) and with a D word it is in X-Y(radius). If you have 20 tool in your...
the answer is in the question: No cutter comp. So the center of a 1/2" endmill follow a path with a .5" radius. 1/4" radius of tool +1/2" toolpath radius= 3/4"
Heu.. i'm not sure i well understand wath you mean! Nobody program in machine coordinate!!! If so each time you do a set up, your part need to be exactly at the same point! No sense, usually all the...
I found that the parameter listed are not good for 0i. which model of 0i (0i model C or D)? it seems that 4028 and 4029 are ok for all 0i, i try some test on my old 0M-D with no luck, prm 6528 and...
sorry but i don't know so much about that, i thing that patern 1 limit the increase speed of the power while patern 2 increase the power at normal speed(like no power limitation). Idon't know if 0i...
maybe i'm wrong, but i suspect that you have a some confusion about wath G54 does. G54 X5. Y8. does not shift your origin. It just call a move to the point X5. Y8. in the workpiece coordinate system...
you can avoid incremental mode but it's a little bit tricky and in my opinion, much more complicated than use G91, there is a system variable that store current position in the workpiece coordinate...
This is exactly wath I've done in my previous post!!! Read the chapter 15 of your operator manual, there is evry thing you have to know about macro.
Before writting a macro, you have to know...
there is certainly a parameter in the 6000 range that set the overload limit, try to find it and maybe use a macro that set it with G10, at the beginning of any opération, set it at a limit that...
If i understand correctly, it's a Fanuc 0i mate control, so this kind of macro will work, if you have fanuc macro b otion turned on. to know it, try to run a small program like that:
%
O0001...
It seems clear that we are speaking of fanuc control here, and variable mapping for Fanuc is quite standar regardless of control model, some diference for system variable, but programming format is...
if operator need to change the code for each family of part, macro is the way to go!!! with macro you can create a thread milling cycle defined by surface, depth, x-y location of the hole cutter dia...
Maco could be a very usefull thing, i wrote several macro to repeat part, one to make a rectangular array of part, just ave to specify the x and y spacing, number of row and number of column. Another...
recently, when I power up my machine i got a lot of alarm, power supply alarm 01, spindle amplifier alarm 30 and alarm 414, 424, 434. but servo amplifier doesn't display any number. diagnostic prm...
it seems to me that your problem is more with the tool change thant with the zero return. Is your Z tool change is the same than the Z home? Also, you should have a switch activated at Z tool change...
level change i.e. pass from main to sub, sub to main or sub to another sub take a signifiant amount of time, also the use of "goto" statement is to avoid if you don't want to have a pause. The goto...
it is not a macro call but a sub program call, may be your delay is due to exit en re-enter in the sub program.
try to loop inside the macro instead of repeat the sub 25 time. Pass the number of...
once again, the point goes to Okuma for the service
we are going to buy a new VMC and at this time two machine are in the race. First one Mori seki Dura vertical 5100, second Okuma genos M-560-V. No experience with this two brand. We only cut...
Here is the finalist machine. First one Mori seki Dura vertical 5100, second Okuma genos M-560-V. No experience with this two brand. Here is the pro and con that I see for this two machine, hope you...
we are going to buy a new VMC and at this time two machine are in the race. First one Mori seki Dura vertical 5100, second Okuma genos M-560-V. No experience with this two brand. We only cut...