Hi f-bu,
we need ladder printout to diagnose an issue related to spindle fault and had done copy of plc eprom. Can you do it please.
here are attached bin files.
Type: Posts; User: wahidbashir
Hi f-bu,
we need ladder printout to diagnose an issue related to spindle fault and had done copy of plc eprom. Can you do it please.
here are attached bin files.
Thorja2009,
Thank you so much for sharing great info.This will indeed help me.
Best Regards
Hello to every one!
Got used machine Bridgeport VMC 1000 with Heidenhain 426/430 controller. Machine is getting its home position in all three axes. I made sample program in absolute mode and tested...
hello Members,
With FANUC 21i-MA control, my cnc mill has 4th axis jog button and ladder for this but not installed 4th axis. But cabinet shows that originally machine has 4th axis until we purchase...
Hello Members.
What settings are required to enable 4th axis on FANUC 21i-MA control ?
Parameter 1010 is set to 4.
How can i see fourth axis on screen ?
Help is appreciated.
TH Error comes while drip feeding moriseiki MV 35/40 ON 9600 Baud rate.
but it does not happen on 4800. Cable is sheilded and length is almost 5 feet.
Any idea to get rid if this ghost.
Thanks
Spindle drive on Bridgeport Interact 1 MK2 just not getting required RPM always. It takes more than one hour 2 have required RPM.
On measuring Field voltage, it is 170V DC.
Spindle drive is KTK....
Dear Dan Fritz,
A comprehensive detail about TV and TH error. I am facing problem about alarm at
9600 baud rate, 2 stop bits and even parity. but no problem on 2400 baud rate, 2 stop bits and even...
Dear All,
Having successfully running DNC to YASNAC MX1 with 2400 baud rate, even parity and two stop bits. When i change baud rate to 9600 on computer and machine, after some time there comes...
Hi All,
I have Moriseki MV-35 with YASNAC MX1 and unfortunately have to reload paramters again. Now machine is moving in handle mode but not going to zero return and gets overtravel. I also can not...
Could any one tell about boot problem of iTNC 530
Could not activate login daemon .
Any one how to install Heidnehain operating sytem into sys partition ?
Dear All,
I have installed a new CPU board JANCD-CPO3B in Mori Seiki MV 35/40.
On First power application display comes but after 10 seconds it disappeared.
On checking i have found that its...
Dear Dlservice,
While working to find the problem, i am now facing new problem before to test your advice. Now when i power on push button from operator panel then
numerical control contactor NCMX...
Dear,
Where it is located ?
Dear,
I have found thumb wheel switch from 0 to 9 and are labled as
The current setting is on switch # 0
0 system
1 parameter
2 check
3 load
4 test(0)
5 test(1)
Let me ask a question! What is coolant on/off option in TNC 407 on the keppad
as there is no sign of coolant control besides of M code
Dear dlservice:
First of all, I would like to thank you for kind reply. After a long time, some one has looked into my problem. My machine is still out of order.
I want to inquire where this...
We have this machine but nothing is happening when press power on button.
The control is MX1 YASNAC. Screen Is blank.
All power supplies are Ok. Machine is not over travel. The main cpu board is ...
Freinds,
I have a mori seiki mill with YASNAC control MX1(MV 35/40). When Power On Button is pressed then there is no display on the CRT. I have checked power supply and found 5V,12V and 24V are all...
Yes Dear,
With same results.
By the way what would you suggest if it is different on reverse
Just supposed it may be 18iT. If u have any idea then write it
Frndz,
I have a turning machine with FANUC 21i with serial spindle A06B-6112-H006.
Its commanded speed and actual displayed speed always differ by 20%.
measured speed is greater.
Is there any way...
Having a FANUC spindle drive with Power Automation CNC control ID #
A06B-6055-H103#H500.
Spindle drive has digital display as may be seen on the attachment.
Programmed RPM by M03 or M04 or do not...
Dear,
What is the way to do that. I just to want to make practice.
Hello,
Unfortunately, I lost parameters by suddenly down of SRAM battery.
I have NC parameters and ladder on floppy disk.
PCMCIA interface is out of order. But last time its RS232 interface was...
In which Fanuc manual, I can get memory card error list.
Friends,
I have three cards. I m able to use them as DNC on 2 machines. But the problem is that not able to take back up on fanuc 21i controls.
On power up machine and by pressing two right most...
Hi all,
Is there anyone to tell how to adjust commutation signals in ERN1387 rotary encoder to the seimens ac servo motor ?
This encoder has signals A,B,R ,C and D.
A and B are used for...
Forum,
I have Bridgeport VMC with 18i FANUC control. I want to initialize its tool data table. Tool capacity is 30. Tool changer arm has two mouths.
I want to define such as that my tool no 1 is...
Forum,
I have Bridgeport VMC with 18i FANUC control. I want to initialize its tool data table. Tool capacity is 30. Tool changer arm has two mouths.
I want to define such as that my tool no 1 is...