Search:

I used to have all kind of strange problems when doing selection and trying to get information from solids in edgecam.

Most of it went away when i got a workstation that has a certified graphics...

I'm guessing the motor would get hot if the bearing is faulty since it would be creating heat alongside the motor and running load of 20%
You should make a post over in haas lathe forum instead,...

Not sure but seems that this might be solved for us, or at least greatly improved.
Air amplifier that is part of the pallett retention was set to low from factory, (120 psi), according to what i...

Wye contactor seems to have been the problem, we have been running without any problems for a couple of weeks now.

Have the same problem with ours, if you figure something out i would like to know about it.

This is rework of some parts from our lathes, stickout is quite large. but i doubt it would have been a...

I do have access to a oscilloscope.
What would i be looking for ?

Haas tech wants to change the vector drive as a next step, i'm reluctant about throwing spareparts on the machine and figuring...

Had ours for 5 years, palletpool version.

chip evacuation from machining area is good but after that chips go everywhere except on the conveyor (we fixed this with sheetmetal,time and swearing)....

So, our EC400 from 2012 has an intermittent problem with spindle load.

We start it up in the morning and get 3-6% load on spindle starting it and letting the tool just rotate freely.
Then after a...

Might just be me but i suspect that over 300 users suspect that you have an abrasive personality, after your answer to simon.

I'll answer the same way you do.

Why don't you ask an edgecam...

I just hope you got a good post to go with your machine, be careful when running it on the machine in shop.
Also if you got edgecam from a liquidation didn't you get a server or a Cam station as...

That's everything there is, if you find more please report back.

Edgecam has very little material available for learning, courses are probably your best bet.
I don't do any 5-axis work, but i...

http://www.cnczone.com/forums/edgecam/114618-edgecam_best_tutorial_cd_video.html

Checking if anyone knows where i can source a replacement ACT pressure switch in Europe for our Multus.

The switch type is called CE615 and manufactured by ACT electric industry CO.LTD.

We sourced the replacement belt locally for the LT , cost was about 50 USD.

The other belt for the other machine was bought about 4 years ago so cant help there.
But was going through the bando...

Awesome, this will hopefully get me up and running much quicker. Thx a bunch.

One belt every 6 months :/. Kinda a hassle to disassemble and get to the belt. Must be a pain to do it that often.
...

So, one of our machines stopped today with an over travel alarm on lower turret X-axis.
After some disassembly I opened the hatch to check the belt that drives the screw for the x-axis. The belt...

You probably already fixed it but in the future the %programfiles% shortcut might work get rid of the problem.

So lets say you want to point to
c:\program files(x86)\edgecam

you write...

I believe this can be changed in the post through Code Wizard. Se attached picture.

If you have a post written outside of codewizard then you'll have to dig through your CXT or MXT file to find...

I have only done some simple PCI:s but I started reading a little and maybe you could use %Query together with %ASKDIGINFO or something similar to get information about the stock.

Your going to...

Not sure but this might be your problem

Roughing takes place within a boundary, so when edgecam complains that you have an open profile this means that theres a hole somewhere in your profile.
...

I have all the Edgecam CD:s, and they are very good. They wont teach you everything but they do cover most subjects.
Most importantly you start to understand the "Edgecam logic"

And also there...

Thank you :)

Hi,

We have an Mazak H400N where the machine covers on X-axis is a bit damaged. The machine sounds ok when running 50% rapid, but at 100% it's running a bit to fast for our liking.

Could...

I'm irritated with the outdated 3D interface. After using solidworks and then switching over to edgecam, I always think that they should improve/replace the 3d interface.
Things like moving parts...

Do you dislike mastercam or does it not do what you need it to?
Changing out a working Cam system for another system seems to me like you would be inviting problems :)

I don't know and don't use...

And to me it looks like the mod is calling me a cheater and is trolling a thread on the forum that he is moderating.

And no, it's for a fixture at work. The 500N force comes from using a high...

Thanks for all the help, i'll get back to this problem when i have time over.

Now that i know the problem of the problem it might go easier the next time around

Thx again

I've taken a look at the file you attached and have compared it to how I made my machine graphics for a 3axis machine.
The big difference is that I have "machine zero" (the coordinate system thats...

Ser inget fel i koden så där på rak arm men om jag inte minns fel så använder man inte ex: H10, har för mig det var en sån där sak som jag blev förvånad över på den mazak jag kör då och då.

Du kan...

Not sure if this is what you want, but try to use feature finder in design mode first. Then you can machine these features afterwards in manufacturing mode.

The other thing you could test is to...