ph-cleantec
Products
Clearly Clean Results
33
Safety and environment
Recycling plants
1000 SRE-EK Niederdruck-Heißreinigungsgerät + Entkeimung 95°C 7 bar
|
Separator for coolants and lubricants, pumps, filters, centrifuges
ph-cleantec GmbH
Separators for coolants and lubricants, pumps, filters, centrifuges
1000 SRE-EK
Application:
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for machine tools cleaning with your own cooling lubricant incl. cabin, magazine, spindle and gear room.
The SRE-EK is used for thermal desinfection especially of cooling lubricants. The lubricant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.
Advantages thermal desinfection:
• Without chemicals and without biocides
• In the bypass or. operated during running production, therefore no machine downtimes
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the cooling lubricant
• Higher occupational safety = lower sickness rates since no chemicals and no biocide
• Mobile, i.e. Can be easily transported from machine tool to machine tool
Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags
The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and oily soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests .
Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and changeable 600mm spray lance, hose connected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, temperature control.
Capacity desinfection : 6l/min. Capacity cleaning :1,8l/min. 7,5bar 10 KW, 16 Amp.
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for machine tools cleaning with your own cooling lubricant incl. cabin, magazine, spindle and gear room.
The SRE-EK is used for thermal desinfection especially of cooling lubricants. The lubricant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.
Advantages thermal desinfection:
• Without chemicals and without biocides
• In the bypass or. operated during running production, therefore no machine downtimes
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the cooling lubricant
• Higher occupational safety = lower sickness rates since no chemicals and no biocide
• Mobile, i.e. Can be easily transported from machine tool to machine tool
Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags
The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and oily soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests .
Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and changeable 600mm spray lance, hose connected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, temperature control.
Capacity desinfection : 6l/min. Capacity cleaning :1,8l/min. 7,5bar 10 KW, 16 Amp.
Disposal systems
1000 SRE-EK Low pressure hot cleaner Thermal desinfection 95°C 7 bar
|
Processing of coolant and lubricant
ph-cleantec GmbH
Processing of coolants and lubricants
1000 SRE-EK
Application:
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for cleaning machine tools with their own cooling lubricant incl. cabin, magazine, spindle and gear room.
The SRE-EK is used for thermal sterilization especially of cooling lubricants. The coolant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.
Advantages of sterilization:
• Without chemicals and without biocides
• Operated in bypass or operated during ongoing production, therefore no machine downtime
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the coolant
• Higher occupational safety = lower sickness rates since no chemicals and no biocides
• Mobile, i.e.h. Can be easily transported from machine tool to machine tool
Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags
The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and öly soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests.
Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and replaceable 600mm spray lance, hose üconnected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, Temperature control.
Capacity desinfection: 6l/min. Cleaning:1.8l/min. 7,5bar .10 KW, 16 Amp.
Machine cleaning especially for greasy, oily and complex surfaces.
Ideal for cleaning machine tools with their own cooling lubricant incl. cabin, magazine, spindle and gear room.
The SRE-EK is used for thermal sterilization especially of cooling lubricants. The coolant from the tank of the machine tool is sucked in, thermally sterilized and returned to the machine tool. This can extend the life of the coolant and reduce the cost of the coolant and its disposal. The less frequent replacement of coolant or the disinfection in the bypass also means that the machine tools are at a standstill less often. Above all, biocides can be dispensed with, thus increasing occupational safety and reducing sick leave.
The device is mobile and can therefore be transported from machine tool to machine tool.
Advantages of sterilization:
• Without chemicals and without biocides
• Operated in bypass or operated during ongoing production, therefore no machine downtime
• Longer service life of the cooling lubricant = considerable savings for purchase and disposal of the coolant
• Higher occupational safety = lower sickness rates since no chemicals and no biocides
• Mobile, i.e.h. Can be easily transported from machine tool to machine tool
Advantages cleaning:
• Significant time savings of idR 80-90%
• Self-sufficient: Thanks to the 60-l tank independent of permanent supply of cleaning medium
• Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
• Significantly lower costs than manual cleaning with rags
The operating principle is based on the high temperature combined with low pressure: At 95°C, greasy and öly soils dissolve quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces up to deep sack holes and cavities can be cleaned without any problems and without any rests.
Technical data:
Drivable. Without collector for parts cleaning. With three heating elements.
5m hose with lance gun and replaceable 600mm spray lance, hose üconnected to the device via a quick-change coupling. Start/stop operation üvia the gun. Stepless pressure adjustment.
Water and medium supply without pre-pressure from 60l tank, 5l tank with dosing device for cleaning concentrate, water shortage shutdown, Temperature control.
Capacity desinfection: 6l/min. Cleaning:1.8l/min. 7,5bar .10 KW, 16 Amp.
Thermo EK Thermal desinfection of cooling lubricants
|
Processing of coolant and lubricant
ph-cleantec GmbH
Processing of coolants and lubricants
Thermodes 5
Application:
The Thermo-EK is used for the thermal disinfection of cooling lubricants. The coolant from the machine tool tank is sucked in, thermally sterilized and returned to the machine tool. This can extend the service life of the coolant and reduce the cost of the coolant and its removal. The less frequent replacement of coolant and the disinfection in the bypass also reduces the downtime of the molds. Above all, biocides can be dispensed with, thus increasing work safety and reducing sickness.
The equipment is mobile and can therefore be transferred from tool to tool.
Advantages:
• Without chemicals and without biocides
• In bypass or. operated during ongoing production, therefore no machine downtime
• Längere life of the cooling lubricant = considerable savings für purchase and disposal of the KSS
• Höhere occupational safety = lower Krankenstände since without chemistry and without biocide
• Mobile, ie.i.e. can be easily transported from machine tool to machine tool
Technical data:
Mobile, in compact design, without tank. Allows suction and thermal sterilization of liquids from separate tank. Filtration with active filter monitoring, adjustable monitoring of the bath temperature on the suction side, 5m suction and return hoses.
Equipment output approx. 5l/min, 5 KW, consumption approx. 4 KW due to heat recovery.
Weight : 55 kg
The Thermo-EK is used for the thermal disinfection of cooling lubricants. The coolant from the machine tool tank is sucked in, thermally sterilized and returned to the machine tool. This can extend the service life of the coolant and reduce the cost of the coolant and its removal. The less frequent replacement of coolant and the disinfection in the bypass also reduces the downtime of the molds. Above all, biocides can be dispensed with, thus increasing work safety and reducing sickness.
The equipment is mobile and can therefore be transferred from tool to tool.
Advantages:
• Without chemicals and without biocides
• In bypass or. operated during ongoing production, therefore no machine downtime
• Längere life of the cooling lubricant = considerable savings für purchase and disposal of the KSS
• Höhere occupational safety = lower Krankenstände since without chemistry and without biocide
• Mobile, ie.i.e. can be easily transported from machine tool to machine tool
Technical data:
Mobile, in compact design, without tank. Allows suction and thermal sterilization of liquids from separate tank. Filtration with active filter monitoring, adjustable monitoring of the bath temperature on the suction side, 5m suction and return hoses.
Equipment output approx. 5l/min, 5 KW, consumption approx. 4 KW due to heat recovery.
Weight : 55 kg
