[Highfly]

Hi All

Hoping someone has seen this and can help.

Machine is a Yang SMV 1000 with a Fanuc 0-MD

I have a 1007 alarm wdescriptionpotion of "Mag CT1 NE Ct2"
The Alarm resettablesetable.

I found some info on the net saying check diagnostic 455 and make it the same as Diag 457. I had 0001 in 455 and 0000 in 457 so changed it to match.
Fanuc is saying this is a Yang Alarm. I cant find any alarm info on the net and cant find anyone at Yang that will return my calls.
Alarm is related to the auto tool change system (ATC Red LED is lite)

Brent

[EricMFG]

I had a Yang SMV1000 for a little while I had the same exact problem. Also the tool changer would get stuck in mid change or the tool magazine wouldn’t retract. If I remember there are three parameters you need to look at. One displays the current tool pot. You need to change one of the 455 or 457 to one less or one more than the current pot number. I’m not sure If I still have the notes on how to fix it I can look.

I got tired of trying to re-align tool pots to correspond with what the NC so I would set the parameter to one higher call up T1 then reload the tool changer. If you do that I would recommend clearing height offsets that are not used.

[EricMFG]

I had a Yang SMV1000 for a little while I had the same exact problem. Also the tool changer would get stuck in mid change or the tool magazine wouldn’t retract. If I remember there are three parameters you need to look at. One displays the current tool pot. You need to change one of the 455 or 457 to one less or one more than the current pot number. I’m not sure If I still have the notes on how to fix it I can look.

I got tired of trying to re-align tool pots to correspond with the NC so I would set the parameter to one higher call up T1 then reload the tool changer. If you do that I would recommend clearing height offsets that are not used.

You can write a quick program to load or unload the tools something like
M6 T1;
M00;
M6 T2;
M00

[Highfly]

Thank you,

I would be very thankful if you would check your notes. I'm not having any luck finding support for this machine.

The machine wont allow me to do anything at all with the alarm up so cant try the program yet.

[rwazana]

did you do a zero return to the mag?

[Highfly]

Nothing will move with the alarm on, cant move anything.

[cncts11]

Definitely machine side alarm...most machine builders use a "dual counter" method like this (for instance, older Leadwell lathes use this to make sure the turret position coincides with the actual position). If it continues to occur, then you need to look at a mechanical issue, or the method of detection, etc. because something is causing the mismatch (like a switch miscount for instance). If you set the parameters to match the actual then it should reset the alarm; however, if you need to set the parameters to be one less or one more as EricMFG is suggesting may be the case, then that would have to happen otherwise the alarm won't reset because it would still be technically in a mismatch condition.

[Highfly]

I've spun the tool holder manually. It was on tool 4, was supposed to be going to 1. I've played with the parameters, actually the Diagnostics but am unsure what it wants to see. I'll keep playing with it. Thank you very much for the response.

[EricMFG]

Apologies for my delayed response I’m still hunting around. I originally purchased a couple of CNC’s and a bunch of other equipment also took over the shop lease from a company that went under. So when the Yang was sold and I palletized all the other companies paper work and left over parts they made. So now I’m looking threw the pile to find the notes. Did you happen to buy the machine from a guy in Massachusetts? If you did a copy of the notes are in one of the manuals and It’s a hand written. If I have no luck Fanuc has impeccable support and offers support on their controls for 20 years after it was manufactured.

[Highfly]

No worries Eric. Machine was bought in Canada. I tried Fanuc and the alarm is on the machine side not Fanuc side so that was the end of the support :-(

[EricMFG]

No worries Eric. Machine was bought in Canada. I tried Fanuc and the alarm is on the machine side not Fanuc side so that was the end of the support :-(

I sent an email to the guy who serviced and programmed the Yang before I bought it he works for Methods Machine. The Yang I had was part of the buyout but I had too many problems with the tool change so it's gone.

1. The tool magazine would get stuck in between pots.
2. Sometimes the magazine would not retract the spindle head would get stuck in the up position. (You would have to enter the tool change sequence in MDI mode. Something like M86 then another M code to move the magazine then another M code to end the tool change sequence) Or push the button on top of the solenoid on the back of the machine, only do that when the NC is OFF.
3. The NC would lose track of the pot numbers. (think it's a problem with the encoder not the NC)

[EricMFG]

I sent an email to the guy who serviced and programmed the Yang before I bought it he works for Methods Machine. The Yang I had was part of the buyout but I had too many problems with the tool change so it's gone.

1. The tool magazine would get stuck in between pots.
2. Sometimes the magazine would not retract the spindle head would get stuck in the up position. (You would have to enter the tool change sequence in MDI mode. Something like M86 then another M code to move the magazine then another M code to end the tool change sequence) Or push the button on top of the solenoid on the back of the machine, only do that when the NC is OFF.
3. The NC would lose track of the pot numbers. (think it's a problem with the encoder not the NC)

Have a look at parameter 500 for some reason it's coming to mind. I remember paging up to a higher parameter number then 455 and 457. Whatever the higher parameter was, 455 or 457 has to be one number higher or lower that will clear the alarm.

[Highfly]

COOL!!! thx.

455 was 1 and 457 was 0
I looked at 500 and was messing around with it. It was either 1 or 2 cant remember now.
So 500 has to be one number higher than 455 and 457?
I found on line that 455 and 457 should match, in my case they did not.

Thx again, really appreciate your help!

[Highfly]

Can I ask you what you have in D455?

[samu]

D455=19 and it never change.

[Highfly]

THX

[Highfly]

I'm so close to having this thing fixed......
I have the Rotary table problem figured out. A wire was sitting on the bottom of the control that was supposed to be hooked into pin 25 of the M20 plug on the Fanuc I/O board. The Rotary table now responds to the speed switch and will spin fast and slow but it still wont trigger the Deceleration Switch (X19 bit 5).

I found another wire on the bottom of the control that looks like it was stuck on the M20 pins as well. It's a grounded jumper. Two wires are hooked together and then go to ground. Can anyone that has a Yang with a rotary table please have a look at the M20 plug on the I/O Board and see if you have any wires attached to it. I know pins 4,20,25,29,39,and 40 are all Rotary table related but don't have a clue where this jumper could tie into.I am confident it goes somewhere on the M20 slot. Fanuc doesn't have a clue. I see nothing in the electrical schematic that I have other than the pin 25. This machine just has a mickey mouse set up where they are pushing the wire right onto the pin, doesn't have a proper Honda style plug into the I/O board.