[FlyGuy007]

I ordered a LC6090 80w laser from Jack at WKLasers and it arrived last week. The shipping was prompt and it arrived in Canada just as Jack said it would. The Freight forwarder used in Canada was lacking to say the least but a few words from Jack at WKLasers and things seemed to move along nicely.

I picked the laser up in Halifax and took it home and uncrated it. The crate was top notch and the packing was better than I could ever have expected. The general build of the machine is also better than i could have hoped. The body of the machine is very well built, its a heavy guage steel and is several times thicker and heavier than I expected. Everything looks well made . My only gripe with the build is that many of the bolt holes are drilled and tapped and odd angles, so its obviously done by hand. Many have holes in one side of the machine but not the other so no bolt was placed at those location. But there is probably more screws than are needed anyway. I saw about a dozen of these instances where hardware was installed. And a few lock washers would have been nice as alot of the hardware just wasn't tight.

The instructions are pretty much nonsense. The translation is poor and its very difficult to understand the idea trying to be conveyed in many of the sentences. Just a jumble of English words tossed into a sentence. But the video plus the instructions make it doable for someone who is on the ball.

The PCI driver card that came with the machine (MPC03) is a nightmare. Its quaility appears low and I tried four computers before I found oe it would even boot in. In the first two cases with the card installe dthe compuetrs would not even POST, just a dead computer. Worked fine with the MPC03 though. The computer I am now using boots most of the time with the card in it but gives various errors at times, and after 5 or 6 boots becomes unusable. Removing the card and rebooting a few times fixes all the errors and I reinsert that card and start over :-) There has to be a better system that the MPC03 card.

The software is hard to use and the install is not well documented. But after I installed anything that looked like an .exe the system booted OK. Much of the install is in Chinese though so some guesing at which button to click was encoutered several times.

I ordered alot of extra parts and (mirrors, lens, drivers and an extra tube) which is a good thing as I suspect the first tube I installed is bad. But I am not sure enough to risk changing it out until I have heard from Jack as I don't want to do that only to find I missed something simple.

Anyway overall I am impressed and I think it was a great deal. Now if Jack helps me like I think he will it will be a super deal.

I'll keep you all posted!

Mike Purcell

[wklaser]

Hi Mike Purcell,
I have sent you many emails but all of them are returned to me marked failure notice, I wonder if you have received my email. Please reply to me

[email protected] or [email protected]

thanks

JackYin

[FlyGuy007]

Jack;

I have not received any except one 2 days ago asking if I received the laser. I will resend my emails to you.

Thanks
Mike Purcell

[FlyGuy007]

Well here's an update.

I have the laser making pinholes on the test and I can even cut a circle etc using the supplied software.

I have had nightmares with the controller card included with the system (MPC03) It just seems like 3 of the 4 computers I have at the house will not work with the card. It appears from here that its an IRQ issue. Two of the 4 computers are completely lifeless with the controller card installed. One is so flakey that it just won't stay running. The last one boots now about 80% of the time but gives random and varied issues (POST errors, CMOS errors, random detection of new hardware etc) But its at least working.

The reason I bought the laser was that it can cut corel files but so far I can't use the corel files I have. In fact it will not recognize Corel X3 at all and wants my system to have much older versions of Corel on the system before it will even install the drivers. I am currently trying to find an older version so I can continue to try it out.

So far I like the system, it appears well made, not USA well made but not bad and certainly a great deal for the price. But there is alot of setup involved and still many things I have not yet ironed out. For example the cutting table is supposed to move up and down but I can't see how and my water chiller actually seems to warm the water. But I am making progress and the company has been good so far.

Thanks
Mike

[KTP]

So how cheap does something have to be to be a "good deal" even if it doesn't work?

I was thinking of coming out with a new car design, modeled on a Lexus, but for about 1/5 the price. It wouldn't actually run or anything, but do you think people would buy it because the price made it a really good deal? Just seeking opinions...

[FlyGuy007]

You know I guess it depends on the type of person you are. If you decide you want to learn to fly, you can buy yourself an almost finished airplane kit and tweak it yourself for as little as a few thousand or you could buy a brand new Boeing 737 for 40 million. Easy choice for me.

I am a bit of a tinkerer and bought the laser mostly because I needed it but also because its a toy. Yes, I could have paid and I am not exaggerating here 17x more for a finished model like an equivalent Epilog here in Canada. So even if I spend weeks getting this operating right, or even months I will have saved well over 50K and had fun and yes a few frustrations doing so. That's part of the enjoyment of it.

If you have a business that needs it quick and needs support right now then I'd stay clear. If you don't have spares tens of thousands falling out of your pockets then I'd go the way I did. For support, Jack has been good, in fact as good as some North American companies I have dealt with. Truth is, when I write to ask a support type question I have usually figured it out by the time he gets back to me.

I think the laser is basically well built and I'd say in many cases works fine, its the language issue that I think is the real problem as the instructions just are not up to the standards we have come to expect in North America. But the info is there and after you get it to work I have gone back and said to myself that well, maybe that's what the instructions meant..... :-)

I have no doubt I'll get it working and in the end I'll be a much better end user than if someone had of airlifted in a shiny gold plated Epilog and held my hand for the entire first month.

How many of us here that own CNC machines bought a $250K mill and how many of us turned to the Shopbot, shopSabre style systems that allow us to get in there and tinker without costing us the price of a house.

I could never have come close to owning a new Epilog or General period.

Mike

[channel7]

So how cheap does something have to be to be a "good deal" even if it doesn't work?

I was thinking of coming out with a new car design, modeled on a Lexus, but for about 1/5 the price. It wouldn't actually run or anything, but do you think people would buy it because the price made it a really good deal? Just seeking opinions...

I am in agreement with this perspective more than the view of getting the most parts for the lowest buck and finishing the engineering yourself once it arrives.

Maybe that is one of the lines that will separate a hobbyist from a guy trying to make a living off what the machine can produce. I keep thinking that MY time is the most expensive component in this equation. I will waste enough of that time doing research trying to find the laser that will best serve my needs. I certainly don't see it being beneficial to spend an additional month once the machine arrives trying to get it to cut something correctly.

I do see your perspective, FlyGuy, I do. You chose to invest the time and not the capital. I am very interested in these 'Made in China' lasers but reading the posts here for so long I still haven't found the purchasing experience that has been a smooth one. The software is so critical yet it seems to be frustrating to use. That is the major turn-off for me at this point, the software adds unnecessary labor costs.

Please continue to post your experiences, FlyGuy!! It helps me to see how the machines are built, the support structure surrounding them, and the ease of using the packaged software. Your story, and many like it, helps a lot of us reading the posts here.

[wklaser]

Hi Mike,
I am pretty glad to hear that you are happy with the machine, last time I send the DSP4.0 to you, now please log on your Skype I would like to send the new DSP5.0 to you, then you can use the one you prefer

Thanks again for your comments.

PS: Anybody who wanna buy laser enrgaveing cutting machine, please feel free to contact me:

email:[email protected]

men:[email protected]


Jack Yin

[isasuleahmed]

Jack,
Can I use your software (DSP5.0) to upgrade my laser (IE1200 laser with 80W)? I got it from 'INK EXPRESS' in december 2005 and yet to be install.

Isa

Hi Mike,
I am pretty glad to hear that you are happy with the machine, last time I send the DSP4.0 to you, now please log on your Skype I would like to send the new DSP5.0 to you, then you can use the one you prefer

Thanks again for your comments.

PS: Anybody who wanna buy laser enrgaveing cutting machine, please feel free to contact me:

email:[email protected]

men:[email protected]


Jack Yin

[wklaser]

Jack,
Can I use your software (DSP5.0) to upgrade my laser (IE1200 laser with 80W)? I got it from 'INK EXPRESS' in december 2005 and yet to be install.

Isa

Hi ISA,
Yes you can use our DSP5.0 to uograde your LC1280(IE1200), if you have questions, feel free to to let me know by [email protected], [email protected]


JackYin

:rainfro:

[wklaser]

Hi Mike,
Can you log on your MSn or Skype agine? I did receive your message that day but I always failed to send message to u by msn that day.

[Laser Doctor]

I ordered a LC6090 80w laser from Jack at WKLasers and it arrived last week. The shipping was prompt and it arrived in Canada just as Jack said it would. The Freight forwarder used in Canada was lacking to say the least but a few words from Jack at WKLasers and things seemed to move along nicely.

I picked the laser up in Halifax and took it home and uncrated it. The crate was top notch and the packing was better than I could ever have expected. The general build of the machine is also better than i could have hoped. The body of the machine is very well built, its a heavy guage steel and is several times thicker and heavier than I expected. Everything looks well made . My only gripe with the build is that many of the bolt holes are drilled and tapped and odd angles, so its obviously done by hand. Many have holes in one side of the machine but not the other so no bolt was placed at those location. But there is probably more screws than are needed anyway. I saw about a dozen of these instances where hardware was installed. And a few lock washers would have been nice as alot of the hardware just wasn't tight.

The instructions are pretty much nonsense. The translation is poor and its very difficult to understand the idea trying to be conveyed in many of the sentences. Just a jumble of English words tossed into a sentence. But the video plus the instructions make it doable for someone who is on the ball.

The PCI driver card that came with the machine (MPC03) is a nightmare. Its quaility appears low and I tried four computers before I found oe it would even boot in. In the first two cases with the card installe dthe compuetrs would not even POST, just a dead computer. Worked fine with the MPC03 though. The computer I am now using boots most of the time with the card in it but gives various errors at times, and after 5 or 6 boots becomes unusable. Removing the card and rebooting a few times fixes all the errors and I reinsert that card and start over :-) There has to be a better system that the MPC03 card.

The software is hard to use and the install is not well documented. But after I installed anything that looked like an .exe the system booted OK. Much of the install is in Chinese though so some guesing at which button to click was encoutered several times.

I ordered alot of extra parts and (mirrors, lens, drivers and an extra tube) which is a good thing as I suspect the first tube I installed is bad. But I am not sure enough to risk changing it out until I have heard from Jack as I don't want to do that only to find I missed something simple.

Anyway overall I am impressed and I think it was a great deal. Now if Jack helps me like I think he will it will be a super deal.

I'll keep you all posted!

Mike Purcell

You say the instructions are a nonsense. The PCI card is a nightmare. Quality is low. Computers don't work with the system.Video doesn't live up to expectations. Software is hard to install and use. You purchased alot of extra parts. -And your impressed with it. My feeling is you are going to experience many troubles with this unit and you will end up replacing it within one-year. Please keep me posted.

Thank you.

The Laser Doctor

[dragoneye]

I have 3 of WKs lasers and am just about to complete the set with a LG900.

AND I HAVE NEVER HAD ANY TROUBLE WITH THE TUBES and if you bear in mind that there are thousands of these machines comming out of china i feel that although it is personal to a person that has a bad machine on percentages it is probally very low.

Also we dont hear about North American machines that have faults is due to the fact that A they dont want anyone to know that there peice of junk that cost 5 times as much is faulty and B look close and see just what is manufactered in china.

Most large companies state made in their country when they take their chineese parts out of their bonded stores and put together in the country of origin allowing them to fool the public with standards of their country and any one who thinks not needs to check this out before commenting as we all know china is supplying 90% of all goods in the world today.

So stop comparing all chineese as bad they are not .

I understood that this site was to help each other buyers and sellers alike but all i seem to see is one way traffic aimed at the seller who is improving his products all the time with R & D for example take WKlasers machine of a year ago and look at the build and software today,they listen and improve all the time.

So please keep on posting experiances GOOD & BAD so we can all learn from it AND sellers keep posting your machines so we can see the improvements BUT how about those who have no machine and express their veiws on others misfortunes keep their big mouths SHUT until they actaully have their own experiance to comment on good or bad.

[FlyGuy007]

Questions and Answers about WKLaser and my experiences with my laser.

Hey Mike;

I am currently looking at your website with those lovely pictures of what looks like plastic silk screen prints ready to profile cut.
I understand it is a 100watt model from WKLaser...

Firstly I am in the UK and keen to buy a laser but quite attracted to it for price etc. Can I ask a few questions about your machine as I am a little uncofrtable about ordering from China.

1: How long did you wait? I am getting the impression that these lasers are built to order, but when we see factory pictures we seen production lines. Did you use Fedex to import?

2: I have loads of acyrlic to cut, mainly 3mm clear and red, how long does it take to cut saw 300x150mm rectangle? How are the edges, are they verticle and tidy?

3: Have you replaced the tube yet? or lenses?

4: I understand the PCI driver board is poor, is the purpose of this board to communicate with drives? I understand you had POST problems, do you daily struggle with this? I am wondering if you had a dodgy board or it is a poor design?

5: Engraving, is it really any good compared to an expensive machine? I am thinking about engraving laminates and just simple stuff, I can see from some images I have seen that the engraving isn't that good, do you agree?

I would appreciate any advise before diving in as I have been speaking with both WKLaser and Rabbit Laser which seems to be the same product.

My email is [email protected]
www.everysign.co.uk

regards
Dave[/QUOTE]

Hey Dave;

I'm quite happy with it despite some initial setups issues. I'll answer your questions in order.

1. I ordered and paid for the machine about 2 weeks before it shipped. Now I know it has to be trucked to the port and wait for a container ship heading for Canada to load and leave so I think it was reasonable. It took about a week to arrive and was in a heavy wooden crate and well packed. No worries there.

2. The edges are just about perfect, I cut .68 acrylic and PETG (.60mm) The little compressor that comes with it to keep the laser clear is a little anemic so I'd buy two of them and t them together or just use a bigger compressor. More air seems to improve the cut speed and quality by a good margin. It cut fine until I tried more air then it cut great! Decent pics at http://classicplayfields.com/photo14.html
However, these are real close and don't really do the cuts justice, they look even better!

3. I have about 90 hrs of cut time on the machine now and am still on the original tube. Use distilled water as they specify as my tube is a bit dirty inside from me using well water and having the minerals settle out. Still seems to work fine though.

4. The PCI card is junk, cheap Chinese make. However, I think the problem in my case was the PnP feature on the card just did not work, so when the computer assigned an interrupt to the card like its supposed to the card would not accept it and conflict with something else in the system. I tried different PCI slots in 3 different computers until it works. So I think it was just a faulty card. Works fine now though, but frustrating to set up.

5. I have engraved only 1/4" MDF so far and I'd say that it was super. It cuts very clean edges and at full power will engrave almost half way through the MDF. I have full confidence it will do anything fine.

Jack Yin at WKLaser was very good to deal with as I said before he was much better than I could have hoped for.

Thanks
Mike

[wklaser]

Questions and Answers about WKLaser and my experiences with my laser.


Hey Dave;

I'm quite happy with it despite some initial setups issues. I'll answer your questions in order.

1. I ordered and paid for the machine about 2 weeks before it shipped. Now I know it has to be trucked to the port and wait for a container ship heading for Canada to load and leave so I think it was reasonable. It took about a week to arrive and was in a heavy wooden crate and well packed. No worries there.

2. The edges are just about perfect, I cut .68 acrylic and PETG (.60mm) The little compressor that comes with it to keep the laser clear is a little anemic so I'd buy two of them and t them together or just use a bigger compressor. More air seems to improve the cut speed and quality by a good margin. It cut fine until I tried more air then it cut great! Decent pics at http://classicplayfields.com/photo14.html
However, these are real close and don't really do the cuts justice, they look even better!

3. I have about 90 hrs of cut time on the machine now and am still on the original tube. Use distilled water as they specify as my tube is a bit dirty inside from me using well water and having the minerals settle out. Still seems to work fine though.

4. The PCI card is junk, cheap Chinese make. However, I think the problem in my case was the PnP feature on the card just did not work, so when the computer assigned an interrupt to the card like its supposed to the card would not accept it and conflict with something else in the system. I tried different PCI slots in 3 different computers until it works. So I think it was just a faulty card. Works fine now though, but frustrating to set up.

5. I have engraved only 1/4" MDF so far and I'd say that it was super. It cuts very clean edges and at full power will engrave almost half way through the MDF. I have full confidence it will do anything fine.

Jack Yin at WKLaser was very good to deal with as I said before he was much better than I could have hoped for.

Thanks
Mike

Hi Mike,
Thanks again for your high comments on our lasers, and on me.. .. Hope you still enjoy your lasers now. If you have any questions, don't hestiated to let me know..

Anybody who wanna lasers with low cost, good quality and personzlied after sale service, don't hestiated to email to me. I would like to show the evdience for you that not all chinese products are Junk.

My email address is [email protected], [email protected]


JackYin

:rainfro: :rainfro: :rainfro: :rainfro: :rainfro: :rainfro: :rainfro:

[lamicron]

I'm from Colombia, Southamerica, a year ago I bougth a laser machine from china, it is true this people dont explain a little thing about all the trouble you will get but you can get a far away price compared to an epilog or universal machine, I know both.
But after a week trying we found the way to put it to work. Now I have a very fast machine , doing the same work as an epilog for 1/5 of the price, every 8 months i have to change the cheap tube ($300) some times it could last less time but still is far away good bussiness for me. I know about the quality of the american products but here we are working with a little cnc table. Its a very simple machine, now I know about it, I sold other 2 machines for other customers and only take 2 days to put it to work, still the same bad comunication with china, they dont test the machines prior to sending, allways you have to figth with the PCI card, and now also know that you can work with garbage PC's, better if you use 1 gb ram in a almost new generation PC.
So, yes, its a good bussiness, for the same money of one epilog mediumsize I bougth 3 huge size machines and have some left for other one.

Luis

[pedroman]

I have several friends in the Detroit area and they all complain about the same issue concerning the economic status of the area. Our US automakers have gone down hill so fast that Detroit and surrounding areas have created the greatest number of home forclosures than anywhere else in the US. From a recent article http://www.msnbc.msn.com/id/13086712/
"On average nationally, there are 29 houses in foreclosure for every 100,000 U.S. residents. But at the top of Foreclosure.com’s list, in hard-up cities like Cleveland and Detroit, the rate is several times that. "

The economy is tough there. I would suggest that you look in the south like Raleigh North Carolina, Austin Texas or similar areas. More recession proof because of reliance on more than one industry.

Good luck

Pete

[ArturoV]

I was wondering if you have had any problems with your Laser Cutter.
I just got a 80W HX1290SE at its not collaborating with me. Did your "Datum" ( Home ) button worked?

[Enda]

There is nothing cheap about lasers, every single part costs a fortune.
i was given a quote for the ammount of spares the laser company wanted us to carry to minimise delivery time and down time. it was well over €120,000.
but saying that i know the parts will work. buying cheap ends up been very expensive and head wrecking, as we have learned.
Hope it works out for you tho.

[kyfds]

Dear sirs, not all Chinese products are poor. Indeed,the labor cost is very cheap in China.So the products are cheap mainly due to this reason. As for, my salary is less than 1500RMB per month. Frankly speaking, there're problems,but we are progressing all the time.
We produce laser machines and export. Thank you!
David
Gaoneng Laser,Wuhan,China