[Dave's_Not_Here]

Keith,

Are you looking for something like this?

[keithstanley]

Hello again everyone,

Thanks for the help so far. I thought that this was TUX, the Linux Penguin:

Image - Penguin, Commons, Common - Clipart 42936

What I was looking for was a sitting penguin like the one above but as a 3D puzzle like the d-Torso style Penguin:

d-torso store Penguin Model

Thanks to everyone. I hope someone can help

[sos13]

I hope I am in the correct forum . . . if not . . . please advice where I should post this.

Is it possible to cut a 3/4" to 1" wooden puzzle using the CNC Router? May sound like a dump question but I am trying to understand how to draw my file correctly so there isn't a big gap and the piece fit snugly.
Would I have to break apart each piece and draw individually instead of trying to cut in between ( like on a laser or scrollsaw)?

I'm new to the CNC router and surely this is possible . . any help would be greatly appreciated.



Thanks
Vicki

[Dave's_Not_Here]

SOS,

The only way to avoid or minimize your gaps between pieces, is to cut individual pieces outside the line. Keep in mind the diameter of your bit, as the corners might not fit as cleanly as you like if the inside and outside radius is too tight for the diameter of the cutter.

Do some test pieces to get the corner radius the way you want it.

You can overlay the assembled pieces with a photograph and use an x-acto knife to cut through the photograph.

Good luck...

[makecnc]

Just a quick note to let you all know the house has had some updates
to fix the engraving issue reported we just needed to mirror the parts
if you had it figured never mind but if not the files are now corrected so feel free to download again

at this link
Make CNC Product detail

[Larry83301]

I hope I am in the correct forum . . . if not . . . please advice where I should post this.

Is it possible to cut a 3/4" to 1" wooden puzzle using the CNC Router? May sound like a dump question but I am trying to understand how to draw my file correctly so there isn't a big gap and the piece fit snugly.
Would I have to break apart each piece and draw individually instead of trying to cut in between ( like on a laser or scrollsaw)?

I'm new to the CNC router and surely this is possible . . any help would be greatly appreciated.


Thanks
Vicki

You can cut puzzles on a router, just use a small bit. I have used ones as small as .014", cutting 1/8" plywood, 2 passes at 15"/min, half the depth at a time. The radius is small enough you need not worry about it, just watch which lines you cut first, and don’t cut the same piece twice. I did the Mastodon in the picture a couple of years ago, came out OK.

Larry

P.S. It’s a ***** to put back together. LOL

[macetiq]

Dear friends our forum is very stoped ,i propose a challenge,
We took a kraftpaper model and develop in wood,to the forum not stand still for weeks

[bigz1]

Dear friends our forum is very stoped ,i propose a challenge,
We took a kraftpaper model and develop in wood,to the forum not stand still for weeks

Does this count? I drew this one for Optical Power a while ago.

[cad_freak]

Hello,
I want to introduce you to my project.
It is a very beautiful setting of dxf files together, even 3D models.

to find

dxf-downloads.de

Language can also switch to English.

[sos13]

You can cut puzzles on a router, just use a small bit. I have used ones as small as .014", cutting 1/8" plywood, 2 passes at 15"/min, half the depth at a time. The radius is small enough you need not worry about it, just watch which lines you cut first, and don’t cut the same piece twice. I did the Mastodon in the picture a couple of years ago, came out OK.

Larry

P.S. It’s a ***** to put back together. LOL

Hi Larry,
Thanks for the response - yes I can make 1/8 puzzles on the laser with no problem - it's learning how to use 3/4" to 2" for the bigger stand-up puzzles - not 3-d but something the toddlers or a bit older can play with and not swallow.

I've tried using the offset/inset and cutting each individual piece - I am having a grain issue and a lot of waste. I'll keep trying LOL

Take care,
Vicki

[sos13]

nice site - I registered - waiting to be able to login without getting the 404 error page

[aarggh]

Hello,
I want to introduce you to my project.
It is a very beautiful setting of dxf files together, even 3D models.

to find

dxf-downloads.de

Language can also switch to English.

So if people upload files as ypu request, do they still need to pay to download more than one model?

And if you're paying the fee, why can't these be used for commercial projects? Are there copyright issues with these belonging to you, or they have just been collected from other sites by you?

I don't know if it's a glitch but when browsing the dxf's, the first few files I clicked on came up with 404 not found errors?

cheers,
Ian

[cad_freak]

Hello Thanks for the reply, my english is not Good. Sorry... But i try
you can Download One file per Day for Free. Every Day One. When you want more you can be a Premium User
Please Give me a link where you have the 404 error.

[sos13]

Hello Thanks for the reply, my english is not Good. Sorry... But i try
you can Download One file per Day for Free. Every Day One. When you want more you can be a Premium User
Please Give me a link where you have the 404 error.

Well I tried and tried and finally figured out that if I do not translate the page to English - I could download 1 file - HURRAY!

I don't trust Google and am using IE8 with my WinXP

Hope that helps others trying and getting the dreaded 404 error page.

Vic

[cad_freak]

Thank you for the note. I will try to fix the error. it should continue to be problems just write.

dxf-downloads.de

[DJNPHOTO]

does anyone here have a pirate ship dxf file looking to put it on a sign
thanks

[cad_freak]

Maybe something like that
Schiffe -

greetz

[souriceaux]

40w laser cutting :wave:
a small file to animate the forum.
I was inspired by a forum for this file.
Good cutting 3mm in the medium

[cad_freak]

very beautiful.
Can I publish the file with image on my site

www.dxf-downloads.de

thank you

[souriceaux]

very beautiful.
Can I publish the file with image on my site

www.dxf-downloads.de

thank you

no problem, this is for everyone
Laser cutting or CNC:banana: