Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
cooffe needs coolant
https://www.youtube.com/watch?v=_TJA5vokRpE
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
very nice 1st time i saw that video, i could not believe my eyes and ears :
... eyes : that part seems to be dragged out pretty chinky, thus there is a motivated operator ?!?! for long parts ? and i said to my slf : Johnny, la gente está muy loca
... ears : what music is on the background ?
i like the lt3000 and the multus-u3000, but so far i did not layed my hands on neither on them
i was told that this kind of instalation may get damaged if it sucks also coolant i see it extraordinary for part with short cycle, since the parts-cather may not serve the 2nd spindle, but only the 1st ( not sure about this, but also we wont get a LT soon, so ... )
kindly
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
... when there is no oil-mist :
https://www.youtube.com/watch?v=yORj8f0KFUc
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
automation for 3 axis vmc :
https://www.youtube.com/watch?v=R9zJb7j7AUA
5:45 in here : https://www.youtube.com/watch?v=f1eoL4AxEe0
why is the mr robot using the flash lantern ? is it lost ?
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
fast toolholder change for bmt turret, or how to lose the posibility to align your holders for long tools
my advice : if you wish to go that way, consider vdi i wonder if there is a way to keep the aligning possibility ...
- video 1 & 2 are about a dedicated turret
- video 3 shows how to convert a normal turret, by using some bolts, to achieve fast toolholder change
*either way, special toolholders are needed, or maybe it is possible to convert a normal toolholder ? kindly
https://www.youtube.com/watch?v=2gT_scWpxsI
https://www.youtube.com/watch?v=X6qN58O5S48
https://www.youtube.com/watch?v=QJ67QykMIdg
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
reverse spindle sense, to ged rid of the chips ( 2:15 )
https://www.youtube.com/watch?v=d1ATntHemHk
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
hello, i just saw this video : at 0.33 are double Y holders, from ews : there is a problem with making the coolant reach the cutting edge of the tool
i also have such holders, and i am working on this issue : is good to invest some time in them, so to get a better product; one of my favourite hobby is working and especially finishing stuff that is made by others
kindly
https://www.youtube.com/watch?v=CffDj--Mzuc
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
hello
there exists an intermediate guiding bush, for gang lathes, that uses air to shift inner diameter, and can handle, without problems, bars with od tolerance of 0.1mm; such equipment is not common, and normally ( without this air controlled guide bush ), is required to manually set the guiding bush ( which requires time and patience ), and also, during long term setups, the guide bush needs to be rechecked periodically; i don't have a link at this moment
also, another gadget can be found in next video / kindly
https://www.youtube.com/watch?time_c...&v=jZWsXB7KzfI
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
hello, check this out : is about monitoring & tunning the vib dampening system ( within 1.5 peeks ) / kindly
https://www.youtube.com/watch?v=VCxm3vTWgvU
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
hello again, one for the gang lathes
https://www.youtube.com/watch?v=7HdMaJ_9Kus
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg