[mactec54]

Sorry about that.
The spindle is 400hz on 220 volts 8.5 amps
Water cooled.

Sent from my SM-N950U using Tapatalk

Here are what your VFD Parameters should be set to

Huanyang Mactec54
2.2Kw 220v Water Cooled

PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=0 (1 For Remote Control)

PD002=0 ( 1 For 0-10v Terminal Control or Remote Trim Pot Control )
( J1 Also Needs to be set for Remote Terminal Control 1-2 jumper connection )

PD003=400

PD004=400

PD005=400

PD006=15

PD007=20

PD008=220 (Motor Rated Voltage )

PD009=15

PD010=8

PD011=100 ( 100 Minimum Setting with Quality VFD, 120 is Safe)

PD13= 08 is for Factory reset, Only use this to set VFD to Factory Default Settings

PD014 Acceleration=10 ( Adjust to suit)

PD015 Deceleration=10 (Adjust to suit) ( PD15 is ignored IF PD26=1 Then the Spindle will Coast to a Stop)

PD023=0 ( Forward Run Only )

PD041=8 ( Carrier Frequency up to 10 Max for these Spindle motors)

PD120=120 ( Stall Prevention )

PD141=220 ( Motor Rated Voltage )

PD142=9 ( Motor Max Amps 2.2Kw Spindle 9 amp )

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM) =3,000= (24,000)

PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD72=400

PD73=100 ( 100 Minimum RPM Setting 120 is Safe )

PD174=11 ( To Be Set to the VFD Drives Max Rated output Amps )

[millerm499]

Here are what your VFD Parameters should be set to

Huanyang Mactec54
2.2Kw 220v Water Cooled

PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=0 (1 For Remote Control)

PD002=0 ( 1 For 0-10v Terminal Control or Remote Trim Pot Control )
( J1 Also Needs to be set for Remote Terminal Control 1-2 jumper connection )

PD003=400

PD004=400

PD005=400

PD006=15

PD007=20

PD008=220 (Motor Rated Voltage )

PD009=15

PD010=8

PD011=100 ( 100 Minimum Setting with Quality VFD, 120 is Safe)

PD13= 08 is for Factory reset, Only use this to set VFD to Factory Default Settings

PD014 Acceleration=10 ( Adjust to suit)

PD015 Deceleration=10 (Adjust to suit) ( PD15 is ignored IF PD26=1 Then the Spindle will Coast to a Stop)

PD023=0 ( Forward Run Only )

PD041=8 ( Carrier Frequency up to 10 Max for these Spindle motors)

PD120=120 ( Stall Prevention )

PD141=220 ( Motor Rated Voltage )

PD142=9 ( Motor Max Amps 2.2Kw Spindle 9 amp )

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM) =3,000= (24,000)

PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD72=400

PD73=100 ( 100 Minimum RPM Setting 120 is Safe )

PD174=11 ( To Be Set to the VFD Drives Max Rated output Amps )

I tried all these parameters and it is still not being able to control the spindle with Mach3

[mactec54]

I tried all these parameters and it is still not being able to control the spindle with Mach3

Its not that you try these parameters these are the parameters that you need to have set for your VFD and Spindle, this is the starting point

If you have Mach3 correctly set and the PWM voltage is changing when you enter a different speed like M3S12000 in MDI this should give you around 5v if it does not then you have something wrong with your Mach3 setup or the Breakout Board