Yes please send me a PM if you need help still -
John
Yes please send me a PM if you need help still -
John
HELLO JOHN
I HAVE HITACHI SEIKI HS400-HS800 HAVE LOST ALL DATA. AFTER ENTERING ALL DATA WE GET
CNC ALARM
790: BRAM ERR.01 ( SYSTEM TABLE ERROR ) SYSTEM TABLE IS ERRONEOUS
PMC ALARM
2004: TOOL LENGTH OVERTRAVEL D400.4
2277: APC ARM INVERTER UNIT ALARM D427.7
PLEASE HELPL US TO MAKE OUR MACHINE HEALTHY
VIKAS KUMAR
VIKAS ENGINEERING INDIA- 9871129244
Hello all,
I have solve all of my machine alarms. Now the machine is ready and reference manually. But now the problem is when I command for reference machine value and absolute value make difference and axis is not reach at it's reference position.
Example of machine value is 359.120
Then absolute value is 35.9120 after moving 35.9120 mm machine shows alarm axis in not at reference position
Lost helical milling on VM50 with Lambda 10. Recently reloaded all Parameters.
Can't get helical milling up
Did you check your Option parameters (9000 series)
Hello,
I have a Hitachi Seiki VM50 with Lambda 10 control.
Lost helical milling after battery change.
We don't have 9000 parameter list.
Need parameter for helical option.
Thanks Much
Yes, 9000 parameters are loaded, but apparently not the helical option. I don't know which parameter or bit controls
helical. Worked fine before losing parameters.
I HAD a VM40 and the Seikos control was based on a Yasnac, it was mid 80s so maybe an MX-3, would the parameter list be the same on both controls? I'm looking for the parameter list for the MX-3 as I picked up an older machine and want to find out what options it has and what are available.
Hi I have an i80 yasnac control ..I'm trying to comp pitch error in the x axis.. book reads parameter 6801..it has a value 20000 in there right now ..I have changed it to various different numbers ranging from 0 up to 50000 but it is not changing my pitch error,Am I in the wrong parameter? After each number change I restart the machine but no change..
Thanks,Jeff
contacto: antonio aries [email protected]
[QUOTE = fantasy196; 2169101] hola
necesito manual de maquina seiki vm40 mecanizado vertical
Hola
necesito máquina manual seiki vm40 mecanizado vertical [/ QUOTE]
contact: [email protected]
Hi shas,
can you help me by resolving issue with VS50, 18M Hitachi milling machine showing an alarm 2082 (D408.2) ATC TWIN ARM ORIGIN ERROR.
It is great for me if you help me me in this to up the machine.
Hello
send me a PM with your contact info so I walk you through the process
Hi,
Need to use Block Skip 2 for bar loader. Looks like is an option in this machine.
Machine: HiCell 23B, Seicos LIII
Добрый день я не куда правильно написать
есть станок HITACHI SEIKI HiCell 23 II в режиме job все шевелиться
при попытке выполнить команды в режиме MDI
выбивает ошибки на фото видно
Пожалуйста помогите.
моя почта [email protected]
Hi all,
I have a Hitachi Seiki VM40 and I want to redo the electronics, so the plan is to replace X, Y & Z drive motors and drives and only keep the current spindle and spindle drive which are Fanuc, the motor is A06B-1003-B300 and the Control unit is A06B-6044-H103. I am not fused about being able to tap and cut threads so if someone could suggest a simpler spindle I would be happy to change. Sadly I don't have any circuit diagrams as I had someone else helping and they dropped off the edge of the world with my books.
Plan is to use Centroid equipment were possible.
Any help would be greatly appreciated.
Tony
Do You have separate driver for each motor ? Or there is 3 in 1 driver for all the Motors? We want to do same thing with vm50 but can't find any info about the Asus drive unit and if it wasn't bad enough its connected through spindle drive... If there are separate drivers and they are fanuc IT should be easy to obtain the info about signals and using something like cslab csmio get machine working with existing drivers and Motors. If I You try search on Google "vm40 Linux CNC ", there is a thread of the guy who got one fully retrofitted using Linux CNC and mesa cards. We are propably will go with new servomotors if we can' find drivers for fanucs installed in machine.
The guy that did the Linux is the guy that let me don't and has my books.
Each axis has its own drive and a Sayno Denki motor, its only the spindle that is Fanuc. Give how cheap Servo motors have become its worth just replacing with something new unless I can get new drivers and new encoder fitted to the old motors
Pm John here he is very helpfull , should hook you up with books or some info.