U10L same U100L jumpers
OSP-700L same OSP-7000L jumpers
U10L same U100L jumpers
OSP-700L same OSP-7000L jumpers
"Imagination is more important than knowledge."
hey kurmay ! secret ?
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
It is no secret that the two people know
"Imagination is more important than knowledge."
i hope i got it right : you are Okuma
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
Does anyone have experience with floppy-ethernet emulators? Some random guy fried the board handling serial transmission of our machine a few years back and since then we have been running with a floppy in our hand to the machine and back to the computer. I would rather see our machine connected to the ethernet via the floppy emulator than run with a usb-stick to the machine and back. DNC/repair costs $7000+. Not an option right now.
the link from 1st post in this thread is broken, but there is a clue ...
please consider contacting morris midwest, maybe there is a chance
Quality Machine Tools and Engineered Solutions - Morris Midwest
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
hey myhaje, check this out : 300723408804 | eBay
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
Ok, so I just recevied this:
White 3.5 1.44MB USB SSD FLOPPY DRIVE EMULATOR E100 Version for SFR1M44U100 White 3.5" 1.44MB USB SSD FLOPPY DRIVE EMULATOR E100 Version for SFR1M44-U100 | eBay
Tried the Jumpers at: M0, S1, JA, JB
And also at: S1
Still getting a disk Error
OSP-700L Controller
Kurmay, any Ideas???? Thanks for your help on here!
What is it that I am missing?? all the other emulators have worked great!
Just this **** Okuma!
our 1994 lb35 with osp7000 controls the floppy drive is on the way out and we want to convert to a usb stick drive . found a drive that is so called made for our machine comes on but throws a error is there parameters that need to be changed
Just wanted to chime in here with what worked for me. Used a 3 digit display USB, OSP-U100M on my Okuma. Had jumpers setup as instructed but was getting errors as well....found that I could view the files without issue when using MS-DOS mode.
Thanks! It's almost perfect but still need help.
Got a grey 3 digit sfr1m44-fu and installed on a OSP-7000L lath. Stock nothing worked. Changed jumper as per Kurmay's post and it got much better. I can copy both directions in proprietary format (OSP?) and can copy files from PC to USB to lath in MS-DOS format.
I still can't copy MS-DOS format to USB and see the files on PC. Both proprietary and MS-DOS files are copied to USB correctly (NC indicates successful copy) but then I can't see them on PC, only on NC. Not working either with folders created by PC or by the emulator drive.
Any ideas?
I have had a unit from Gotek model SFR1M44-FEL-DL and I'm having a similar issue. If I copy a file from the PC to the USB and then try to read it on a 7000L control I see no file (this is in MSDOS mode on the control). If I then copy a file from the NC to the USB the copy says its finished and a DIR shows the file. Back at the PC I cannot see the file only the file I originally copied on the PC. So similar to what you are seeing very strange.
HI Kurmay,
Would you know the configuration on the E100 controller by chance?
can someone post instructions for transferring programs from USB to control ? with the emulator ?
Hello there please help me
I have bout an okuma mc4va center milling machine but it does not have floppy disk and floppy to backup the system. I want to know if I buy a floppy emulator I can able to back up all of machine data?
Please let me know ????
has anyone gotten the u10 or u100 to work with both msdos and osp on these 2 or 3 digit usb emulators?
Hello,
on Monday I installed the normal SFR1M44-U100 with 3 digits for PC use in the OSP E100L. You need 3 jumpers for MO, S0 and JA. This is the same configuration as the floppy drive and runs fine.