hello, please, is it possible to use g22 for c axis ?
i wish to rechuck a part with a side hole, and orientate the hole among x axis / kindly
hello, please, is it possible to use g22 for c axis ?
i wish to rechuck a part with a side hole, and orientate the hole among x axis / kindly
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
I don’t believe it is possible because it is a spindle drive and not an axis drive. Have you tried it?
Experience is what you get just after you needed it.
hy mr wizard no, it didn't work
upper torque limit is at 60%Code:G29 PC=30 ( 2277-01 ALARM-B DATA WORD torque limit A side 1 ) G22 PC=25 C+10 F+60(100*5) G94 D+12.5 ( L0 still going ) G28
but look what i found inside error's description ( is like there is possible to use PC and PM ) :
Code:7 ->When it was not C axis connection, PC instruction was done by G22/G23/G29. 8 ->When it was not M-axis specification, PM instruction was done by G22/G23/G29. 9 ->PW and WT instructions were designated at the same time by G22.
i may be missing something, because it did not showed " no-spec alarm " / kindly
ps : please, what means WT from point 9 ?
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
I think M110 is not active?
Experience is what you get just after you needed it.
hello again no, m110 is there, i just did not shared the entire code
voilaCode:G00 X500 Z250 T909 M110 M960 M808 G00 C0 X150 G01 C1 F=60 G94 G29 PC=30 ( 2277-01 ALARM-B DATA WORD torque limit A side 1 ) G22 PC=25 C=10 F=60(100*5) G94 D=12.5 ( L0 still going ) G28 M807
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
if you wish, please check attached seems that such an option was released recently
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
Now that’s a new one! Never seen it before.
I’m guessing there is a new torque limit parameter for c axis then?
Best regards,
Experience is what you get just after you needed it.
hy, i think that this capability is there from some time, as PC appears inside manuals, in G22 context; it may be spec, but it hadn't been presented so far
from time to time, i scroll the okuma website, and recently i saw it
i think that torque limiter parameter is the same as the existing one, as it is targeting only the upper limit, beyond which is not allowed to pass when using G29
a few months ago, when i needed this, i simply used spindle's phase ( CD on screen ), and a live tool that was aligned among X axis, but offseted in Y; normally, Y offset should have been 0, but sometimes is possible to go like that now, looking back at it, i think i could have ignored also the X alingment
is possible to have same origin for C axis and M19, so to switch between them without losing phase / kindly
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
solved ... if you wish, check attaced
hy mr wizard, the capability is there from more than 10years ago, only that manuals are not updated; thus even new revisions are incomplete on some topicsNow that’s a new one! Never seen it before.
this function popped in the manuals around 2020 ... and there are still many hidden things
hello past self of myself that's because alarms related to missing specs are not always the samei may be missing something, because it did not showed " no-spec alarm
this works only for static/positioning, because as rpm increases, it will offset the m19 origin ... still, can be solvedis possible to have same origin for C axis and M19, so to switch between them without losing phase
you where thinking ? haha ... i found some of my stuff from 2018, and i was so stupid .. same for 2021, and i may still be, and miss a big thing ?! i just don't see it now, but, omg !hy, i think that this
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg
it is a good loss ... benefic
Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg