603,982 active members*
2,884 visitors online*
Register for free
Login
IndustryArena Forum > OpenSource CNC Design Center > Open Source Controller Boards > PIC Open source Servo Driver Schematics development?
Results 1 to 20 of 91

Hybrid View

Rossz PIC Open source Servo Driver... 03-10-2004, 06:33 PM
cncadmin Welcome to the site. 03-10-2004, 07:08 PM
tachus42 I have a half finished design... 07-19-2004, 06:29 AM
shahid Hi I am shahid from saudi... 03-30-2005, 05:18 PM
danadams Hi Yes, I woud be... 09-19-2006, 10:41 PM
fyffe555 the great thing about this... 07-19-2004, 03:08 PM
CNCAddict I'm very interested in a DIY... 07-19-2004, 05:54 PM
Ito-Brazil Amazing! I hope you be heare... 09-21-2004, 04:17 PM
CNCAddict Ito, whom where your comments... 09-22-2004, 07:08 AM
Greg Fill I too have been playing and... 07-19-2004, 06:00 PM
ESjaavik Greg: Yes, it's quite common... 07-19-2004, 10:16 PM
Greg Fill Thanks that makes sense ES. ... 07-19-2004, 11:28 PM
tachus42 Ok source code for my servo... 07-20-2004, 05:09 AM
CNCAddict tachus42, Do you want me... 07-20-2004, 06:11 AM
tachus42 David feel free to put it up... 07-20-2004, 07:49 AM
ESjaavik I've had the doubtful... 07-20-2004, 09:51 AM
gabrielus do you have any documentacion... 09-25-2005, 06:34 AM
ESjaavik Yes, and no. Let's say you... 07-20-2004, 09:29 AM
zekk_2 Hi There seems to be... 02-17-2005, 10:54 PM
zekk_2 Hi Einar Ref. your link to... 05-31-2005, 08:23 PM
tachus42 I must be one of the few... 07-21-2004, 02:26 PM
slp_prlzys I don't know if you guys have... 08-05-2004, 04:27 PM
CNCAddict tachus, Any updates? As... 09-12-2004, 04:11 AM
tachus42 Sorry for the low quality... 09-12-2004, 05:27 AM
CNCAddict WOW, thanx alot. I'll post... 09-15-2004, 10:50 PM
tachus42 You will need to place a... 09-16-2004, 04:36 AM
jfong tachus42, I'm a little bit... 09-16-2004, 03:18 PM
tachus42 I took the encoder polling... 09-16-2004, 03:58 PM
CNCAddict We are writing the entire... 09-17-2004, 12:08 AM
tachus42 Im not sure the motor sitting... 09-17-2004, 03:40 AM
CNCAddict I think you're right about... 09-18-2004, 07:27 AM
ESjaavik A schmitt trigger alone will... 09-18-2004, 09:37 AM
DragnsBane Just thought everyone would... 10-11-2004, 04:19 AM
ESjaavik Re: Encoder sitting... 10-11-2004, 10:29 AM
cncadmin Is that "fuzzy... 10-11-2004, 03:14 PM
ESjaavik @DragnsBane: That link just... 10-11-2004, 10:34 AM
DragnsBane sorry about that sometimes mt... 10-11-2004, 03:02 PM
sbrpollock I,m very impressed by this... 10-11-2004, 06:28 PM
tachus42 Patrick avrfreaks.net is a... 10-16-2004, 01:02 PM
heyarnold Recently DragnsBane asked if... 10-17-2004, 07:20 AM
ESjaavik @Paul: Actually I'm not sure... 10-17-2004, 09:41 AM
heyarnold Elm Smc 10-17-2004, 03:54 PM
ESjaavik What about the cost? Too high... 10-17-2004, 07:41 PM
cncadmin That's fine with me. 02-08-2005, 02:24 PM
lerman ATmega16 Seems Fast Enough to... 12-06-2004, 02:05 AM
Hardwarekill Here on this Link is an... 12-06-2004, 02:46 AM
ESjaavik @Hardwarekill: I have... 12-07-2004, 12:13 AM
ESjaavik @lerman: Did you consider... 12-07-2004, 12:51 AM
Hardwarekill @ESjaavik The Quellcode or... 12-07-2004, 03:57 AM
jshroff Hi do you know where I can... 03-31-2005, 02:33 PM
lerman Why I Would Not Use Counters 12-09-2004, 02:41 AM
mmjpotter Some interesting ideas on... 06-01-2005, 12:36 AM
mmjpotter I appreciate that this thread... 06-01-2005, 03:20 PM
Vider If it is usefull, here you... 03-31-2005, 02:55 PM
James Newton 1. The source of the step and... 06-01-2005, 06:10 PM
mmjpotter Thanks James. I think you... 06-01-2005, 08:58 PM
James Newton "Why design a servo driver... 06-01-2005, 09:16 PM
Mariss Freimanis Its the old "chicken or egg"... 06-02-2005, 01:03 AM
SimonArthur James: What does the... 07-06-2005, 05:56 AM
Vider Dear friends: As I see... 07-06-2005, 07:47 AM
slp_prlzys Trajectory generator? 08-03-2005, 03:56 PM
smarbaga tachus42 can u convert your... 09-24-2005, 03:03 AM
smarbaga spl the trapeziod must be... 09-24-2005, 03:25 AM
dirk c Hi to everybody, I picked up... 10-02-2005, 08:43 AM
smarbaga show me the schematic ro a... 10-02-2005, 11:37 AM
Luslugger http://www4.ncsu.edu/~dsbloomf... 10-08-2006, 02:40 AM
venomx999 I have these DC servo motors... 03-06-2007, 05:51 PM
zoltan It is $100 each? Are you... 03-06-2007, 08:59 PM
spotlite Hi, I think I have easy... 11-19-2007, 09:33 PM
pongthep Very Good post for knowledge 01-12-2008, 02:23 AM
agelkom I made a single side PCB for... 01-28-2008, 01:22 PM
James Newton Are you willing to share that... 01-28-2008, 11:00 PM
agelkom Linistepper PCB 01-29-2008, 03:00 PM
astal thanks 07-25-2009, 02:58 AM
agelkom Linistepper Lini8 PCB 02-01-2008, 01:18 PM
agelkom Hi, Here is the PCB copper... 02-06-2008, 10:34 AM
RRR Hi Argun, It's very... 02-17-2008, 04:05 PM
tady tachus42 coud you please post... 02-16-2008, 10:32 PM
agelkom Linistepper New Board 02-18-2008, 03:36 PM
agelkom Linistepper Lini8 New PCB 02-21-2008, 01:15 PM
RRR Hi Argun, Some components... 02-22-2008, 12:03 AM
agelkom components for lini8 02-22-2008, 12:23 PM
Tariq Assar Hi, Lini8 charge-pump... 10-26-2011, 09:37 PM
Tariq Assar Hi, Lini8 charge-pump... 10-26-2011, 09:37 PM
brave1brave Hi to community :) (this is... 04-03-2009, 11:23 AM
pieroandreini Hi, just redrawn schematic... 03-20-2011, 02:23 PM
berin So is this a servo driver or... 10-07-2011, 05:23 PM
James Newton berin, you are absolutely... 10-07-2011, 05:47 PM
  1. #1
    Join Date
    Jun 2003
    Posts
    125
    tachus42,
    Do you want me to put this on my webpage so it can be referred to more easily? I am trying to learn as much as I can about AVR's, and this looks like a fun project.

    David B.

    www4.ncsu.edu/~dsbloomf

  2. #2
    Join Date
    Apr 2004
    Posts
    169
    David feel free to put it up on page jusr credit me, Stephen Dredge ( not that i think the code is that worthy)
    The code was compiled with the gcc-avr http://winavr.sourceforge.net/
    And I use pony prog to program the avr http://www.lancos.com/prog.htm with the (STK200/300) parallel port interface descibed on the pony prog page.
    The LCD Port will connect to a standard 2 * 16 LCD with a ribbon cable and the keypad is a 4*4 matrix.

Similar Threads

  1. Open Source Driver electronics
    By pminmo in forum DIY CNC Router Table Machines
    Replies: 1
    Last Post: 11-22-2009, 09:42 PM
  2. Any ideas for open source CAM package?
    By galacticroot in forum OpenSource Software
    Replies: 26
    Last Post: 10-22-2007, 05:35 PM
  3. Open Source CNC Controller Specification
    By gregmary in forum DIY CNC Router Table Machines
    Replies: 28
    Last Post: 12-05-2005, 04:58 AM
  4. 2nd Generation DeskCNC servo driver released
    By imserv in forum News Announcements
    Replies: 0
    Last Post: 11-25-2004, 01:22 AM
  5. Open source driver designs
    By pminmo in forum CNC Machine Related Electronics
    Replies: 0
    Last Post: 05-05-2004, 03:29 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •