Anybody out there have, or know of, anywhere in the world to access manuals for an Okuma-Howa HL20 lathe. It's a 2000 with Fanuc 18T controller. Willing to beg, borrow, rent, or buy.
Anybody out there have, or know of, anywhere in the world to access manuals for an Okuma-Howa HL20 lathe. It's a 2000 with Fanuc 18T controller. Willing to beg, borrow, rent, or buy.
What are you needing out of the manuals? Sample codes, alarm list or programming format, I've got a 1999 ACT-20 with an 18T.
Hey rickyt, thanks for the reply!!!! Biggest problem at present is 'home zero' that wanders around(both axis, and turret position). This all started with a couple months of machine sitting idle,and the back-up batteries went dead; upon restart I had operator message EX 208 on screen, and alarm lite and beeper, and machine was alarmed out. Further digging showed ACP300 alarms for X,Z, and A(turret) axis. Replaced batteries and got rid of 300 alarms thru reset of 1815 parameters, and after MUCH fooling around, finally got rid of 208. However, turret doesn't seem to index like it used to, and in trial running (no work in chuck) an old practice program, the tool called for is not the one to index up(guess I may need to know how to do that,too). Anyway, when moving around axis's in manual mode, things seem fine, and 'home' mode goes back and lites come on; but when we run the practice program, the 'home' zero moves around on us(sometimes quite drastically). Repeated resetting of 'home' zero thru prameter 1815 has not got it to 'stay put'. Of course the Fanuc manuals take you just so far, and then refer you to your 'machine tool builder', NEAT!!! Any help would be GREATLY appreciated, Thanks howd.
we have recently purchased okuma 7 howa act-3 we want english machine manual if you have please confirm we have manuals in german language.
we have okuma & howa act-3 in manuals in german if you have in english please confirm.
Dear All
RUN YOUR CNC MACHINE WITHOUT TROUBLE THIS IS FOR ONLY DELHI AND NCR CNC CUMMUNITY INDIAN CUSTOMER
WE ARE BASED IN DELHI FOR YOUR SERVICE
if your cnc machine is under breakdown and u want to start that
then contact == [email protected]
we work with all VMC ,DOUBLE COLUMN,HMC,turning cnc machine (imported one INDIA AND TAIWANI ) EQUIPED WITH BELOW MENTION CNC SYSTEM
FANUC ,MITSUBISHI,MAZAK,MELDAS,OKUMA OSP,SIEMENS,FAGOR
THANKS
how to set offset for 1st and 2nd tools for okuma & howa act 3 cnc lathe.
what kind of control has this ACT3? is it Okuma or Fanuc?
please help me, I have one machine daewoo milling model ACE-V500
the machine have alarm No 2103 MUST BE COMMAND MANUAL ATC 1 CYCLE
i don't have any manual, if any body have manual maintennance book, please can send to me
Vu Tri Nhat
Vu,
Is your machine an Okuma ?
or a Daewoo ?
if it's a Daewoo (wrong)
I don't think you will find a Kia part at a Toyota shop!!
This is for "howd", if you are still reading this post. I have the procedures for setting these home positions including the reteach procedure for the turret. It may be as simple as the way you are setting the 1815 ref position. Basically, if you already have a 1 in there then you change it to a zero, turn off control, turn back on, go back to the 1815 parameter and change it back to a 1 but then you must power it back off and on again or it will not take the change and hense the change you think you have made did not take and so the machine still has a bad ref position. If you have done it this way then we can look elsewhere. Let me know an e-mail and i can get these to you after the holiday weekend. These procedures are written by hand to include each button pressed. More detailed in laymans terms than factory. They are in Adobe pdf. Good Luck
it is fanuc 10 t control.
hi
I have problem ops300m error W02 but am dont have catalog okuma osp 300M
what this error if you know?
Hi all.
Is any one know where and how to get the manual of Okuma Howa CNC machine, model FM-30V with Sony NU-99 control unit?
Or how to get, edit and tranlate program from/ to PC via RS232 port?
Thanks in advance.
Nam.