I'm one that has never posted here, but being part of the 7000+ viewers, I just wanted to say that this thread is a real enjoyable education for me......More pics! .....can't seem to get enough of the interest you generated here.
Bloy
I'm one that has never posted here, but being part of the 7000+ viewers, I just wanted to say that this thread is a real enjoyable education for me......More pics! .....can't seem to get enough of the interest you generated here.
Bloy
.....
.....
Just ad an Fx on the same line as the first G1
N009 G01 X10 Y0 F10
for example.
Gerry
UCCNC 2017 Screenset
http://www.thecncwoodworker.com/2017.html
Mach3 2010 Screenset
http://www.thecncwoodworker.com/2010.html
JointCAM - CNC Dovetails & Box Joints
http://www.g-forcecnc.com/jointcam.html
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
.....
There might be a default speed in your controller software, or it might be using the max speed you have the motors set to.
Gerry
UCCNC 2017 Screenset
http://www.thecncwoodworker.com/2017.html
Mach3 2010 Screenset
http://www.thecncwoodworker.com/2010.html
JointCAM - CNC Dovetails & Box Joints
http://www.g-forcecnc.com/jointcam.html
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
.....
No worries IJ,
e-mail me your stl file and we will go through it.
"A Helicopter Hovers Above The Ground, Kind Of Like A Brick Doesn't"
Greetings From Down Under
Dave Drain
Akela Australia Pty. Ltd.
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
.....
.....
.....
Very nice IJ! Have you done any work that would approach the limit of the machine as far as ridigity? I am very curious as to how well this type of mill preforms.
PS, still battling my drivers. The people here have given me some suggestions and I can't wait to try them out tomorrow in hopes that one wll fix my problem.
Proud owner of a Series II Bridgeport.
.....
I would love to get a knee mill similar to yours and retrofit it in the future. Ebay is not a bad place to pick them up used. I've seen suitable ones go for just over a a grand, with tooling.
Maybe I missed this in the thread but have you been able to get a good reading on the accuracy?
Proud owner of a Series II Bridgeport.
.....
Great thread! I'm about to finalize the purchase of a used Bridgeport clone this week, with the hopes of converting to CNC.
IJ, you said you still have complete manual control if you ever want it. How would you manually move the quill? Or can you only move the knee when in "manual" mode?
Also, what is the long travel of the table? What was the travel before the conversion? And what is the table size of your mill? I'm looking at a 9x42 mill (only size in my area), and I will need every last bit of the 30 inch travel for the work I want to do with it. I am figuring I will have to make some sort of extension about 12 inches long that is of a smaller cross section than the table, so that the stepper/servo will not hit the knee and limit the travel.
Finally, could you have mounted the servo for your Y axis so that the motor pointed inwards? That should have given you more room for your legs when standing in front of the machine. Was there a reason you chose to do it like you did?
Thanks,
Nick
.....
Nick,
Attached is an image of my Y-axis motor mount in progress. As IJ said, facing the motor inward makes the belt pretty long.
Regards,
Rick
But it shouldn't really matter if the belt is long, does it? I mean, they are usually steel inforced or similar.
Cheers,
Sven
.....