588,166 active members*
4,251 visitors online*
Register for free
Login

Thread: X axis over travelling during run.

Page 3 of 3 123
Results 41 to 44 of 44
  1. 04-24-2012, 07:22 PM #41
    JayCop
    JayCop is offline Registered
    Join Date
    Dec 2010
    Posts
    0
    For some reason Kmotioncnc does not recognize this line of code: N14G70G91.1
    That line of code is in the original file and the warpdrive file.

    If I remove it I can run the simulation. When I view the warpdrive version the arcs are now straight lines between the two outer straight lines. Not sure what the cause of this is.

    Attached are all the files I tried and the originals.
    Attached Files Attached Files
    Reply With Quote Reply With Quote
  2. 04-24-2012, 10:15 PM #42
    ger21
    ger21 is offline Community Moderator
    Join Date
    Mar 2003
    Posts
    35538
    It probably doesn't like G91.1, which is incremental IJ mode in Mach3.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
    Reply With Quote Reply With Quote
  3. 04-24-2012, 11:02 PM #43
    PaulRowntree
    PaulRowntree is offline Registered
    Join Date
    Jan 2008
    Posts
    853
    Yes, I mention that in the WarpDriver manual, I just comment it out in the source window before warping. By memory removing this line affects the mm/inch interpretations too, so make sure it is back in place for any files that you are sending to the machine and Mach3.
    Reply With Quote Reply With Quote
  4. 04-25-2012, 01:26 AM #44
    PaulRowntree
    PaulRowntree is offline Registered
    Join Date
    Jan 2008
    Posts
    853
    Looks good to me JayCop! Good luck with it.
    Cheers!
    Reply With Quote Reply With Quote
Page 3 of 3 123
« Previous Thread | Next Thread »

Similar Threads

  1. The Widgitmaster's Travelling CNC Medicine Show
    By BobWarfield in forum DIY CNC Router Table Machines
    Replies: 8
    Last Post: 04-22-2024, 10:11 AM
  2. Unwinding the rotary axis ( 4 axis rotary axis milling fanuc control)
    By diaa beheiry in forum PowerMILL
    Replies: 1
    Last Post: 11-17-2015, 07:37 PM
  3. Speed (RPM) and travelling speed.
    By einarkol in forum Material Machining Solutions
    Replies: 0
    Last Post: 12-27-2008, 07:04 PM
  4. New Design - Hybrid 3-Axis Router/4-axis Foam Hot Wire Cutter
    By the__extreme in forum CNC Wood Router Project Log
    Replies: 3
    Last Post: 02-26-2007, 09:58 PM
  5. travelling salesman
    By ghyman in forum Visual Basic
    Replies: 7
    Last Post: 10-27-2005, 11:16 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules