587,787 active members*
2,844 visitors online*
Register for free
Login

Thread: Config/State only for licensed Mach 3??

Results 1 to 4 of 4
  1. 07-25-2007, 09:42 PM #1
    Mr. Technical
    Mr. Technical is offline Registered
    Join Date
    Oct 2006
    Posts
    90

    Config/State only for licensed Mach 3??

    Hello All,

    I am trying to set up a trial version of Mach 3 (mill) to work with a 3rd party break out board. The instructions that came with the board refer to going into 'Config/State'. I have been unable to find that in the Config menu. Am I looking in the wrong place, or do I need to buy the full version to get access to that area? I plan to buy soon, but have to recuperate a little from the cost of the mill. Any help is greatly appreciated. Thanks!!

    Ian
    Reply With Quote Reply With Quote
  2. 07-25-2007, 10:56 PM #2
    rmtucker
    rmtucker is offline Registered
    Join Date
    May 2003
    Posts
    79
    The menu has changed a little in newer versions of mach3.
    State could now be in Config/General Config.
    What setting are you trying to change?

    Regards
    Mark
    http://www.weardalecnccarving.co.uk
    Reply With Quote Reply With Quote
  3. 07-26-2007, 12:07 AM #3
    ger21
    ger21 is offline Community Moderator
    Join Date
    Mar 2003
    Posts
    35538
    Config>logic and config>state have been combined into general config in the latest versions.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
    Reply With Quote Reply With Quote
  4. 07-26-2007, 02:34 AM #4
    Mr. Technical
    Mr. Technical is offline Registered
    Join Date
    Oct 2006
    Posts
    90
    Thanks for the info! I need to turn on macropump.
    Ian
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. config settings for mach 2
    By fidia in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 3
    Last Post: 07-04-2007, 11:18 AM
  2. Confused in Mach 2 enable pins config,it's mapping to XYZ or not?
    By szcharle in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 0
    Last Post: 02-15-2007, 12:23 PM
  3. State of the art job shop?
    By MrGixer in forum Community Club House
    Replies: 12
    Last Post: 06-17-2006, 06:40 PM
  4. Mach 3 config?? HELP
    By ty1295 in forum Servo Drives
    Replies: 3
    Last Post: 02-20-2006, 07:20 PM
  5. Mach 2 config questions
    By randyf1965 in forum Mach Software (ArtSoft software)
    Replies: 1
    Last Post: 04-20-2005, 04:05 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules