586,067 active members*
4,872 visitors online*
Register for free
Login

Thread: Radius to end of Arc Differs From Radius to Startline

Results 1 to 3 of 3
  1. 08-10-2010, 01:53 AM #1
    Bob La Londe
    Bob La Londe is offline Registered
    Send a message via ICQ to Bob La Londe Send a message via Yahoo to Bob La Londe
    Join Date
    Oct 2008
    Posts
    2100

    Radius to end of Arc Differs From Radius to Startline

    Radius to end of Arc Differs From Radius to Startline

    Ok... Why? I mean I used this G-code file to cut an actual work piece under my previous profile. However under the Gecko XML I get this error.

    What setting would be different that the code would be good in one, but not the other?

    I reloaded my old profile and loaded the same g-code file just to make sure and it did not stop at this as an error.
    Bob La Londe
    http://www.YumaBassMan.com
    Reply With Quote Reply With Quote
  2. 08-10-2010, 02:58 AM #2
    Bob La Londe
    Bob La Londe is offline Registered
    Send a message via ICQ to Bob La Londe Send a message via Yahoo to Bob La Londe
    Join Date
    Oct 2008
    Posts
    2100
    Sorry if I posted that in the wrong area, but since it was related to a Gecko Drive change and XML file... oh nevermind. Just glad its where you want it now.
    Bob La Londe
    http://www.YumaBassMan.com
    Reply With Quote Reply With Quote
  3. 08-10-2010, 03:16 AM #3
    ger21
    ger21 is offline Community Moderator
    Join Date
    Mar 2003
    Posts
    35538
    It's a Mach3 issue, not a Gecko issue, so I moved it to the Mach3 forum.

    As you saw in the Mach forum, it's probably due to the IJ mode. Change it in General Config.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. "Radius to end of arc differs from radius to start on Line #"
    By labuda in forum G-Code Programing
    Replies: 8
    Last Post: 11-15-2009, 01:35 PM
  2. Radius to end of arc differs from radius to start?
    By Jamy in forum LinuxCNC (formerly EMC2)
    Replies: 2
    Last Post: 08-23-2009, 05:28 AM
  3. radius help
    By Scott Halstead in forum GibbsCAM
    Replies: 0
    Last Post: 06-12-2008, 01:27 PM
  4. "Radius to end of arc differs" problems !
    By Geetar-ist in forum G-Code Programing
    Replies: 7
    Last Post: 12-16-2007, 07:22 PM
  5. Zero Radius Arc
    By Xular in forum Mach Mill
    Replies: 4
    Last Post: 12-14-2006, 04:10 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules