please help
I have problems amada pega 357 04pc
in turn I get system error
We have motherboard
built on and off then comes the turn on
system error
how I can
please help
I have problems amada pega 357 04pc
in turn I get system error
We have motherboard
built on and off then comes the turn on
system error
how I can
which system error? Are there lights on? Does the screen say anything? Be as specific as possible.
yes I have deleted memory
machine was again 0
right page button MEMORY TAPE MANUAL EDIT MDI is off
system restarts
said parameter active and alarm 417 427 437
all parameters re-entered
then I can not disable parameter
I give 0 not go
but I have punched tape parameters
tape reader not funksioniert
how can I bring back machine run
Thanks
did you also enter the DIAGNOSTIC (300~650) parameters?
DIAGNOSTIC (300 ~ 650) parameter
I entered manual
now I've turret and index problems
alarm in 2000 and 06 interlock
and no alarm in 2009 how I can
I need no parameter which
I have to change parameters
There are 2 errors which which we are getting with the machine
No.-222 +Y S LMT
And when we are correcting that error another error is occurring
No.-220 +Y OT
These error are regarding some parameter settings, may be these error relates to PARAMETER numbers 81, 82, 83, 84.
Can you let us know what this error is and if we can find complete manual which will tell us what to do.
Hello!
Can you please send me Diagnostic parameters for Amada Pega 345 Fanuc 04pc controller to my jayratio at gmail . com
That will be a great help.
Thanks,
Ajay
I have an amada pega 357 with fanuc 04p control. We have had lots of issues and this machine is new to us. I need some help. Today when trying to run a program the machine just stopped and the clamps released. Ive tried to reset and do everything I know how but I cant get the clamps to close. The foot pedal has no response.
I dont know my way around the machine well enough yet to even know what fuses, breakers, cords, etc to check. Can give me a list of items to check or troubleshooting procedure
I did notice that usually when we power on the machine the control usually comes on, then the hydraulic, then there is a multiple clicking sound that I believe may have been the clamps, after the clamps stopped working that sound no longer happens.
please help. Ill even pay for tech support if someone can offer it and truely knows this machine.
email or text
618-709-9262
[email protected]
My Amada machines lost all parameters because of long electric failure and the batteries did not hold.
When the power was restored the Amada machines already had lost everything.
Amada Apelio II 357 05PLA( Combi machine Laser Punch )
Amada Pega 244 04PC ( Punch Machine )
Do you have backup parameters for this machines if possible also the MMC parameters.
Hello,
I am servicing a Amada Pega 345 with Amadan 04PC and The machine is not getting the signal for the TDC, I checked the sensor and it is working, even the signal is in the card, I am looking for documents where i can see how the signal goes from one card to another to see if the wire is broke
Jorge B.
jorbercnc.com
I sent reply, I dont see it posted.
1. Check wires P2-N2 should be 24VDC
2. Check diagnostic 2008.4, is it 0 at TDC? Put steel in front of switch on / off will diagnostic 2008.4 change? Jog ram off TDC to get cam out of your way for testing
3. King Or Queen machine? Queen has hyd clutch
4. Open door with main breaker. Large board inside at top of board should have number TCU1, is it A,B,C? Different schematic for each.
Hello.
1. The 24v is Ok
2. The diagnostic 2008.4 is not changing even in the sensor the LED I can see lightning when put the metal in front. Also I see the leds in the board as in the picture.
3. Is Queen
4. Now I am away to see that but let you know later
Thanks
Sent from my iPhone using Tapatalk
Jorge B.
jorbercnc.com
[QUOTE=jorber;2218266]The Board is TCU1C-00A
TCU signal Wire #156 comes into TCU1 board on TM1 Pin 6.
signal comes out TCU1 M18 Pin 17.
See if you have signal change in and out of TCU1.