[rlwoodjr]

Hello,
I have been a member here for awhile in the DIY router forums. I finally decided to try my hand at machining with a Bridgeport. So far it seems to be in good condition. I have converted it to Gecko stepper drivers and I am using Turbocnc. I am using a static phase converter for the spindle motor. The stepper motors are from Centriod. It came with some tooling.

I am looking for a part list and a maintenance/repair manual and some history or date of this machine. It is serial number CNC 1696.

[rlwoodjr]

Added computer stand

[TarHeelTom]

Wow! You've done a nice job. One difference is that I'm putting all the electronics, including the computer, inside the power cabinet, where you've got a nice little cabinet there on the side. Was that already on the mill, or did you add it?

I have one quite similar to yours, but haven't quite finished the conversion yet. Was too hot to work in the garage in the summer, and too cold in the winter, so took a long break to insulate the garage. You can see mine at Tom Wade -- Machinist Section -- New CNC Mill.

Maybe you can help. I'm wanting to do various sorts of engraving, including lithophanes. Thinking of making a router mount which would mount in the spindle. I've got, for instance a monster 1" end mill holder. Was thinking of welding a 1" shaft to a holder for a router. Would like to keep the entire assembly as short as possible, and try to keep the router centerline matched up with the mill spindle centerline.

Any ideas what might be the most suitable router? Seen any router holders which would be more appropriate than others?

Thanks

Tom

[rlwoodjr]

Tom,
I had the big box on the back full of transformers, but I wanted to put it close to a wall. A guy at work had the smaller box that I put the electronics in. I only kept the 2 spindle relays from the big box.

I have seen your web page before when I was looking for a mill. Great page for someone just getting started. Once I bought mine I started wondering how I would get it in the shop. I finally decided to remove a 4' section of wall. The guy I bought it from delivered it right to the shop floor.

I am not sure I would use the bridgeport for a router....maybe to make parts for a cnc router. Here is a link to the one I made for my dad:
http://www.cnczone.com/forums/diy-cn...d_one_dad.html

My Brridgeport has 18" in X, 12" in Y, and 5" in Z. A Larger DIY router project for engraving and lithophanes could be done for a reasonable amount.


I have plans for a 5 axis machine...but too many projects not enough time.

I used the small Bosch trim routers for mine.

[TarHeelTom]

Tom,
I had the big box on the back full of transformers, but I wanted to put it close to a wall. A guy at work had the smaller box that I put the electronics in. I only kept the 2 spindle relays from the big box.

I have seen your web page before when I was looking for a mill. Great page for someone just getting started. Once I bought mine I started wondering how I would get it in the shop. I finally decided to remove a 4' section of wall. The guy I bought it from delivered it right to the shop floor.

I am not sure I would use the bridgeport for a router....maybe to make parts for a cnc router. Here is a link to the one I made for my dad:
http://www.cnczone.com/forums/diy-cn...d_one_dad.html

My Brridgeport has 18" in X, 12" in Y, and 5" in Z. A Larger DIY router project for engraving and lithophanes could be done for a reasonable amount.


I have plans for a 5 axis machine...but too many projects not enough time.

I used the small Bosch trim routers for mine.

I also need to put it close to a wall, so moved the power box to the side. Since I am using a VFD, I tossed the spindle relay. Actually, I don't foresee a huge demand for the low gear, so don't plan on using the reverse gear very often.

Good job on the table you're building for your dad. May get back with you if I decide to build a table. I don't particularly like the idea of using the Bridgeport for the lithophanes, but a couple of guys have shown some commercial interest in the lithophanes, so will use the Bp to make a few. If the interest turns to income, I'll then build a router mount for the BP, then start on a router table. Btw, what was your build time on your dad's router?

Big problem here is space. Seems like I saw a thread where someone built a router table which stands the work on edge.

Like your rotary drive. I stumbled across a 12" manual rotary table at a good price. Need to find a stepper for it, then turn a mount to hold it and drive the shaft behind the handwheel and I'll be in business. Also need to build a tailstock for it. But your rotary drive is probably all the size I really need, for the work I'd like to do.

But at least I had the foresight to buy mine in warmer weather ! ;>}

[rlwoodjr]

I can't really say how long it took to build the router because I only worked on it on select weekends. If I had to guess, I probably have 40 to 50 hours into it.

Space seems alway to be a little less than you need. Adding the bridgeport to the shop makes it a little bit more cozy...

I am looking for a rotary table for th BP...hopefully I will find one for a good price. Notice I made room for the 4th axis in the black box.

Did your BP come with any manuals?

[mactec54]

The Boss 5 & below have a 1/1 ratio motor to ballscrew, A Boss 6 on have a 2/1 ratio
there is not much difference from a 3 to a 5 mostly just in the control, as you don't use the control anymore
there's not much to the machanics of the machine

[rlwoodjr]

I guess mine is a Boss 5 or below... I did order a manual on eBay. I have not received it yet, but it should be here soon.

[TarHeelTom]

There is currently a complete BOSS 5 box for sale on ebay. It includes a full set of digital manuals. There is a link to it on this site in the for sale section.

Hopefully someone here will get a hold of that set of manuals and either post them here, or give me a set and I'll post them on my web site, or both.

Tom