[Antonio Arguijo]

Hello!
Someones knows how change the configuration chuck, as spindle or as axis, because after charge all software, we can't run the spindle or chuck 850 RPM more, the control is OSP700L but I don't have some manual to know what parameter must modify to increase the spindle speed.

[fordav11]

that speed could be the limit for the gear you are in. try changing to high gear.

[cnc machining]

At the MDI function try key in M3 S850 M42 then follow by cycle start.

[Antonio Arguijo]

that speed could be the limit for the gear you are in. try changing to high gear.

How change to high gear?

With M42 ?

[Algirdas]

M40 neutral, M41 slowest, M42 middle, M43 high (if your machine has three of them)

[Antonio Arguijo]

M40 neutral, M41 slowest, M42 middle, M43 high (it your machine has three of them)

Thnks a lot for your help!

Regards!

[mrphuocauto]

Hi ALL!
I have the issue with this model!
First, i want to change battery and power on
Alarm: 128 Memory disk format!
Please help me to solve this Problem
thank you verry much

[Algirdas]

1. change the battery. Do it smart way: connect additional power supply in parallel first and only then replace the battery. Otherwise you'll need a special procedure.
2. re-install the software. there is something wrong.

[mrphuocauto]

THANK YOU ALGIRDAS
-now I do not have the disk in the machine, not the other way
please specific guidelines that must be how my half
I do not know much about Okuma
please help me
thankkkkkk......

[Algirdas]

can you descrbe more specific, when do you get the message

Alarm: 128 Memory disk format!

are you sure, it's just "Alarm"? Isn't it "Alarm P" or "Alarm A" or somethong like?

[mrphuocauto]

HI ..ALGIRDAS
when I open up the source of the display as shown below
forward to help
Sorry for my english slightly less
Attachment 200914

[fordav11]

That's a serious problem. your machine is not even working or booted up properly.
As a minimum you need to re-install the system software from your floppy disks.
If you don't know how to do that or you don't have the floppies you need to contact Okuma for professional assistance.

[mrphuocauto]

OK THANK YOU ......FORDAV11
Such problem is that I did not have a system disk
I know that someone will find this disc where no
I would buy this disc and the way my Okuma machine operators
* I honestly grateful for the help of your enthusiasm
good fun

[Algirdas]

illustration is good.
so, your control doesn't start booting, as Mr.fordav11 noted already. You have SBP monitor message.
SBP monitor is tiny small program which checks hardware before operating system boot. Memory detection is the first checkpoint when CPU is powered and clocked.
You have an error on 0000 address on the very first step of hardware check.
There are two places to check first:
1. Control rack. Check if there are no error indication on Opus face panel
2. Control set. Some modules are missing or faulty.
Generally saying you're in deep deep crap without installation media and proper Okuma support.
The reasons of condition like that could be:
1. Uncompleted/ improper reinstallation of Okuma operating system.
2. hardware fault.
3. missing module (most likely at this case)

[mrphuocauto]

hi..algirdas
number (0000) is not your fault, that they entered a try nothing changes
sorry for not saying this before

[Algirdas]

number (0000) is not your fault

it indicates the initial fault of test. memory test is the very first one in the test sequence. So, your control is faulty at the very start of tests. By the way, when you contact Okuma support, tell them, that you have alarm "106" on memory test test block "0000" in SBP monitor