[mflux_gamblej]

Hey guys, I don't post here often, just over in 'bridgeport / hardinge machines.'

I'm looking at buying a used Takisawa TS-15 lathe. The lathe has a fanuc 6t-b controller. It's been really tough trying to locate manuals for this control even though its a fanuc.

I also need manuals for the lathe itself. That's even more obscure I believe.

Anyway, if anyone has 6t-b manuals, I'd be happy to buy them or a copy from you (right away!!)

Thanks

[fordav11]

you can buy 6T manuals on ebay (etc). no PDFs are available.
if you just need basic programming info any Fanuc manual will do with only minor differences. mostly you need to use G50 to set X/Z tool positions. Much of the rest is the same.
Programming-wise, Fanuc 10-15 series is closest. 15B manual is available free online in pdf.

[mflux_gamblej]

you can buy 6T manuals on ebay (etc). no PDFs are available.
if you just need basic programming info any Fanuc manual will do with only minor differences. mostly you need to use G50 to set X/Z tool positions. Much of the rest is the same.
Programming-wise, Fanuc 10-15 series is closest. 15B manual is available free online in pdf.

Indeed it has been tough to find this as a PDF. I've found a couple of possible manual sources. My big worry is that I have an appt. to see this machine under power (and write a check for it) on Jan. 25 (in 6 days) and I need to learn as much as possible before that.

[yours_prabhat]

Here are the alarm list for fanuc :

Fanuc 6 Alarms

Program errors or Operator's Error

000
Re-apply the power after the parameter has been input
001
TH Alarm (A character with incorrect parity was input) Correct the tape
002
TV Alarm (The number of characters in a block is odd). This alarm will be generated only when the TV check is effective
003
Data exceeding the maximum allowable number of digits was input
004
A numeral or the sign (-) was input without an address at the beginning of the block
005
The address was not followed by the appropriate data but was followed by another address of EOB code
006
Sign "-" input error (sign "-" was input after a address with which it can't be used. Or two "-" signs were used).
007
Decimal Point "." Input error (A decimal point was input after a address with which it can't be used. Or two decimal points were input).
008
The switch position of the tape reader was not AUTO (without reel) or REEL ON/REEL OFF (with reels).
009
Unusable character was input. (E).
010
A unusable G code was commanded. (The alarm is generated also when a G code with which the control is not equipped as an option is commanded).
011
Feedrate was not commanded at cutting feed or the feedrate was inadequate
015
The number of the commanded axes exceeded that of the allowable simultaneously controlled axis
017
The move commanded of the additional axis was commanded without equipping with an optional additional axis.
018
An additional axis was commanded with the other axis simultaneously.
021
The axis not included in the selected plane (by using G17, G18, G19) was commanded in circular interpolation.
022
In circular interpolation, radius designation was performed in the NC which is not equipped with the radius designation option.
023
In circular interpolation by radius designation, Zero was commanded for address R.
030
The tool offset number is too large for the D or H function.
031
In setting of offset amount by G10, The offset number following address P was excessive or it was not specified.
032
In setting of offset amount by G10, the offset amount was excessive.
035
Skip Cutting (G31) was commanded in cutter compensation mode.
036
G45-G48 (Tool Offset) was commanded in cutter compensation mode.
037
The selected (by using G17, G18 or G19) changed in cutter compensation mode.
038
Over cutting will occur in cutter compensation because the arc start point or end point coincides with arc center
041
Overcutting will occur in cutter compensation.
044
One of G27-G30 was commanded in canned cycle mode. An ATC cycle (M06) was commanded in canned cycle mode.
045
An ATC cycle (M06) was commanded for the NC which is not equipped with optional reference point return feature.
046
Other than P2, P3 and P4 was specified in the 2nd, 3rd and 4th reference point return commands.
047
G27 to G30 was commanded for and axis which does not have a reference point.
058
In 4-digit S code binary 12-bit/analogue output A, A command was specified exceeding the maximum or minimum number of spindle revolutions.
059
No program for selected work number is found (external work number select A function).
060
Commanded sequence number was not found in the sequence number search,
065
Scaling Magnification was specified as other than 1-99999.
066
Scaling was applied and as a result, movement value, coordinate value, circular arc radius, etc. exceed maximum programmable dimension.
067
G51 (scaling ON) was specified in cutter compensation mode.
070
The Fanuc memory area is insufficient.
071
The address to be searched was not found.
072
The number of programs to be stored exceeds 95 or 191. (191 is a option(.
073
The program number has already been used.
074
The program number is other then 1-9999
075
The program number or sequence number was not found at the start block of the program
076
The address P was commanded in the block with includes a M98 command.
077
The subprogram was called in triple
078
The sequence number which was specified by address P in the block which includes a M98 or M99 was not found
079
Memorized program and tape contents do not coincide
085
When storing data in memory by using ASR or RS232C interface, an over-run or framing error was generated
086
The signal level of RS232C interface was incorrect
087
When storing data in the memory by using the Fanuc RS232 interface, the time required to store the data is insufficient.
090
The reference point return cannot be performed normally because the reference point return start point is to close to the reference point or one revolution signal is not input owing to a fault in the pulse coder.
091
Reference point return cannot be executed normally, because of the feedrate is too low to synchronise the one revolution signal of the pulse coder with the reference counter,
092
The axis designated by G27 did not return to reference point.
094
No P type can be specified for program restart (because after program interruption, coordinate system setting or ORIGIN, etc. was executed)
095
No P type can be specified for program restart (because after program interruption, external work zero point offset value changed)
096
No P type can be specified for program restart (because after program interruption, work zero point offset value changed).
097
No P type can be specified for program restart (because after program interruption, no automatic operation has been executed).
100
The switch to set parameters is on. Push the reset button after turning off the switch.
101
The power was turned off while rewriting the contents of memory in the part program storage & editing operation. When this alarm is generated you must turn on the power while pushing the DELETE and RESET buttons to clear the memory.
110
Absolute value of data of fixed point representation exceeds the upper bound (99999999).
111
Exponent of data of floating point representation exceeds the upper bound.
112
Divisor is 0
113
A function that cannot be used by user macro A is used
114
Format error except for
115
Value not defined as variable number is assigned
116
Left side of substituted sentence is a variable of prohibited substitution
118
Nesting of brackets exceeds the upper limit (5).
119
Argument of SQRT is negative , Or argument of BCD is negative
122
Nesting of macro exceeds the upper limit (4)
123
Macro control command is uded in tape mode
124
DO END is not 1:1 corresponding
125
Format error of (formula)
126
Not 1 £ n £ 3 in DO n
127
NC command and macro command are mixed
128
Not 0 £n £9999 in GO TO n
129
Unallowable address is used in .
130
In external data input, greater-address data contains an error
131
In external alarm message, five or more alarms have occurred
132
In external alarm message, clear, no corresponding alarm number exsists
133
In external alarm message and in external operator message, smaller- address data contains an error
170
Programs of numbers 8000 – 8999 and 9000 – 9899 are being edited, But this alarm occurs only when parameter setting inhibits these programs to be edited.
Error on Stroke Limit Switch
210
The movable part of machine touched the X Axis plus stroke limit switch
211
The movable part of machine touched the X Axis minus stroke limit switch
212
While the X Axis was moving in the plus direction, It entered into the forbidden area of the stored stroke limit 1
213
While the X Axis was moving in the minus direction, It entered into the forbidden area of the stored stroke limit 1
214
While the X Axis was moving in the plus direction, It entered into the forbidden area of the stored stroke limit 2
215
While the X Axis was moving in the minus direction, It entered into the forbidden area of the stored stroke limit 2
220
The movable part of the machine touched the Y axis plus stroke limit switch
221
The movable part of the machine touched the Y axis minus stroke limit switch.
222
While the Y axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 1
223
While the Y axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 1
224
While the Y axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 2
225
While the Y axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 2
230
The movable part of the machine touched the Z axis plus stroke limit switch
231
The movable part of the machine touched the Z axis minus stroke limit switch
232
While the Z axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 1
233
While the Z axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 1
234
While the Z axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 2
235
While the Z axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 2
240
The movable part of the machine touched the 4th axis plus stroke limit switch
241
The movable part of the machine touched the 4th axis minus stroke limit switch
Error on servo system
400
The control received the X, Y or Z axis overload signal
401
The READY signal (VRDY) of the X, Y or Z axis velocity control has turned off
402
The control received the 4TH axis overload signal
403
The READY signal (VARY) of the 4TH axis velocity control has turned off
404
The READY signal (VARY) of the X, Y or Z axis velocity control does not turn off even though the READY signal (PRDY) of the position control has turned off
The READY signal (VARY) of velocity control already on even though the READY signal (PRDY) of the position control is off yet at power on condition
405
In reference point return, reference point return is not performed in correctly by abnormality of NC control section or servo system. Perform manual reference point return again
410
The content of error register of the X axis is larger than the value allowed while the machine is stopped
411
The content of error register of the Y axis is larger than the value allowed while the machine is moving
412
Drift in X axis is excessive. (Exceeds 500VELO)
413
The content of the error register of the X axis exceeded =32767. Or the velocity command value of the DA converter is out of the range of +8191~ - 8192. Incorrect settings will cause this alarm
414
The resolver/inductosyn position detecting system of X axis is trouble
415
A feed rate exceeding 511875 detection units/sec was commanded in the X axis
An incorrect setting of CMR causes this error
416
X axis pulse coder position feedback is abnormal. (Disconnection alarm)
420
The content of the error register of the Y axis is larger than the value allowed while the machine is stopped
421
The content of the error register of the Y axis is larger than the value allowed while the machine is moving
422
Drift in Y axis is excessive. (Exceeds 500VELO)
423
The content of the error register of the Y axis exceeded =32767. Or the velocity command value of the DA converter is out of the range of +8191~ - 8192. Incorrect settings will cause this alarm
424
The DSCG position detecting system of the Y axis is trouble
425
A feed rate exceeding 511875 detection units/sec was commanded in the Y axis
An incorrect setting of CMR causes this error
426
Y axis Fanuc pulse coder position feedback is abnormal. (Disconnection alarm)
430
The content of the error register of the Z axis is larger than the value allowed while the machine is stopped
431
The content of the error register of the Z axis is larger than the value allowed while the machine is moving
432
Drift in Z axis is excessive. (Exceeds 500VELO)
433
The content of the error register of the Z axis exceeded =32767. Or the velocity command value of the DA converter is out of the range of +8191~ - 8192. Incorrect settings will cause this alarm
434
The resolver/inductosyn position detecting system of Z axis is trouble
435
A feed rate exceeding 511875 detection units/sec was commanded in the Z axis
An incorrect setting of CMR causes this error
436
Z axis pulse coder position feedback is abnormal. (Disconnection alarm)
440
The content of the error register of the 4TH axis is larger than the value allowed while the machine is stopped
441
The content of the error register of the 4TH axis is larger than the value allowed while the machine is moving
442
Drift in 4TH axis is excessive. (Exceeds 500VELO)
443
The content of the error register of the 4THaxis exceeded =32767. Or the velocity command value of the DA converter is out of the range of +8191~ - 8192. Incorrect settings will cause this alarm
444
The resolver/inductosyn position detecting system of the 4TH axis is trouble
425
A feed rate exceeding 511875 detection units/sec was commanded in the 4TH axis
An incorrect setting of CMR causes this error
426
Additional axis pulse coder position feedback is abnormal. (Disconnection alarm)
Connection alarm between each PCB
600
Data transferring error took place in the connection unit or in PC-model C
601
Slave relay was turned off. (Connections among unit, MDI/DPL (MDI/CRT) and master PCB are trouble. Another case change connection unit)
602
PC program has not yet been loaded
603
The correspondence between NC and PC is incorrect or interrupted. Change power sequence control PCB or master PCB
604
No hold is effective to PC-model B side MPU
605
A system error has occurred in PC-model B side MPU
606
RAM/ROM parity has occurred in PC-model B side MPU
607
Data transferring error took place in Fanuc MDI & CRT
Overheat alarm
700
Overheat of the master PCB
701
Overheat of the PCB for 4TH axis
702
Overheat of DC motor for X, Y, Z axis
703
Overheat of DC motor for 4TH axis
Errors on memory
900
Fault in bubble device. (Fault of input signal for bubble device)
901
Fault in bubble device. (The initial point in the bubble was not detected immediately after power on)
902
Fault in bubble device. (Page size error, undefined command)
903
Fault in bubble device. (Transfer missing, page size over)
904
Fault in Fanuc bubble device. (Parity error)
905
Fault in bubble device. (No marker)
906
Fault in bubble device. (Many defect loops)
910
RAM parity error (low byte)
911
RAM parity error (high byte)
920
System error (watch dog timer alarm)
930
CPU error (0, 3, 4 type interrupt generation)
997
ROM parity error (PC ROM)
998
ROM parity error (Basic ROM)
999
ROM pair error (No correspondence between high and low).

[yours_prabhat]

PARAM_INFO BIT_NO DESCRIPTN KEY
PARAM 000 1 T/M CIRC. INTER BY RAD.
PARAM 000 2 T/M ADD 16 OFFSETS MEMORY
PARAM 000 4 T/M CSS B (ANOLOG OUTPUT)
PARAM 000 5 T/M G20/G21 SWITCHING (INCH/METRIC)
PARAM 000 6 T/M REF. POINT RET'N (2ND) 6M 0 RETURN B
PARAM 000 7 T/M REF. POINT RET'N (1ST) 6M 0 RETURN A (MANUAL,G28
PARAM 001 0 T/M G90,92/94 CYCLES 6M ADDITIONAL AXIS @SIM CONTROL
PARAM 001 1 T/M AUTO TOOL COMP. 6M ADDITIONAL AXIS CONTROL
PARAM 001 2 T/M CHAM. AND CORNER RADIUS.6M SIM. 3 AXIS CONTROL
PARAM 001 3 T/M TOOL NOSE COMP. (RAD). 6M CUTTER COMP C
PARAM 001 5 T/M MULTI CYCLES. 6M S2/4-DIGIT BCD
PARAM 001 6 T/M M.P.GENERATOR
PARAM 002 0 T/M AUTO ACCEL/DECEL. FOR FEED
PARAM 002 1 T/M STORE STROKE LIMITS 2 AND 3
PARAM 002 2 T/M RADIUS PROGRAMMING 6M F1 DIGIT FEED
PARAM 002 3 T/M STORE STROKE LIMIT 1
PARAM 002 5 T/M ** TAPE INTERFACE
PARAM 002 6 T/M INCREMENTAL OFFSETS
PARAM 003 1 T/M G10 OPTION 6M OFFSET DATA FROM TAPE
PARAM 003 3 T/M ** ISO INPUT
PARAM 003 4 T/M CLOCK DISPLAY 6M RUN HOUR DISPLAY
PARAM 003 5 T/M RAPID TRAVERSE OVERRIDE
PARAM 003 7 T/M PC MODEL B.
PARAM 300 0 T MACRO A OPTION
PARAM 300 1 T MACRO B OPTION
PARAM 300 2 T RESTART IN PROGRAM
PARAM 300 3 T G31 SKIP (NO MOTION)
PARAM 300 4 T AUTO CO-ORD. SETTING.
PARAM 300 7 T ADDN. BLOCK DELETE
PARAM 301 1 T/M MESS DISPLAY.6M EXTERNAL DATA I/P, ALARM MSG
PARAM 301 2 T/M 80/320M MEMORY (PART PROGRAM STORAGE) 6M 125 PGM
PARAM 302 1 T/M VAR. LEAD THREADCUTTING 6M G60-UNIDIRECTION POSN
PARAM 302 2 T DIRECT I/P OFFSET VALUE
PARAM 302 3 T MIRROR IMAGE.
PARAM 302 6 T WORK CO-ORDINATE SETTING
PARAM 302 7 T OFFSET VALUE COUNTER I/P
PARAM 304 2 T TOOL WEAR/GEOM.
N0100 T/M SOME OPTIONS REQUIRE ADDN PROMS-MACRO
N0090 T/M SOME OPTIONS REQUIRE ADDN PROMS-TOOL WEAR/GEOM.
N0110 T/M BOARDS- MEMORY OPTIONS
N0019 T SETTING PARAMETER
N0020 T/M 1)PARAMETER WRITE ENABLE SWITCH "ON"
N0021 T MODE SWITCH TO "MDI" OR ESTOP STATE
N0015 TO CLEAR MEMORY POWER ON 'O'AND 'DELETE'KEYS
N0022 T HAND LOAD PARAMETERS 0- 4
N0023 T HAND LOAD PARAMETERS 300-302
N0024 T HAND LOAD PARAMETERS 310-313
N0025 T HAND LOAD PARAMETERS 340-341
PARAM 000 0 6M CIRCULAR INTERPOLATION STD G02 G03
PARAM 000 3 6M SPINDLE SPEED 12 BIT OUTPUT CSS A
PARAM 001 4 6M CUTTER COMPENSATION B
PARAM 001 7 6M TWO DIGIT DESIGNATORS T2/T4 TOOL FUNCTIONS
PARAM 002 7 6M EXTERNAL DECELERATION
PARAM 003 2 6M HELICAL INTERPOLATION
PARAM 002 4 6M THREADING AND SYNCROUS FEED
PARAM 003 0 6M PART PROGRAM CHECKING
PARAM 003 6 6M STORED PITCH ERROR COMPENSATION
PARAM 004 0 M TOOL LENGTH COMP. (G43,G44,G49)
PARAM 004 1 M TOOL OFFSET (G45,G48)
PARAM 004 2 M CANNED CYCLES B (G73,G74,G80-G89)
PARAM 004 3 M CANNED CYCLES A (G80,G81,G83,G84,G85,G86,G89)
PARAM 004 4 M CIRCULAR CUTTING
PARAM 004 6 M SND AUXILARY FUNCTIONS B-CODE 3 DIDGITS
PARAM 004 7 M REMOTE TYPE POSITION DISPLAY
PARAM 005 0 M EXTERNAL WORK NO. SELECT
PARAM 005 1 M
PARAM 005 2 M
PARAM 005 3 M TURRET INDEXING FUNCTIONS
PARAM 005 4 M FT CENTRE H ATC SPECIAL ATTACHMENT
PARAM 005 5 M FT CENTRE D/E ATS SPECIAL ATTACHMENT
PARAM 005 6 M ROBOT INTERFACE
PARAM 005 7 M NIBBLING CYCLE (WOODPECKER)
N0009 CONTROL
N0011
N0016
PARAM 004 5 M SCALE FUNCTIONS (MAGNESYNE-OPTISYS)
N0026 ** CHECK SETTING DATA ISO/EIA ETC. **
N0026 T/M

PARAM 300 6 M 3RD/4TH REFERENCE POINT RETURN
PARAM 300 5 M TOOL LIFE MANAGEMENT CONTROL
PARAM 301 0 M AUTOMATIC OVERRIDE
PARAM 302 0 M WORK COORINATE SYSTEM SETTING - G54-G59
PARAM 000 1 T/M CIRC. INTER BY RAD.
PARAM 000 2 T/M ADD 16 OFFSETS MEMORY
PARAM 000 4 T/M CSS B (ANOLOG OUTPUT)
PARAM 000 5 T/M G20/G21 SWITCHING (INCH/METRIC)
PARAM 000 6 T/M REF. POINT RET'N (2ND) 6M 0 RETURN B
PARAM 000 7 T/M REF. POINT RET'N (1ST) 6M 0 RETURN A (MANUAL,G28
PARAM 001 0 T/M G90,92/94 CYCLES 6M ADDITIONAL AXIS @SIM CONTROL
PARAM 001 1 T/M AUTO TOOL COMP. 6M ADDITIONAL AXIS CONTROL
PARAM 001 2 T/M CHAM. AND CORNER RADIUS.6M SIM. 3 AXIS CONTROL
PARAM 001 3 T/M TOOL NOSE COMP. (RAD). 6M CUTTER COMP C
PARAM 001 5 T/M MULTI CYCLES. 6M S2/4-DIGIT BCD
PARAM 001 6 T/M M.P.GENERATOR
PARAM 002 0 T/M AUTO ACCEL/DECEL. FOR FEED
PARAM 002 1 T/M STORE STROKE LIMITS 2 AND 3
PARAM 002 2 T/M RADIUS PROGRAMMING 6M F1 DIGIT FEED
PARAM 002 3 T/M STORE STROKE LIMIT 1
PARAM 002 5 T/M ** TAPE INTERFACE
PARAM 002 6 T/M INCREMENTAL OFFSETS
PARAM 003 1 T/M G10 OPTION 6M OFFSET DATA FROM TAPE
PARAM 003 3 T/M ** ISO INPUT
PARAM 003 4 T/M CLOCK DISPLAY 6M RUN HOUR DISPLAY
PARAM 003 5 T/M RAPID TRAVERSE OVERRIDE
PARAM 003 7 T/M PC MODEL B.
PARAM 300 0 T MACRO A OPTION
PARAM 300 1 T MACRO B OPTION
PARAM 300 2 T RESTART IN PROGRAM
PARAM 300 3 T G31 SKIP (NO MOTION)
PARAM 300 4 T AUTO CO-ORD. SETTING.
PARAM 300 7 T ADDN. BLOCK DELETE
PARAM 301 1 T/M MESS DISPLAY.6M EXTERNAL DATA I/P, ALARM MSG
PARAM 301 2 T/M 80/320M MEMORY (PART PROGRAM STORAGE) 6M 125 PGM
PARAM 302 1 T/M VAR. LEAD THREADCUTTING 6M G60-UNIDIRECTION POSN
PARAM 302 2 T DIRECT I/P OFFSET VALUE
PARAM 302 3 T MIRROR IMAGE.
PARAM 302 6 T WORK CO-ORDINATE SETTING
PARAM 302 7 T OFFSET VALUE COUNTER I/P
PARAM 304 2 T TOOL WEAR/GEOM.
N0100 T/M SOME OPTIONS REQUIRE ADDN PROMS-MACRO
N0090 T/M SOME OPTIONS REQUIRE ADDN PROMS-TOOL WEAR/GEOM.
N0110 T/M BOARDS- MEMORY OPTIONS
N0019 T SETTING PARAMETER
N0020 T/M 1)PARAMETER WRITE ENABLE SWITCH "ON"
N0021 T MODE SWITCH TO "MDI" OR ESTOP STATE
N0015 TO CLEAR MEMORY POWER ON 'O'AND 'DELETE'KEYS
N0022 T HAND LOAD PARAMETERS 0- 4
N0023 T HAND LOAD PARAMETERS 300-302
N0024 T HAND LOAD PARAMETERS 310-313
N0025 T HAND LOAD PARAMETERS 340-341
PARAM 000 0 6M CIRCULAR INTERPOLATION STD G02 G03
PARAM 000 3 SPINDLE SPEED 12 BIT OUTPUT CSS A
PARAM 001 4 6M CUTTER COMPENSATION B
PARAM 001 7 6M TWO DIGIT DESIGNATORS T2/T4 TOOL FUNCTIONS
PARAM 002 7 6M EXTERNAL DECELERATION
PARAM 003 2 6M HELICAL INTERPOLATION
PARAM 002 4 6M THREADING AND SYNCROUS FEED
PARAM 003 0 6M PART PROGRAM CHECKING
PARAM 003 6 6M STORED PITCH ERROR COMPENSATION
PARAM 004 0 M TOOL LENGTH COMP. (G43,G44,G49)
PARAM 004 1 M TOOL OFFSET (G45,G48)
PARAM 004 2 M CANNED CYCLES B (G73,G74,G80-G89)
PARAM 004 3 M CANNED CYCLES A (G80,G81,G83,G84,G85,G86,G89)
PARAM 004 4 M CIRCULAR CUTTING
PARAM 004 6 M SND AUXILARY FUNCTIONS B-CODE 3 DIDGITS
PARAM 004 7 M REMOTE TYPE POSITION DISPLAY
PARAM 005 0 M EXTERNAL WORK NO. SELECT
PARAM 005 1 M
PARAM 005 2 M
PARAM 005 3 M TURRET INDEXING FUNCTIONS
PARAM 005 4 M FT CENTRE H ATC SPECIAL ATTACHMENT
PARAM 005 5 M FT CENTRE D/E ATS SPECIAL ATTACHMENT
PARAM 005 6 M ROBOT INTERFACE
PARAM 005 7 M NIBBLING CYCLE (WOODPECKER)
N0009 CONTROL
N0011
N0016
PARAM 004 5 M SCALE FUNCTIONS (MAGNESYNE-OPTISYS)
N0026 ** CHECK SETTING DATA ISO/EIA ETC. **
N0026 T/M

PARAM 300 6 M 3RD/4TH REFERENCE POINT RETURN
PARAM 300 5 M TOOL LIFE MANAGEMENT CONTROL
PARAM 301 0 M AUTOMATIC OVERRIDE
PARAM 302 0 M WORK COORINATE SYSTEM SETTING - G54-G59

[vanwyksc]

Did you find the manuals for 6T B?

[mflux_gamblej]

yes fanuc sells a brand new un-used hardcopy for $35 + shipping. It was in pristine condition and arrived in a foam lined box. do not bother with buying it from PDF people (the 6T is not available like that anyway).

[vanwyksc]

I am happy that you are sorted.
I was looking for a manual myself, but Fanuc South Africa told me it is no more available and that they can scan one for me and that it will cost a small fortune.
I manage to loan one from someone and got it scanned myself and saved it into a PDF file.
The book is a bit mishandled but it is ok to use.
Did you buy it from Fanuc in USA?

[KQHung]

Hallo Mflux_Gamblej,

can you send me a copy of fanuc 6T and fanuc 11T? Thank you very much!

Best regards,

Hung from Vietnam

[fizzissist]

Hallo Mflux_Gamblej,

can you send me a copy of fanuc 6T and fanuc 11T? Thank you very much!

Best regards,

Hung from Vietnam

.... While you're at it, can you send me some fishing poles, a couple of cases of beer, and.... oh yeah.... a bass boat?

[chauanlac]

thank for share alarm list.

[machinehop5]

.... While you're at it, can you send me some fishing poles, a couple of cases of beer, and.... oh yeah.... a bass boat?

now thats funny...