545,767 active members*
1,816 visitors online*
Register for free
Login
Results 1 to 6 of 6
  1. #1
    Registered
    Join Date
    Dec 2011
    Posts
    34

    Parrellel and com port?

    im having a problem with the port im using that is suppose to connect the Break out board to the computer. ive used 2 older computers to connect to the BOB using mach3 and it did fine. the 2 older computers had the 25 pin port on board the mother board. Now i want to use a newer computer to run my cnc machine but it didnt have the 25 pin connector so i bought a "parrallel port" to put into my new computer to connect to the BOB but it still doesnt work. I noticed that in mach3 the port is labeled "com" and in my hardware settings the port that i installed is a "lpt" is their a way to change this or is "com" and "lpt" port 2 different types.

  2. #2
    Registered
    Join Date
    Jan 2012
    Posts
    394
    From my understanding, newer computers without a parallel port on board the motherboard or Laptops have a problem sending the information to the breakout board.

    You may need to purchase an Ethernet or USB smooth stepper. They are about $185.

    A Smooth stepper is the way to go anyway. Much faster, and it will allow you to connect multiple Breakout boards so you can run 6-axis if you want. (i think, i'm still reading up on them).

  3. #3
    Gold Member
    Join Date
    Apr 2006
    Posts
    3498
    UC100 or UC300 from cncdrive is a good option too.
    http://free3dscans.blogspot.com/ http://my-woodcarving.blogspot.com/
    http://my-diysolarwind.blogspot.com/

  4. #4
    Member
    Join Date
    Dec 2004
    Posts
    1316
    Not all cards work correctly. They need to be an EPP compatible parallel port card.

    Below is a link. You can also look for other links related to CNC applications.

    Parallel Port I/O PCI Card for PC | MyDIYCNC - Home of the DIY Desktop CNC Machine

  5. #5
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Posts
    35475
    You don't use the com port in Mach3 for running your machine. It can only be used for sending serial commands, which would be a custom feature added by the user.

    If you added a parallel port, it's important that you have the port address correct on the Ports and Pins screen.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)

  6. #6
    Registered
    Join Date
    Oct 2013
    Posts
    7
    I'm having a similar problem. I was using an old desktop, & it worked fine. I had a rapid clicking...phzzz...pop...phzzz...stop. Bugger.
    After a lot of figuring, it's the parallel port. I bought another PCI board with minimal components (looks like just one main chip), connected up, and nothing but problems. One stepper motor almost removed my fingerprints, it got up to 80 degrees C!
    Turns out it must be the problem you've addressed (it still works fine on an old laptop), I need to configure it to EPP, & I have no idea how to do that. Can it be re-configured, or is it the board itself (i.e. need to replace).
    Any ideas?
    TIA

Similar Threads

  1. rs232 port usb port question
    By beekeeper in forum Controller & Computer Solutions
    Replies: 3
    Last Post: 09-24-2010, 09:36 PM
  2. Need Another Port in BOB
    By Mr.Chips in forum General CNC (Mill / Lathe) Control Software (NC)
    Replies: 4
    Last Post: 08-25-2009, 03:58 AM
  3. Paraller Port Driver - Breakout Port
    By billy in forum General CNC Machine Related Electronics
    Replies: 7
    Last Post: 11-20-2008, 02:27 PM
  4. How do I put in an SAE #6 port?
    By Driftwood in forum General MetalWork Discussion
    Replies: 4
    Last Post: 10-25-2008, 08:10 PM
  5. USB port
    By fourperf in forum Haas Mills
    Replies: 4
    Last Post: 02-03-2008, 01:00 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •