[cnchero11]

Hello people

I have the following problem. On my machine the preset table is not enabled or not activated. Therefore I wanted to work with the zero-point table because nothing else is possible. Now I approach my first part and after the machine asked me ACTUAL VALUE or REFERENCE I set it to reference value. But now when approaching my second part and set this to zero point number 2 (the same procedure as in the first part)- then the program always jumps to the second part and not as it should to the first one and then the second after.

I am in desperation!

Thanks in advance

Best regards

[Klartext]

let's see how you've programmed it

usually you can unlock the Presettabelle (in the MPs, but simply call Heidenhain) wink.gif

[General-5Achs]

So it worked in the end.
I just do not understand why I cannot work with the reference values. After my colleague went home, I have tried everything...
I had never worked with the zero point.d before- only with the preset table or just with encapsulated zero points itself. That always worked well but new company new requirements...

The thing is, I set the reference point X0 Y0 Z0 to the left part of the piece and then to comlumn1 in the table ( Current value)
Then I just touched the right part in the same way with reference point X0 Y0 Z0 and wrote it into row 2 in the table (current value)
Is this the right course of action?
It worked but I still think it's awkward.
The Preset table should there be, according to the HDH, software version is 09SP1 340 423 but it must be unlocked first. However it’s a DMG machine and therefore I am referred by HDH to DMG.
I haven‘t called yet due to a lack of time.
Attached the program (and the associated table) as I thought it would be cobbled together.
PLEASE JUDGEMENTS!

PS:
Below the table
BEGIN ZERO POINT.D MM
D X Y Z A B C W D L DOC
0 +0 +0 +0 +0 +0 +0 +0 +0 +0
1 +0 +0 +0 +0 +0 +0 +0 +0 +0
2 +253.9959 +0 +0.1459 +0 +0 +0 +0 +0 +0
3 +0 +0 +0 +0 +0 +0 +0 +0 +0
4 +0 +0 +0 +0 +0 +0 +0 +0 +0
5 +0 +0 +0 +0 +0 +0 +0 +0 +0
6 +0 +0 +0 +0 +0 +0 +0 +0 +0
7 +0 +0 +0 +0 +0 +0 +0 +0 +0
8 +0 +0 +0 +0 +0 +0 +0 +0 +0
9 +0 +0 +0 +0 +0 +0 +0 +0 +0
10 +0 +0 +0 +0 +0 +0 +0 +0 +0
11 +0 +0 +0 +0 +0 +0 +0 +0 +0
12 +0 +0 +0 +0 +0 +0 +0 +0 +0
13 +0 +0 +0 +0 +0 +0 +0 +0 +0
14 +0 +0 +0 +0 +0 +0 +0 +0 +0
15 +0 +0 +0 +0 +0 +0 +0 +0 +0
16 +0 +0 +0 +0 +0 +0 +0 +0 +0
17 +0 +0 +0 +0 +0 +0 +0 +0 +0
18 +0 +0 +0 +0 +0 +0 +0 +0 +0
19 +0 +0 +0 +0 +0 +0 +0 +0 +0
20 +0 +0 +0 +0 +0 +0 +0 +0 +0
21 +0 +0 +0 +0 +0 +0 +0 +0 +0
22 +0 +0 +0 +0 +0 +0 +0 +0 +0
23 +0 +0 +0 +0 +0 +0 +0 +0 +0
24 +0 +0 +0 +0 +0 +0 +0 +0 +0
25 +0 +0 +0 +0 +0 +0 +0 +0 +0
26 +0 +0 +0 +0 +0 +0 +0 +0 +0
27 +0 +0 +0 +0 +0 +0 +0 +0 +0
28 +0 +0 +0 +0 +0 +0 +0 +0 +0
29 +0 +0 +0 +0 +0 +0 +0 +0 +0
30 +0 +0 +0 +0 +0 +0 +0 +0 +0
31 +0 +0 +0 +0 +0 +0 +0 +0 +0
32 +0 +0 +0 +0 +0 +0 +0 +0 +0
33 +0 +0 +0 +0 +0 +0 +0 +0 +0
34 +0 +0 +0 +0 +0 +0 +0 +0 +0
35 +0 +0 +0 +0 +0 +0 +0 +0 +0
36 +0 +0 +0 +0 +0 +0 +0 +0 +0
37 +0 +0 +0 +0 +0 +0 +0 +0 +0
38 +0 +0 +0 +0 +0 +0 +0 +0 +0
39 +0 +0 +0 +0 +0 +0 +0 +0 +0
40 +0 +0 +0 +0 +0 +0 +0 +0 +0
41 +0 +0 +0 +0 +0 +0 +0 +0 +0
42 +0 +0 +0 +0 +0 +0 +0 +0 +0
43 +0 +0 +0 +0 +0 +0 +0 +0 +0
44 +0 +0 +0 +0 +0 +0 +0 +0 +0
45 +0 +0 +0 +0 +0 +0 +0 +0 +0
46 +0 +0 +0 +0 +0 +0 +0 +0 +0
47 +0 +0 +0 +0 +0 +0 +0 +0 +0
48 +0 +0 +0 +0 +0 +0 +0 +0 +0
49 +0 +0 +0 +0 +0 +0 +0 +0 +0
50 +0 +0 +0 +0 +0 +0 +0 +0 +0
[END]

[Kai-K]

Hello
SEL TABLE ZERO POINT.D
is missing

[General-5Achs]

????????????????????

Can you be a bit more specific.. preferably with an example program

[Kai-K]

0 BEGIN CALL PGM MM
1 CYCL DEF 7.0 DATE
CYCL DEF 7.1 x 2 +0
CYCL DEF 7.2 Y 3 +0
4 CYCL DEF 7.3 +0 Z
TABLE 5 SEL "NEUTRAL POINT.D"
6 CYCL DEF 7.0 DATE
7 CYCL DEF 7.1 # 1
8 CALL PGM ELECTRODE3.H
9 CYCL DEF 7.0 DATE
10 CYCL DEF 7.1 x +0
11 CYCL DEF 7.2 Y +0
12 CYCL DEF 7.3 +0 Z
13 L Z +200 R0 FMAX
14 M0
15 M13
16 CYCL DEF 7.0 DATE
17 CYCL DEF 1.7 # 2
18 CALL PGM ELECTRODE3.H
19 CYCL DEF 7.0 DATE
20 CYCL DEF 7.1 x +0
21 CYCL DEF 7.2 Y +0
22 CYCL DEF 7.3 +0 Z
23 L Z +200 R0
24 M30
25 MM END CALL PGM

You first have to activate the table

[General-5Achs]

Yes ok, I had activated it manually- The button SEL is completely unknown to me.

Where can I enter the table ??? One can never stop learning..

[Kai-K]

softkey
Program Preferences -> Zero Table