586,096 active members*
3,741 visitors online*
Register for free
Login
Results 1 to 11 of 11
  1. #1
    Join Date
    Apr 2005
    Posts
    903

    Haas control beeper

    Is there a setting for the beeper loudness on an '08 VF2? The pitch is so loud I swear it's going to split my skull in half. I wear ear protection and try to keep the door closed. Also covered the little speaker with duct tape but then you can't hear it at all. Just hoping there is a speaker setting.
    2008 Haas VF2D
    OneCNC XR5 Mill Expert

  2. #2
    Join Date
    Mar 2010
    Posts
    1852

    Re: Haas control beeper

    You can turn it off at setting #39 I think, but no volume change I believe.

    Mike
    Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28

  3. #3
    Join Date
    Jul 2014
    Posts
    26

    Re: Haas control beeper

    Quote Originally Posted by l u k e View Post
    Is there a setting for the beeper loudness on an '08 VF2? The pitch is so loud I swear it's going to split my skull in half. I wear ear protection and try to keep the door closed. Also covered the little speaker with duct tape but then you can't hear it at all. Just hoping there is a speaker setting.
    How about the ducttap wit w pin hole or 12...

    Sent from my Nexus 5 using Tapatalk

  4. #4
    Join Date
    Mar 2003
    Posts
    927

    Re: Haas control beeper

    On some Haas' the beeper/speaker cover actually turns to change the volume..Kind of like the air vent on the dash of your car. might try that.
    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)

  5. #5
    Join Date
    Apr 2005
    Posts
    903

    Re: Haas control beeper

    Looks like I will just have to improvise...
    2008 Haas VF2D
    OneCNC XR5 Mill Expert

  6. #6
    Join Date
    Mar 2010
    Posts
    1852

    Re: Haas control beeper

    Hooah!
    Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28

  7. #7
    Join Date
    Apr 2005
    Posts
    903

    Re: Haas control beeper

    I would have much rather had a control setting.
    2008 Haas VF2D
    OneCNC XR5 Mill Expert

  8. #8
    Join Date
    Mar 2012
    Posts
    52

    Re: Haas control beeper

    tried asking Hass ??

  9. #9
    Join Date
    Apr 2005
    Posts
    903

    Re: Haas control beeper

    Quote Originally Posted by wms View Post
    On some Haas' the beeper/speaker cover actually turns to change the volume..Kind of like the air vent on the dash of your car. might try that.
    On closer inspection there is a shutter over the speaker. When I first checked I was trying to turn the whole face but you have to turn the tip, works great! Thanks.
    2008 Haas VF2D
    OneCNC XR5 Mill Expert

  10. #10
    Join Date
    Mar 2010
    Posts
    1852

    Re: Haas control beeper

    Could have been worse. I ran an older VF-0 once on which the alarm sounded like a very sick cat meowing. That was REALLY irritating.

    Mike
    Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28

  11. #11
    Join Date
    Jul 2014
    Posts
    1

    Re: Haas control beeper

    no control on volume in setting, you can adjust volume on speaker, by turning cover on speaker,.......its hart to find it but if you do its working great..

Similar Threads

  1. HAAS BEEPER
    By PROCEL in forum Haas Mills
    Replies: 9
    Last Post: 03-09-2011, 05:40 AM
  2. New Haas control help please
    By hercules in forum Haas Lathes
    Replies: 5
    Last Post: 07-28-2009, 04:52 PM
  3. New Haas sl20 control
    By bullseye in forum Haas Lathes
    Replies: 35
    Last Post: 04-16-2008, 02:39 PM
  4. haas servo control
    By heartlnd in forum Haas Mills
    Replies: 0
    Last Post: 02-11-2007, 01:04 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •