[Spinner]

Hi
Just got a Hitachi Seiko 1987 machine with a Fanuc 6M controller with a few manuals missing. Anyone know where these may be downloaded from. The main ones would be Maintenance and programing.
Cheers

[Wjman]

Hi,
Just read your post about the Hitachi machine. We currently have 6 large Hitachis A 5Q, 4 6Q's, and an 8Q not sure about the control off the top of my head but if you get back to me with the machine model etc I'll see if I can help. BTW we are based in Redditch, near Birmingham.
www.harperandsimmons.co.uk
Mark...

[Spinner]

Hi
Thanks for the reply. It's an old machine (manual Z) that runs ok but we are having a few problems that should be easy to correct if we had the manuals. I have ran Sodicks and Charmilles before but not one of these so I'm doggy paddling by trial and error for now. A maintanance manual would help lots.

Machine: 1987 Hitachi Seiko
Control : Fanuc System 6M

Cheers

[Wjman]

Hi again,
Without knowing your problems I cannot help you, because obviously we need our manuals, but if you can explain your problems we maybe able to help.you see the thing is basically the machines are all the same but some have different guides, power supplies, power pickups etc. we all have various experience with Sodicks, Agie, Charmilles, Mitsubishi, Japax, so we could possibly help you without giving away our manuals (we could fax copies of what you need however) failing that we could put you in touch with the uk dealer who also maybe able to help.
yours Mark...

[Qdptech]

I also have just purchased a Hitachi Wire EDM at an auction. I do not have any manuals either and I am looking for some manuals. I have been trying to order some from Hitachi but they seem very slow to respond.

1987 Hitachi Hi-Cut 203 with Fanuc 6M controller.
I am willing to pay money for a copy of any of the manuals.
Thanks for any help.
Troy

[Spinner]

Hi
Sorry for the delay, I have to work these pages from home.
Firstly we seem to be getting away with a very simple program setup.
G21 G90 G50
G41 D0
X_____ Y_____
Same for the 4 axis. I could do with a list of relavent G codes if you have them as I think some may be missing.
Secondly If we get an alarm 41 (offset issue) it would appear that we can't override, the program seems to miss a few lines before continuing. I was thinking a parrameter needed setting.
Thirdly how is the wire tension adjusted. There seems to be no manual adjustment just thread it and run, I know it's old but.....

If you can help with any of these issues we would be very grateful.

Cheers and thanks.

[Klox]

Hi Guys, I know someone at hitachi that would be able to help you with the relevant manuals. Unfortunately i have relocated toNZ recently and all my stuff is somewhere in the middle of the indian ocean in a shipping container. If you guys can wait until end of january i will gladly help....

Klox

[Arturo Chavez]

Hi

I have a Japax/Bridgeport wire EDM I believe is an '84 or '85, but I'm missing all the manuals; Is there anyone that knows were I can download them, I need the programing and maintenance.
Your help is appreciated.

Arturo Chavez

[makinoravi]

i plan to purchase used hitachi hcut 203 wire edm.
machine is in good condition.

i need operating instructions for hitachi hcut 203m.
this is hitachi control system.
pls anyone gives step by step or mail may id [email protected] or
[email protected]

i need following details
1.how can create program.( ican create program from master cam)
2.how to transfer program through rs232.
3.how to input program in machine
4.possiable to load program through floppy drive.
5.in machine 3 floppy drive is there(these are software floppys).
6.how to go machine referenence after power on
7.how to take ref after setting.
8.how to do vertical alignmnt.
9.how to preset u and v after vertical alignment.
10.how to select the progrm for run.
11.how to give offsets in machine.
12.how to give multipasses.
13.how to select machine parameters(current,wire tension,wire feed,on time,off time etc)
14.pls give any one sample program(for straight cut 2 pass)
15.pls give program with taper(1pass)
16. in taper cut how to input reference height and z and angle.
pls help me anyone.

regards
ravindran.b