[wklaser]

Hi, my dear countrymen, let's build a good reputation for our products, and after service, and let customers all over the world love our Chinese lasers.

We are the manufactures specialzing in this line for many years, if someone need laser engraving cutting machines, kindly contact me by the following address:

[email protected]
[email protected]

Take a look at some of our models in the attachments.

:rainfro: :rainfro:

[bear08]

[bear08]

[vivinar]

Hope all you can like chinese machine.Becuase we try to make best quality and best service for you.

[Tweakie]

I constructed my own CNC / Laser machine and various parts were purchased from different countries around the world. The parts I did purchase from China were all excellent and well fit for their purpose.
I think you can be unlucky and purchase rubbish from your own country so come on Guys don't keep knocking China for poor quality - It isn't all bad.

Tweakie.

[Les101]

I believe my machine is very well made. The software is the problem. When you try to load the driver and software the computer wont allow it to because it has a worm virus. Lurka.A When I try support, they say its not a problem, others have said same thing, so just remove all defenses and load. I asked them for a clean disc without virus and nothing so far.

[Tweakie]

Hi Les,

Anti-virus protection programs take a ‘part code sequence’ from a known virus and look for that same ‘part code sequence’ in any new programs we attempt to load on our PC. If it finds a match then it is obviously a virus. What should be considered here is that whilst it is extremely unlikely for any bona-fide program to contain a part code sequence identical to a known virus it is not impossible. What does occur, however, is that anti-virus checkers also look for key words such as ‘crack’,’keygen’ etc, etc and if any of these words are found then again it is marked as a virus. There are language / grammar differences around the world, caused mainly by translation, and it is quite conceivable for any good program to contain words which an anti-virus treats as being bad. Now I am not saying that you don’t have a virus in your software but there is a more than even chance that a different virus checker will look at this software an see no problem with it. It’s almost worth running this software on an old PC just to see if there is a problem or not.

Just my personal opinion buddy. (you could be waiting a long time for another disk).

Tweakie.

[mlind]

LOL...

It isn't all bad just 99% of it. Plus it is probably painted with lead based paint...the same paint they use on toys....

Bottom line............China on the label mean scrap on the table.

Need I say more.

I constructed my own CNC / Laser machine and various parts were purchased from different countries around the world. The parts I did purchase from China were all excellent and well fit for their purpose.
I think you can be unlucky and purchase rubbish from your own country so come on Guys don't keep knocking China for poor quality - It isn't all bad.

Tweakie.

[Tweakie]

LOL...

It isn't all bad just 99% of it. Plus it is probably painted with lead based paint...the same paint they use on toys....

Bottom line............China on the label mean scrap on the table.

Need I say more.

Sorry but what you say is just NOT true and yes you do need to say more and fully justify your statements (experience not speculation please).


Tweakie.

[W3Driver]

LOL...

It isn't all bad just 99% of it. Plus it is probably painted with lead based paint...the same paint they use on toys....

Bottom line............China on the label mean scrap on the table.

Need I say more.

You become what you pay for, all over the world.
Sometimes, you hear people talk, you would think, that the chinese people should work for us in the Westside, without a chance of earning money, and should have nothing to live for.
What ive bought from them till today, was good Quality, (ask them for Quality, and not the cheapest Price) at acceptable Prices.
Please stay away with such common Statements, ore you should show here examples.

[NZCNC]

Hi there im interested in a laser scanner to fit on the head of our CNC router and scan can you advise of your experience

Tim

[bear08]

http://www.cnczone.com/forums/showthread.php?t=28278

[wklaser]

To Bear08:

Hi, you mean we are not the manufacturer?? Welcome you to come to China to visit our factory in your convenient time.. we are the manufacturer specializing in lasers for many years, that's sure.

Many thanks.

[wklaser]

some new pictures of our product, welcome to distribute them in your esteemed country:wave: :wave:

[Neil Pritchett]

Dear all,
we at CTRfuture http://www.ctrlasers.co.uk invested in 4 man weeks visiting Chinese laser manufacturers. Most of this time was with Redsail http://www.hflaser.com the one we were best pleased with, and now exclusively distribute in the UK.

We got a valuable insight as to the workings of the Chinese manufacturing industry during our visit. One of the main findings was that we discovered a lot of industrial espionage in China. Not just ripping off 'western designs' but also Chinese designs. Some of the plethora of 'cheap' laser manufacturers has been set up by people who once worked for Redsail. They are able to copy, all be it not including the finer points of design, but they do not necessarily have the development team to understand or create original designs and improve on existing products. This may explain some of the 'lack of support' issues.

Redsail, on the other hand, have taken on another five engineers this year (2007) to add to their existing team. Their development program is continuous and the level of interaction between us and them is solid. We have requests for improvements, they respond.
This has lead to a number of refinements to the existing range that you will not find in the competitive machines. At least, not until they have copied the ones they can see! Also, new machines are on their way very soon.

It is interesting that one of the pictures I have seen posted, originally in the fourth quarter last year, looked identical to one I saw in the development area of Redsail when I was there in November! The Redsail machine had been under development since the beginning of 2006. By Chinese standards this is a long time, which gives an indication of the stringent development and testing undertaken by Redsail. The down side of this is that it leaves them more open to design theft, as all someone needs to do is photograph the machine and, with the power of the internet, the recipient of the photo has a new machine on the market!
NOTE: the real machine is finally about to be released within the month, along with another that hasn't been stolen (yet).

No matter who's machine you buy, buy with your eyes open. Don't fall into the trap of being blinded by the price. Consider the full purchase and support.
Some will want to take the risk, and order direct. If this is your budget I wish you success; but consider that it may not work out that cheep.

You are taking risks with any purchase. just weigh them up carefully, list the pro's and con's and go with what you can afford when you need to buy.

Best regards. Neil

[wklaser]

Hi Neil,
Thanks for your comments.

But I want to clear:

There is a famous saying in Chinese: "Diamond cut diamond". Don't say one company is the best forever. I am much more familiar with Chinese laser company than you. There are too many companies that you have never visited.

If you say one company is the best in China, it's just your opion, and you have your own purpose. in fact, if you are the sole agent of one company, of course you will say that one is th best.

But just a suggestion for you if you don't mind, when you praise one company, don't say bad words on other companies, many thanks.

Diamond cut diamond~~~ Can you understand me ?? :violin:

[Neil Pritchett]

Hi Neil,
Thanks for your comments.

But I want to clear:

There is a famous saying in Chinese: "Diamond cut diamond". Don't say one company is the best forever. I am much more familiar with Chinese laser company than you. There are too many companies that you have never visited.

If you say one company is the best in China, it's just your opion, and you have your own purpose. in fact, if you are the sole agent of one company, of course you will say that one is th best.

But just a suggestion for you if you don't mind, when you praise one company, don't say bad words on other companies, many thanks.

Diamond cut diamond~~~ Can you understand me ?? :violin:

Dear WKLASER,
Yes the Diamond phrase is very good. I must have given the wrong impression if my posting indicated that Redsail has perfect products.
No company can be perfect in all things, and if they think that way then they would never try to improve.

You are also correct in saying that we did not visit all the laser manufacturers in China. This was not our goal. The trip took place after significant research to identify a number of companies who had certain qualities and attributes. There are differences between the way a company supports distributors and end users as I'm sure you are aware. This research was not exhaustive, that would have been an endless task! However, the companies chosen were ones with good products, good attitude, strong development and loyalty. There are perhaps other companies out there that also have these qualities, but we only needed to find the one we felt was best for us to work with to ensure we could offer a high level of support to our end users.

Please also understand 'Sole agent' does not mean that we are owned by them! Our hands are not tied. We are free to take on other manufacturers product ranges, but we have no need to do that as Redsail is performing excellently for us.
I hope this clarifies our goals and any misunderstandings.
Best regards. Neil

[MonoNeuron]

Hi all.
He probably didn't get your emails last time you sent one as there was an undersea ground movement just after Xmas that severed the communication link/cable. Try another mail now as it may be fixed by now. Some times s##t happens when you least want it to.
Richard.

[Pete Stenabaugh]

Hey all, I have been successful in contacting WKLaser. The rep I have spoke with (email) is Jack Yin. His email address is [email protected]. I have gotten a pretty good price from him on the LC1280 laser, along with some prices on some of the consumables. All the components are pretty reasonably priced.

I have also had several emails back and forth with another company on lasers, their web site is: http://www.whzt.com/zhongtai-e/productlist.asp?type=109.

The laser I looked at there is the ZTDQ12090 which is an 80W machine with a working area of 1200 x 900 mm. It is priced a bit higher than the unit from WKLaser, but still fairly reasonable. I am undecided as to which one I might eventually consider purchasing, but I need to confer with some friends to see, as we may purchase 2 or 3 units at the same time. The contact person at this company is Marsha, and here email address is: [email protected].
Marsha has been really great at replying on email. Send her a question and you will have your answer the next day - every time.

I have a friend who travels to China several times a year, so I am going to see if he can actually go and visit both of these companies and have a look see, maybe take a few photos if he is allowed, and report back his findings. I dont like to be skeptical, but I (we) are risking a fair amount of cash on machines and equipment that we are purchasing sight unseen, and it would be nice to have that warm and fuzzy feeling when we write cheques out of country. I dont dispute the reputation or existance of these companies at this time, as I have no reason to doubt them at all, but I would just like to know a bit more, so I get that warm and fuzzy......

I will keep this group posted as to any information that I am able to come up with.

Pete

[smz7073]

i want driver for pmc05 card with windows xp
:drowning: :drowning: