HI
Who used this board, does the backlash correction work? Can someone check?
HI
Who used this board, does the backlash correction work? Can someone check?
I also have the BL-USBMach-2.1
Have you been able to operate axis A or B as slaves? I work all the axes (X, Y, Z, A and B) individually but if I put the A or B as slaves the corresponding engines do not work.
On YouTube I've seen this video:
I see that he uses the 5 axes and 4 of them move at the same time. Mach3 uses a 6-axis screenset, but I do not see what version it is.
The Y axis of the CNC that I am building has two motors and I need to operate an axis in slave mode.
When I manage to configure the axes I will configure the control of the spindle.
Same problem with the slave axis. Can you connect the pulse of the x- axis to two drivers?
I have got this board working with drufelcnc with A as a slave of the Y axis. So it is a software issue as the MACH3 plugin does not do the slave. Drufel runs fine. The plugin authors need to update to get it working.
You can also just run Pulse, Dir and EN from the Y to the drivers for both Y and A and it works fine with Mach3
usbmove helped me too - Thanks!
This software for BL USB Mach3 V3.22
is OK
am use
Ok Try agian.
this Plugin
Is Config
Can't open the file
Hello,
I use the file BL USB Mach3 V3.22. I'm just testing with one driver/motor. It works but I noticed that it is actually limited to 85khz not 100khz (the kernel is set to 100mhz in the control plugin and in Mach3). But the thing that annoys me more is that it doesn't run at the specified rpm. My driver displays the rpm. I also tested a run of more than a minute to see which was wrong (the card or the driver) and it confirmed that the value displayed by the driver was correct. this problem occurs whatever the speed I try. It is never correct. It does the correct number of turns but not at the correct speed. There is no load attached to the motor just a small pulley (I could check that a turn was a turn and so on, meaning the configuration is ok).
so ive spent the last week trying to get this working, i NEED HELP PEASE!!!
using a v2.0 board, ive installed the settings as posted above. i can connect to the board as far as i know via mach3 i just cant make the motors move. ive tried every wiring configeration ive tried all pin numbers that i can think of and im out of ideas at this point.
any help would be extremely appreciated!!
if you want to control the spindle on this board using the supplied motor driver board supplied with this kit then. Use the port opposite the step control connections. de solder the variable resistor on the spindle driver board connect the middle 0-5v to pwm the negative to ground and the +5v to AV then go to spindle control n pins and ports and tick PWM control giving you stop start and speed for tools.. and stop on emergency stop.
you will then get Speed control with a max set in config spindle pully's,
mach3 plugin dll for USBMach V2 : come avete fatto per farla funzionare con window 10 , ci sono Drive , nel mio windos ci sono errori ..
we hee draive for windos 10
mach3 plugin dll for USBMach V2,, have drave for window 10 ,, we need drive,, in window 10 have not see drive very well
- - - Updated - - -
mach3 plugin dll for USBMach V2 : nave drive for window 10 , we cannot see , work deive in winsow 10
hi jeff, can you help me please?
BOBHiggins... so does this mean if you have the mach3 driver already installed you should uninstall it and install the usb driver ? Since the russian forum was talking about having trouble with that is that what they meant ? I have this board and it seems to make mach real glichy at times and I was wondering if that may be the problem . Too would you know about the inputs for this board , in mach3 the ports nad pins tab is setup for the printer port hence the name so how would 1 go about setting up inputs for the usb board ?