[gowthu]

Did anybody having ladder diagram for Moriseiki SL6 with Fanuc Controller 6T.I want the details to set the timer values as the values intialized.Please reply me.

Problem: Turret is not properly indexing and it is over shooting or not in reach to limitswitch to close the clamping confirmation signal.Problem observed after initailization of bubble memory due to alarm 901 & 904.Parameters reloaded and ok. only timers values not known.

[f-bu]

if you can not find it, post the plc chips here, I'll return in ladder text format

[vanwyksc]

if you can not find it, post the plc chips here, I'll return in ladder text format

Hi there
Can you get the ladder for 6TB if I give you the chip numbers?
Can I convert the Rom info buck into ladder?

[f-bu]

Hi there
Can you get the ladder for 6TB if I give you the chip numbers?
Can I convert the Rom info buck into ladder?

Sorry, just from the chip numbers, no. But from binary image of the chips, yes. You will need EPROM programmer to read the chips form PMC-model B board.
And usually I ask for $40 for making ladder text graphics file.

[vanwyksc]

Sorry, just from the chip numbers, no. But from binary image of the chips, yes. You will need EPROM programmer to read the chips form PMC-model B board.
And usually I ask for $40 for making ladder text graphics file.

Hi there

Someone did download the 6 EProms for me, but not the 902 chips.
Please send your email address then I can send you a picture of the board.
What program do you use to convert it from binary.
Have you got a example of one that you have done before?

[wahidbashir]

Hi f-bu,
we need ladder printout to diagnose an issue related to spindle fault and had done copy of plc eprom. Can you do it please.
here are attached bin files.

[baonam2019]

Hi f-bu,
we need ladder printout to diagnose an issue related to spindle fault and had done copy of plc eprom. Can you do it please.
here are attached bin files.

Have you converted to ladder yet?

[bk5]

I have the exact same problem on my Daewoo lathe w/6T control. How and where do you set timer values?

[memoryman]

To display the pc params press the param push button until top of screen says PC PARAM. Counters are params 2001,2002,2101,2102.
keep relays are 3001-3004. Timers are 1001-1019 in msecs. To change counters, turn program protect OFF.

[dbstream]

you may try these pc parameters settings
1006 = 100
1009 = 1000
1010 = 100
1014 = 8000
1015 = 100
3002 = 10000001 or 10010001
3003 = 01000000 for 10 stations turret or 10000000 for 12 stations turret.

Good Luck!

[bk5]

Thanks guys!

I found the PC paramenters. But there are values in there but I do not know which ones to adjust for my turret. I need to set timer 3,4,and 5, for the turret functions according to the fanuc manual. Right now the turret timers are way too high and every function of the turret takes about 5 seconds before it excecutes. The book says for example timer 3 set to 200ms. How does this value get entered in the PC parameters?
I also am not sure why the timers went high after the 904 alarm? you would think they would be zeroed out if anything. Thanks in advance for your help.

[vanwyksc]

Attachment 195868
Hi there
Find the picture attached. Can You do all of the chips?
What program do you use to convert it to the text layout?

[f-bu]

You have PLC model A, not B. Necessary chips are these 6 2716 on the right picture(two upper, 241&242 are system plc soft, but better copy them too)
set of programs needed, some my own made, some not

[vanwyksc]

Hi there

This is a 6T-B. The 6T-A the chips is on the main board. On the 6T-B the chips is on a ROM board that plugs into the main board. I have both type machines.
What do you use to convert the chips binary into the ladder diagrams.

[f-bu]

Hi there

This is a 6T-B. The 6T-A the chips is on the main board. On the 6T-B the chips is on a ROM board that plugs into the main board. I have both type machines.
What do you use to convert the chips binary into the ladder diagrams.

I wrote PLC model A, not the control, but the PLC

What do you use to convert the chips binary into the ladder diagrams.

see above: some my own made, some not

[Rocksalt]

you may try these pc parameters settings
1006 = 100
1009 = 1000
1010 = 100
1014 = 8000
1015 = 100
3002 = 10000001 or 10010001
3003 = 01000000 for 10 stations turret or 10000000 for 12 stations turret.

Good Luck!

Parameter 3003 is not correct above, at least for my machine (SL-3 Mori) 6T control. Bit 7 is on for a 10 position turret and off for a 12 position. Than again, this is all controlled by the ladder and can be changed.

[bk5]

PROBLEM SOLVED!!!! Thanks to your info I set the timers values and all is good. I answered my own question about which timer value from the manual coensides with what PC parameter. Timer 1 = 1001, 2 = 1002, etc. After the 904 alarm, all the timer values went to 6350. Does anyone now why? Are PC parameters backed up when I do a regular parameter back up?Thanks again for the help.

[eastcomms]

does the mori seiki sl-1 have a ladder screen to go to

[angelw]

does the mori seiki sl-1 have a ladder screen to go to

Not if the control is a Series 6. Machines equipped with this control were generally supplied with a Hard Copy of the Ladder logic. You may be lucky and still have a copy in the maintenance or wiring manual of the machine.

Regards,

Bill

[memoryman]

The eprom ladder data cannot normally be read. The PC parameters cannot be downloaded; write them down.