Hi all
Need help
When I do my motor tuning first manually, this I know how to do well and all the motors sound fast and responsive enough!
However when I then go and do the Steps per Unit in Mach3
The motors go far too slow and almost judder sounding
My question is how would you overcome this issue?
Results 1 to 5 of 5
-
09-06-2019, 12:56 PM #1
Banned
- Join Date
- Dec 2017
- Posts
- 53
STEPS PER UNIT MOTOR TUNING ISSUES
-
09-07-2019, 12:01 PM #2
Banned
- Join Date
- Dec 2017
- Posts
- 53
Re: STEPS PER UNIT MOTOR TUNING ISSUES
NO REPLYS? i try another forum
-
09-07-2019, 12:25 PM #3
Community Moderator
- Join Date
- Mar 2003
- Posts
- 35538
Re: STEPS PER UNIT MOTOR TUNING ISSUES
After you change the steps/unit, you need to change the acceleration and velocity settings.
Gerry
UCCNC 2017 Screenset
http://www.thecncwoodworker.com/2017.html
Mach3 2010 Screenset
http://www.thecncwoodworker.com/2010.html
JointCAM - CNC Dovetails & Box Joints
http://www.g-forcecnc.com/jointcam.html
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
-
09-07-2019, 01:05 PM #4
Banned
- Join Date
- Dec 2017
- Posts
- 53
Re: STEPS PER UNIT MOTOR TUNING ISSUES
Thank you ger21 for letting me know that, will try that, but i thought id done that as tried so many times! Maybe i kept going in the wrong order, will update! thanks again
-
09-07-2019, 02:20 PM #5
Community Moderator
- Join Date
- Mar 2003
- Posts
- 35538
Re: STEPS PER UNIT MOTOR TUNING ISSUES
How are you moving them? And are they going the correct distance?The motors go far too slow and almost judder soundingGerry
UCCNC 2017 Screenset
http://www.thecncwoodworker.com/2017.html
Mach3 2010 Screenset
http://www.thecncwoodworker.com/2010.html
JointCAM - CNC Dovetails & Box Joints
http://www.g-forcecnc.com/jointcam.html
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Reply With QuoteSimilar Threads
-
Dynamic steps per distance motor tuning?
By tgrandahl in forum Mach Software (ArtSoft software)Replies: 2Last Post: 05-21-2016, 06:57 PM -
Need Help for My X-axis motor tuning steps per and velocitY??
By mpix00 in forum Mini LatheReplies: 0Last Post: 01-18-2016, 02:41 PM -
Steps per inch in motor tuning (metric trapezoidal)
By SteveS in forum Mach Software (ArtSoft software)Replies: 0Last Post: 11-19-2015, 10:15 PM -
Motor Tuning, Going from Imperial TPI to Steps Per MM.
By crob09 in forum Mechanical Calculations/Engineering DesignReplies: 0Last Post: 03-01-2014, 09:05 PM -
how to setup the steps per unit in config->motor tuning
By lucky021 in forum Canadian Club HouseReplies: 3Last Post: 05-06-2010, 07:04 PM
Tags for this Thread
Posting Permissions
