[fsa]

dear members
Facing trouble about Diplomatic turret BSV-N-120 locking ..turret going its position but not locking. ..every things good before machine relocate ..please need help

regards

asif

[mbservice]

Is the turret indexing in the correct direction e.g. going 1,2,3,4?

[fsa]

yes brother ...turret operate with jog mode also with mdi thru tool change command..please check the operation sequence on attach jpeg till highlighted the area turret work well after that stuck not complete the cycle my understanding that the at this point turret motor need to be start reverse direction to lock the dist but not happening..

[mbservice]

Yes you've said that it works in jog and mdi I asked does the turret go in the correct direction ?
You said it was working one place and moved so have you checked phasing

[fsa]

yes turret goes in correct direction ..i already change phase to check direction...

[mbservice]

Check diagnostics that locking sensor has released , then check relays that it's telling unit to activate locking pin . Check diagnostics that encoder is changing
What machine is unit on

[fsa]

i am confused sir ..

ok first i check 24v at turret.(please point me in attach pic where i check 24v )



then replace relay with new one

[Jono1961]

Check turret motor proximity sensor gap/clearance is correct,then reset turret timing as mbservice advised earlier.this sensor could be faulty/breaking down.

[fsa]

Jono1961 thanks for join our conversation... r u talking about 6# sensor please check jpeg...highlighted with black circle?? i already maintain the gap between sensor and metal ring as per manual instruction..its 0.8mm to 1mm gap..

2nd thing i dont know how to reset the turret timing can you guide me please

regards

Fsa

[fsa]

dear are you talking about this sensor can be faulty please check attach jpeg highlighted wit yellow lines..

regards

asif

[Jono1961]

See attached photos
I - Locking control switch
6 - also Locking Control Switch

Sorry not certain how to upload better quality pictures

https://www.scribd.com/doc/22636513/DUPLOMATIC-TURRET-1

[fsa]

no photo only manual of turret ...so what i do now????

[Jono1961]

The pictures and information are in the turret manual too if you look.

[fsa]

ok jono 1961 so your advise that i change locking control switch and reset the turret timing..but how to reset the turret timing can you guide me please.

[fsa]

ok jono 1961 so your advise that i change locking control switch and reset the turret timing..but how to reset the turret timing can you guide me please.

Both proximity sensors works ok but indexing Solenoid not de energizing..after energized...I check voltage on indexing Solenoid after tool change cycle activate... voltage is changing from 0 to 17 but not zero till I press the reset button...
I hope this can help you to reach the fault

[fsa]

The pictures and information are in the turret manual too if you look.

Both proximity sensors works ok but indexing Solenoid not de energizing..after energized...I check voltage on indexing Solenoid after tool change cycle activate... voltage is changing from 0 to 17 but not zero till I press the reset button...
I hope this can help you to reach the fault

[fsa]

The pictures and information are in the turret manual too if you look.

Both proximity sensors works ok but indexing Solenoid not de energizing..after energized...I check voltage on indexing Solenoid after tool change cycle activate... voltage is changing from 0 to 17 but not zero till I press the reset button...
I hope this can help you to reach the fault

[RDTS]

Were can I get boring bar holders for the Diplomatic turret BSV-N-120

[mbservice]

Ebay

Were can I get boring bar holders for the Diplomatic turret BSV-N-120

[RDTS]

Ebay

I wish. No joy there. I contacted toolholdershop out of Canada and may have them make me a few.