Hi everyone!

I have Cincinnati Acramatic 2100E Arrow 2 and after changing the battery of the RT board 2379A02
This error come up Alarm 40-33 Output/Fuse Failure in APC Rack 0

RT-Board : PN : 3-424-2379A02
BIOS : Award v 4.51pg (ROM PCI/ISA BIOS (2A5LED42))

We have checked the 24V and fuses but everything is correct



We made the following configuration in the BIOS :

ONLY FOR 2379A02

BE AWARE (SPECIAL CARD): Before you put an AT powersupply to THIS RT Card you must change some Pin options on the card.
Not respecting this procedure will probably destroy the card.

This is the procedure:
- Take a picture of the RT card before doing anything on it, to have a backup PIN configuration.
- Remove the JPP pin
- Put a PIN between 2 and 3 on JP2
- put the P8 and P9 powersupply cord on the RT CARD, the black cables must be in the middle
- Put the VGA Card
- Power on the power supply
At this stage you must see the starting boot, just press the correct button to access to the bios settings.

- Standard CMOS setup:
* the primary master/slave and secondary master/slave must be = NONE
* The drive A and B must be NONE
* Hald on= All but Keyboard

- Bios features setup:
* virus warning disabled
* cpu internal cache enabled
* external cahe enabled
* quick power on self test! enabled
* boot sequence A C SCSI
* swap floppy drive disabled
* boot up floppy seek disabled
* boot up numlock status on
* memory ecc function disabled
* type matic rate settings disabled
* typematic rate chars sec 6
* type matic delay 250
* security option setup
* pci/vga palette snoop disabled
* os select for dram non OS2
* hdd smart capability disabled
* video bios shadow disabled
* C***** disabled (2 lines)
* D***** disabled (4lines)


- Chipset features setup
* dimm 1... Normal
* dimm 2... normal
* sdram ... 3
* video bios cacheable enabled
* system bios cacheable disabled
* memory hole... disabled
* cpu to pci... enabled
* pci dynamic... enabled
* pci master.... enabled
* pci delay... enabled
* pci master .... enabled

- Power management setup
* power management disabled
* pm control.... yes
* video off methos DPMS
* video off... suspend
* stand by mode disabled
* suspend mode disabled
* hdd power on disabled
* resume ... disabled
* from IRQ3 to IRQ7 = Primary
* IRQ8 disabled
* from IRQ9 to IRQ 12 secondary
* IRQ13 primary
* IRQ14 primary
* IRQ15 disabled

- PNP/PCI configuration
* Resources control... Manual
* Reset ... diabled
* IRQ3 and IRQ4 = PCI/ISA PNP
* From IRQ5 to 10= Legacy ISA
* IRQ11 PCI/ISA PNP
* From IRQ12 to IRQ15 LEGACY ISA
* DMA0,1 and 3= PCI/ISA PNP
* DMA5 and DMA6 Legacy...
* DMA7 PCI/ISA PNP
* Pci Irq... Level
* assisgn... disabled
* PCI SLOT1 and 2 = Auto

Integrated Peripherals
* Onboard primary... disabled
* Onboard Secondary diabled
* IDE pref... enabled
* IDE HDD... enabled
* Onboard FCC.. disabled
* Onboard UART 1 = 3E8/IRQ4
* Onboard UART 2 = 2E8/IRQ3
* Onboard Uart2 mode: standard
* onboard parall... disabled

There is a similar thread but without solution
https://www.cnczone.com/forums/cinci...oard-bios.html

Is it possible to have the binary file to flash it?

Many Thanks!