[T2creative]

Hello members, I have this Semipower DriveBlok ADM1003DCH00002 VFD and need with wiring to this Mach3 controller (see attached photos)
Searching online for diagram with no sesult. Anyone have a wiring diagram or experience with this vfd please help. Thank you

[RaderSidetrack]

The name on the manufacturer's label is different, but the manual at this link looks like it may apply to your product:

https://www.artisantg.com/info/Parke...lok_Manual.pdf

[T2creative]

The name on the manufacturer's label is different, but the manual at this link looks like it may apply to your product:

https://www.artisantg.com/info/Parke...lok_Manual.pdf

Thanks for the quick response. I went through the pdf manual, but cannot figure it out. Any one here have experience in wiring vfd please help. Thanks in advance.

[T2creative]

Any cnc experts here that can help me with wiring vfd to a controller.
See attached diagram. Thanks

[mactec54]

Any cnc experts here that can help me with wiring vfd to a controller.
See attached diagram. Thanks

FOR=DN1
COM=DigCom

PWM=3VIN
ACM=ANG
you will have to check the output between PWN /ACM to see if it is a 0-10v dc Analog output the drive requires a +/- 10v so not sure if this is going to work, for this VFD Drive.

Why a VFD Drive like this??

You changed the Breakout Board what was the reason??

[T2creative]

FOR=DN1
COM=DigCom

PWM=3VIN
ACM=ANG
you will have to check the output between PWN /ACM to see if it is a 0-10v dc Analog output the drive requires a +/- 10v so not sure if this is going to work, for this VFD Drive.

Why a VFD Drive like this??

You changed the Breakout Board what was the reason??

Thanks matec54,
I have an old AXYZ Millenium that uses this VFD drive with ELTe spindle.
I am upgrading to a more modern controller, the original controller is old, it requires a very slow USB-RS485 plug to transfer files running on Toolpath software under windows 32bit XP.

[CNCMAN172]

In most cases with CNc controllers the usb-rs485 is the interface used to control the spindle using modbus control

[T2creative]

FOR=DN1
COM=DigCom

PWM=3VIN
ACM=ANG
you will have to check the output between PWN /ACM to see if it is a 0-10v dc Analog output the drive requires a +/- 10v so not sure if this is going to work, for this VFD Drive.

Why a VFD Drive like this??

You changed the Breakout Board what was the reason??

I measured the PIN 3VIN and it is 10v. Will direct connection like this work?

[mactec54]

I measured the PIN 3VIN and it is 10v. Will direct connection like this work?

You need to measure at the control Board not the VFD Drive, this needs to be a variable 0-10v using MDI do S12000 M3 and check the voltage at the Control Board output. what is the max RPM of your spindle.

If the Drive is 10v then that would be a 10v voltage output so that would not be the right connection.

[T2creative]

You need to measure at the control Board not the VFD Drive, this needs to be a variable 0-10v using MDI do S12000 M3 and check the voltage at the Control Board output. what is the max RPM of your spindle.

If the Drive is 10v then that would be a 10v voltage output so that would not be the right connection.

Here is the original wiring going to the break out board. Using pins 8 to 11

[mactec54]

Here is the original wiring going to the break out board. Using pins 8 to 11

Pin 8 / 9 is for 0n / 0ff control only.