Looking for FANUC 0-T Operator Manual
Thank you
Looking for FANUC 0-T Operator Manual
Thank you
PM sent
Al.
CNC, Mechatronics Integration and Custom Machine Design
“Logic will get you from A to B. Imagination will take you everywhere.”
Albert E.
Al the man i also am looking for a faunuc manual could you possibly let me know were i may get such as well
laserman send me a PM with your email and which one you need.
Stevo
Looking for FANUC 0-T Operator Manual too.
Thanks
Send me a PM with your email
Stevo
I guess your need are taken care of...
Al.
CNC, Mechatronics Integration and Custom Machine Design
“Logic will get you from A to B. Imagination will take you everywhere.”
Albert E.
hi Stevo
I am looking for FANUC OTT book, do you have this? This control is on 1992 PUMA 10S double turret.
thanking you
Stan
Sir FANUC TT means Double Turret please send a mail with your E mail so i can send it to you regards, [email protected]
Stan,
Which book are you looking for? Programming, parameter, maint?
Let me know if your prabhat can't get you all of what you need.
Stevo
hi Stevo1
thank you, at this moment, I have nothing from yours prabhat. I need programming book, please. I need also help: I bought this machine used and am just starting to set it up and I made some mismatch by running and old program inside and I have failure: "not ready" and program running . I cannot reset system!! what can I do?
thanking you, have a nice day
Stan
I also could use the Fanuc O-TT manual. I have a Star CNC 32 that has some alarms I can't figure out.
Thanks,
Heath
Dear Friends,
i can not Upload the Manual here If you are in Need send a mail with your E mail address.
Do not ask Like I did not get anything.You are looking NOT ready While Program is running It may be due to The force Bye pass of interlock, Please say the details about the machine So we can help you.
warm Regadrs
Prabhat Mishra
yours_prabhat, I have sent you an e-mail.
My machine is a Star KNC 32 running a Fanuc O-TT.
Alarm messages are:
Head 1: O4044 N0002
No. 2000
Emergency Stop
Head 2: O1820 N1820
No. 2000
Emergency Stop
Sir,
the Alarm 2000 Emergency Stop is an external Alarm not a system Alarm , Please check through the ladder The Emergency circuit, Like = Hyd or Pneumatic pressure Sw, Turret Clamp, Gear Pos sw, Etc Etc.
Hope you will do it If Problem persisits, Please communicate me on [email protected]
Regards
Prabhat Mishra
Dear All,
Here are some basic ALARM DETAILS for FANUC
Alarms Fanuc Alpha Servo Drive
1 :Over-voltage alarm (HV)
2 :Low control power voltage alarm (LV)
3 :Low DC link voltage alarm (LVDC)
4 :Regenerative dis-charge control circuit failure alarm (DCSW)
5 :Over-regenerative discharge alarm (DCOH)
6 :L-and M-axis over-current alarm (HCM)
6. :L-and M-axis IPM alarm (IPMLM)
7 ynamic brake circuit failure alarm (DBRLY)
8 :L-axis over-current alarm (HCL)
8. :L-axis IPM alarm (IPML)
9 :M-axis over-current alarm (HCM)
9. :M-axis IPM alarm (IPML)
AlarmsFanuc Alpha Spindle Drive
AL-01 : MOTOR OVERHEAT
AL-02 : EX SPEED ERROR
AL-03 : FUSE ON DC LINK BLOWN
AL-04 : INPUT FUSE/POWER FAULT
AL-05 : POWER SUPPLY FUSE BLOWN
AL-07 : OVERSPEED
AL-08 : HIGH VOLT IN-PUT POWER
AL-09 : OVERHEAT MAIN CIRCUIT
AL-10 : LOW VOLT IN-PUT POWER
AL-11 : OVERVOLT POW CIRCUIT
AL-12 : OVERCUR-RENT POW CIRCUIT
AL-13 : DATA MEMORY FAULT CPU
AL-15 : SP SWITCH CONTROL ALARM
AL-16 : RAM FAULT
AL-18 : SUMCHECK ERROR PGM DATA
AL-19 : EX OFFSET CURRENT U
AL-20 : EX OFFSET CURRENT V
AL-24 : SERIAL TRANSFER ERROR
AL-25 : SERIAL TRANSFER STOP
AL-26 : DISCONNECT C VELO DETECT
AL-27 : DISCONNECT POS-CODER
AL-28 : DISCONNECT C-POS DE-TECT
AL-29 : SHORTTIME OVERLOAD
AL-30 : OVERCURRENT POW CIRCUIT
AL-31 : MOTOR LOCK OR V-SIG LOS
AL-32 : RAM FAULT SERIAL LSI
AL-33 : SHORTAGE POWER CHARGE
AL-34 : PARAMETER SETTING ERROR
AL-35 : EX SETTING GEAR RATIO
AL-36 : OVERFLOW ERROR COUNTER
AL-37 : SPEED DETECT PAR. ERROR
AL-39 : 1-ROT Cs SIGNAL ERROR
AL-40 : NO 1 ROT Cs SIGNAL DETECT
AL-41 : 1-ROT POSCODER ERROR
AL-42 : NO 1-ROT. POSCODER DETECT
AL-43 : DISCON. PC FOR DIF. SP. MOD.
AL-44 : CONTROL CIRCUIT(AD) ERROR
AL-46 : SCREW 1-ROT POSCOD. ALARM
AL-47 : POS-CODER SIGNAL AB-NORMAL
AL-49 : HIGH CONV. DIF. SPEED
AL-50 : SPNDL CON-TROL OVER-SPEED
AL-51 : LOW VOLT DC LINK
AL-52 : ITP SIGNAL ABNORMAL I
AL-53 : ITP SIGNAL ABNORMAL II
AL-56 : INNER COOLING FAN STOP
AL-57 : EX DECEL-ERATION POWER
AL-58 : OVERLOAD IN PSM
AL-59 : COOLING FAN STOP IN PSM
Fanuc Alpha Power Supply Fault Code
AL-01 The main circuit power module (IPM) has detected am Error (PSM-5.5,-11) Overcurrent flows into the input of the main circuit (PSM-15 to –30)
AL-02 A cooling fan for the control circuit has stopped
AL-03 The Temperature of the main circuit heat sink has risen abnormally
AL-04 In the main circuit the DC voltage (DC Link) has dropped
AL-05 The main circuit capacitor was not recharged within the specified time
AL-06 The Input Power Supply is abnormal (open phase)
AL-07 In the main circuit the DC Voltage at the DC link is abnormally high
[email protected]
Regards
Prabhat Mishra