[SCHMIDT]

Hi everyboby. I'm new here and really hope you can help me...

when running following program the machine seems to disregard all the roundings and just run in straight lines from start to end dia.
but in G70 and simulation on the pc it works right??

N4 G97 X6.0 Z3. M8
G71P305Q700U-0.2W0.1D600F0.1
N305 G00 X39.698 Z3.010
N307 G01 G41
N310 G01 X34.698 Z0.010 F0.05
N315 G01 X29.698 Z0.010
N320 G02 X28.024 Z-0.065 I0.074 K-5.549
N325 X27.769 Z-0.088 I0.710 K-4.268
N330 X27.383 Z-0.143 I0.229 K-1.161
N335 X26.920 Z-0.259 I0.467 K-1.223
N340 X26.791 Z-0.301 I1.847 K-2.927
N345 X26.527 Z-0.404 I0.591 K-0.892
N350 X26.463 Z-0.434 I1.852 K-2.020
N355 X26.430 Z-0.450 I2.052 K-2.170
N360 X26.155 Z-0.604 I0.932 K-0.970
N365 X25.979 Z-0.738 I0.890 K-0.679
N370 X25.947 Z-0.767 I2.387 K-1.330
N375 X25.873 Z-0.842 I1.045 K-0.566
N380 X25.821 Z-0.906 I0.744 K-0.338
N385 X25.606 Z-1.280 I2.977 K-1.056
N390 X25.528 Z-1.466 I9.833 K-2.175
N395 X25.502 Z-1.540 I1.291 K-0.260
N400 X25.253 Z-2.428 I215.343 K-30.637
N405 X25.168 Z-2.738 I235.426 K-32.505
N410 X24.973 Z-3.479 I78.076 K-10.675
N415 X24.967 Z-3.501 I166.488 K-21.157
N420 X24.718 Z-4.535 I81.524 K-10.349
N425 X24.709 Z-4.573 I5.826 K-0.665
N430 G01 X24.489 Z-5.601
N435 X24.280 Z-6.576
N440 G03 X24.258 Z-6.679 I-36.183 K3.858
N445 X24.094 Z-7.421 I-453.416 K49.650
N450 X24.014 Z-7.769 I-41.791 K4.645
N455 X23.879 Z-8.321 I-146.361 K17.502
N460 X23.733 Z-8.872 I-29.206 K3.605
N465 X23.628 Z-9.234 I-75.017 K10.699
N470 X23.375 Z-10.003 I-23.752 K3.505
N475 X23.334 Z-10.116 I-47.586 K8.609
N480 X22.946 Z-11.055 I-21.118 K3.872
N485 X22.884 Z-11.190 I-42.771 K9.834
N490 X22.405 Z-12.112 I-18.501 K4.315
N495 X21.727 Z-13.178 I-18.818 K5.394
N500 X21.718 Z-13.191 I-37.472 K13.100
N505 X20.917 Z-14.238 I-18.512 K6.479
N510 X20.220 Z-15.027 I-17.705 K7.357
N515 X19.967 Z-15.294 I-48.587 K22.804
N520 X19.169 Z-16.093 I-21.871 K10.412
N525 X19.015 Z-16.240 I-51.653 K26.970
N530 X18.199 Z-16.989 I-25.388 K13.349
N535 X17.985 Z-17.178 I-64.296 K36.285
N540 X17.536 Z-17.571 I-65.764 K37.369
N545 X16.875 Z-18.123 I-16.809 K9.685
N550 X16.456 Z-18.450 I-11.913 K7.401
N555 X15.652 Z-19.055 I-108.338 K71.530
N560 X15.170 Z-19.410 I-25.451 K17.009
N565 G02 X14.423 Z-19.957 I62.022 K-42.720
N570 X13.655 Z-20.527 I260.020 K-175.746
N575 X13.243 Z-20.837 I28.582 K-19.227
N580 X12.745 Z-21.218 I89.015 K-58.495
N585 X12.136 Z-21.697 I21.028 K-13.690
N590 X11.960 Z-21.840 I48.408 K-29.977
N595 X11.127 Z-22.544 I19.798 K-12.180
N600 X10.361 Z-23.248 I19.612 K-11.133
N605 X10.219 Z-23.385 I48.427 K-25.261
N610 X9.785 Z-23.808 I46.845 K-24.268
N615 X9.399 Z-24.211 I8.951 K-4.535
N620 X9.075 Z-24.591 I8.856 K-4.002
N625 X8.655 Z-25.119 I60.001 K-24.102
N630 X8.326 Z-25.545 I60.557 K-23.709
N635 X7.964 Z-26.044 I13.642 K-5.231
N640 X7.942 Z-26.076 I31.626 K-10.826
N645 X7.404 Z-26.944 I15.244 K-5.201
N650 X7.122 Z-27.467 I27.862 K-7.782
N655 X6.995 Z-27.767 I3.263 K-0.846
N660 X6.950 Z-27.953 I2.163 K-0.355
N665 X6.871 Z-28.527 I38.212 K-2.947
N670 X6.847 Z-28.757 I11.047 K-0.686
N675 X6.784 Z-29.554 I230.581 K-9.489
N680 X6.729 Z-30.314 I234.359 K-8.833
N685 X6.715 Z-30.598 I16.159 K-0.557
N690 X6.706 Z-31.121 I31.920 K-0.538
N695 G01 X6.6 Z-32.
N700 X6.
G00 G40 X6. Z3. I0 K0
G00 X6. Z3.
Z150.

[zicci]

Try using R instead of I and K
Use pythagoras to convert to R
SQRT(I^+K^)

[rapidtraverse]

Have you ran the g-70?

G-71 may not cut your arc's as it is primarillary a roughing routine and often will not cut arc's.

[CNCRim]

The max execution for G70 is 50lines, ur rough cycle is too long. Try R instead I and K some machine don't support it.

Hi everyboby. I'm new here and really hope you can help me...

when running following program the machine seems to disregard all the roundings and just run in straight lines from start to end dia.
but in G70 and simulation on the pc it works right??

N4 G97 X6.0 Z3. M8
G71P305Q700U-0.2W0.1D600F0.1
N305 G00 X39.698 Z3.010
N307 G01 G41
N310 G01 X34.698 Z0.010 F0.05
N315 G01 X29.698 Z0.010
N320 G02 X28.024 Z-0.065 I0.074 K-5.549
N325 X27.769 Z-0.088 I0.710 K-4.268
N330 X27.383 Z-0.143 I0.229 K-1.161
N335 X26.920 Z-0.259 I0.467 K-1.223
N340 X26.791 Z-0.301 I1.847 K-2.927
N345 X26.527 Z-0.404 I0.591 K-0.892
N350 X26.463 Z-0.434 I1.852 K-2.020
N355 X26.430 Z-0.450 I2.052 K-2.170
N360 X26.155 Z-0.604 I0.932 K-0.970
N365 X25.979 Z-0.738 I0.890 K-0.679
N370 X25.947 Z-0.767 I2.387 K-1.330
N375 X25.873 Z-0.842 I1.045 K-0.566
N380 X25.821 Z-0.906 I0.744 K-0.338
N385 X25.606 Z-1.280 I2.977 K-1.056
N390 X25.528 Z-1.466 I9.833 K-2.175
N395 X25.502 Z-1.540 I1.291 K-0.260
N400 X25.253 Z-2.428 I215.343 K-30.637
N405 X25.168 Z-2.738 I235.426 K-32.505
N410 X24.973 Z-3.479 I78.076 K-10.675
N415 X24.967 Z-3.501 I166.488 K-21.157
N420 X24.718 Z-4.535 I81.524 K-10.349
N425 X24.709 Z-4.573 I5.826 K-0.665
N430 G01 X24.489 Z-5.601
N435 X24.280 Z-6.576
N440 G03 X24.258 Z-6.679 I-36.183 K3.858
N445 X24.094 Z-7.421 I-453.416 K49.650
N450 X24.014 Z-7.769 I-41.791 K4.645
N455 X23.879 Z-8.321 I-146.361 K17.502
N460 X23.733 Z-8.872 I-29.206 K3.605
N465 X23.628 Z-9.234 I-75.017 K10.699
N470 X23.375 Z-10.003 I-23.752 K3.505
N475 X23.334 Z-10.116 I-47.586 K8.609
N480 X22.946 Z-11.055 I-21.118 K3.872
N485 X22.884 Z-11.190 I-42.771 K9.834
N490 X22.405 Z-12.112 I-18.501 K4.315
N495 X21.727 Z-13.178 I-18.818 K5.394
N500 X21.718 Z-13.191 I-37.472 K13.100
N505 X20.917 Z-14.238 I-18.512 K6.479
N510 X20.220 Z-15.027 I-17.705 K7.357
N515 X19.967 Z-15.294 I-48.587 K22.804
N520 X19.169 Z-16.093 I-21.871 K10.412
N525 X19.015 Z-16.240 I-51.653 K26.970
N530 X18.199 Z-16.989 I-25.388 K13.349
N535 X17.985 Z-17.178 I-64.296 K36.285
N540 X17.536 Z-17.571 I-65.764 K37.369
N545 X16.875 Z-18.123 I-16.809 K9.685
N550 X16.456 Z-18.450 I-11.913 K7.401
N555 X15.652 Z-19.055 I-108.338 K71.530
N560 X15.170 Z-19.410 I-25.451 K17.009
N565 G02 X14.423 Z-19.957 I62.022 K-42.720
N570 X13.655 Z-20.527 I260.020 K-175.746
N575 X13.243 Z-20.837 I28.582 K-19.227
N580 X12.745 Z-21.218 I89.015 K-58.495
N585 X12.136 Z-21.697 I21.028 K-13.690
N590 X11.960 Z-21.840 I48.408 K-29.977
N595 X11.127 Z-22.544 I19.798 K-12.180
N600 X10.361 Z-23.248 I19.612 K-11.133
N605 X10.219 Z-23.385 I48.427 K-25.261
N610 X9.785 Z-23.808 I46.845 K-24.268
N615 X9.399 Z-24.211 I8.951 K-4.535
N620 X9.075 Z-24.591 I8.856 K-4.002
N625 X8.655 Z-25.119 I60.001 K-24.102
N630 X8.326 Z-25.545 I60.557 K-23.709
N635 X7.964 Z-26.044 I13.642 K-5.231
N640 X7.942 Z-26.076 I31.626 K-10.826
N645 X7.404 Z-26.944 I15.244 K-5.201
N650 X7.122 Z-27.467 I27.862 K-7.782
N655 X6.995 Z-27.767 I3.263 K-0.846
N660 X6.950 Z-27.953 I2.163 K-0.355
N665 X6.871 Z-28.527 I38.212 K-2.947
N670 X6.847 Z-28.757 I11.047 K-0.686
N675 X6.784 Z-29.554 I230.581 K-9.489
N680 X6.729 Z-30.314 I234.359 K-8.833
N685 X6.715 Z-30.598 I16.159 K-0.557
N690 X6.706 Z-31.121 I31.920 K-0.538
N695 G01 X6.6 Z-32.
N700 X6.
G00 G40 X6. Z3. I0 K0
G00 X6. Z3.
Z150.

[eject_21]

Really? 50 lines max??? I've never had more than 10 or 12, but that's a pretty useful piece of information to me. Thanks 2006.

[Sakis818]

G71 Syntax is

N1 G71 U( ) R( )
N2 G71 P100 Q300 U0.5 W0.025 F0.2
N100-N300 GEOMETRY. WHAT I'M SAYING IS THAT YOU SHOULD SET DEPTH OF CUT(U)
AND REMOVE DISTANCE OF THE TOOL ON PASSES (R).

[zicci]

Yes you should indicate depth of cut in G71 Cycle
If you use OT Control then doc is U2.( per side ) R.5 ( must be less than
value in U ) This is only the cut retract value.
If you use 6T Control then everything including doc is specified in
G71 line ie D2000 ( without decimal point ),in 6T Control retract value
is set with parameter
Hope this helps
Zicci