586,060 active members*
4,191 visitors online*
Register for free
Login

Thread: TNC 145 cs Lights On

Results 1 to 7 of 7
  1. 12-27-2008, 06:22 AM #1
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37

    TNC 145 cs Lights On

    Tonight upon normal startup all the LEDs stayed lit and the monitor is blank
    Normally I press the CE button and continue.
    What is wrong with my controller ?

    Thanks to all of you
    Mark
    Attached Thumbnails Attached Thumbnails controlle.jpg  
    Reply With Quote Reply With Quote
  2. 12-27-2008, 06:34 PM #2
    machintek
    machintek is offline Moderator
    Join Date
    Nov 2004
    Posts
    3028
    Stuck in boot?
    Processor haulted?
    Logic power supply issue?
    Call Heidenhain.

    George
    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
    Reply With Quote Reply With Quote
  3. 12-27-2008, 07:02 PM #3
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37
    I have no idea, this just happened last night. I will call H monday morning.
    I have all the TNC manuals but there isn't any troubleshooting guide
    Reply With Quote Reply With Quote
  4. 12-27-2008, 07:03 PM #4
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37
    what I will say is i am panicking just a bit
    Reply With Quote Reply With Quote
  5. 12-31-2008, 03:11 AM #5
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37
    the unit has been removed from the machine and shipped off to Morlin Inc in Erie Pa.
    I will post the results
    Wish me luck
    Reply With Quote Reply With Quote
  6. 01-13-2009, 03:55 AM #6
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37
    tnc is supposedly repaired and on its way back to me.'
    Very good turnaround,Super nice guy Dave, plus he loaded my parameters back in the unit.
    Found some bad chips in the boards
    Mark
    Reply With Quote Reply With Quote
  7. 01-19-2009, 03:25 AM #7
    mjp
    mjp is offline Registered
    Join Date
    Oct 2004
    Posts
    37
    The TNC 145 is back home in its cabinet and working fine.
    Service was great,Price was very reasonable.Turnaround was also very good
    Mark
    www.mjpcarbon.com
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Running Lights out
    By gizmo_454 in forum Haas Mills
    Replies: 18
    Last Post: 08-04-2012, 10:59 PM
  2. SL-10 lights-out running?
    By shawncnelson in forum Haas Lathes
    Replies: 15
    Last Post: 04-21-2009, 03:44 AM
  3. Work Lights
    By GEM in forum Haas Mills
    Replies: 0
    Last Post: 08-22-2007, 10:58 PM
  4. Lights out CNC turning
    By Flycut in forum News Announcements
    Replies: 0
    Last Post: 01-17-2007, 06:40 PM
  5. Best Christmas Lights EVER seen!
    By DennisCNC in forum Community Club House
    Replies: 27
    Last Post: 12-20-2005, 11:15 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules