[keelhauled]

Try this Wooderson

[wooderson]

thanks keelhauled, It looks excellent after I touched it up, I really appreciate it. I will be sure to post the pictures after I engrave it... thanks again..

[fretsman]

thanks keelhauled, It looks excellent after I touched it up, I really appreciate it. I will be sure to post the pictures after I engrave it... thanks again..

Would you mind explaining by what you mean about "touching it up", for me? I downloaded the sox dxf and noticed the lines were not perfectly straight. It this what you touched up and may I ask how you did that?

I enclosed a screenshot of the dxf opened up and did a regen all command and this is the best I got.

[gravy]

I need some help. My church wants me to do some engravings of their logo. I've engraved this DXF before and it gave them a nice little plaque thang. The things they want me to make now are much smaller and the double lined text on them runs together. I need to make all the text on this logo into a stick type font so they are all single line engraving and still look like the original. I've tried wintopo with a pretty bad result.

Here is a .pdf file and the dxf I have now. I have an .ai file, an .eps file, and a .raw file if that would help.

[Jamf2]

Wooderson

Can you post your cleaned up version. I would like to compare the too and try to explain to fretsman.

Thanks.

[teamtexas]

Here's one for the mix.

[wooderson]

here it is...

[RayinNH]

[QUOTE=gravy;436724]I need some help. My church wants me to do some engravings of their logo. I've engraved this DXF before and it gave them a nice little plaque thang. The things they want me to make now are much smaller and the double lined text on them runs together. I need to make all the text on this logo into a stick type font so they are all single line engraving and still look like the original. I've tried wintopo with a pretty bad result.

hope this will work for you

Ray

[mcnerney]

Gravy

Here is another version of your drawing with the lettering contouring the circle a little better. RayinNH no offense intended.

[RayinNH]

Gravy

Here is another version of your drawing with the lettering contouring the circle a little better. RayinNH no offense intended.

None taken, I just used the font that was there & offset it to the centerline, because Gravy said he wanted the letters to look the same. I figured there would be more than one response to the post.

[keelhauled]

Heres a nice one

[ericandmollie]

This is a WindSpinner. The best way to cut this out would probably be a waterjet or laser CNC cutting 14 gage (.074) Steel, and then apply a nice patina and seal it up. Also need a swival hook to attach thread to hole so it is allowed to spin. I attached a completed picture to show you guys what the finished product should look like. When it is cut, grab the wolf picture and give it a little twist and it should spread out. You can also take the wolf out and insert any other picture in there.

[Weldtutor]

waterjet or laser

Thanks for sharing the file ericandmollie. Keep up the good work. :wave:
The scalloped edges give a nice effect to the finished spinner!

My plasma arc CNC machine was used & did a fine job cutting this from 16 Ga steel.
A photo of the completed item is shown HERE.

Below is the partly finished spinner.

[Switcher]

ericandmollie,

Nice WindSpinner file.


------------------------------------

Weldtutor, Good job cutting that spinner.

Very clean cuts!


.

[ericandmollie]

Good Cut Weldtutor, thanks for the pic!

[ericandmollie]

Here is another style of the spinner

[kram242]

Cool thank you

[ger21]

comic characters are copyrighted and may not be posted here.

[Two9zero4]

I have the rights to the comic....We are trying to make a trophy for a Johnny Hart sponsored golf fund raiser, and I am having a hard time vectoring the image. If someone could help me out I would be very greatful.
THanks,
Brendan

[fretsman]

here it is...

You did a fantastic job cleaning that up, may I ask what you used and how you did that?

Thanks-
Dave