Hi all
My CNC machine used Fanuc OMC, every thing seem OK, but I can't see the program on screen when I use dripfeed mode( the machine can work untill the end of program, but I can't check witch the command 's doing). Please guide me how to fix this problem. Thanks you so much.
Nam
Results 1 to 9 of 9
-
07-25-2013, 12:37 AM #1
Member
- Join Date
- May 2008
- Posts
- 107
Fanuc OMC not display program in dripfeed mode
-
07-25-2013, 09:41 AM #2
Gold Member
- Join Date
- Mar 2003
- Posts
- 2932
From the 0M-C Operator's Manual:
In DNC operation mode, no program can be displayed. Only the
current block and subsequent block can be displayed.
-
07-26-2013, 08:19 PM #3
Registered
- Join Date
- Dec 2009
- Posts
- 972
you will never see the program on 0M
the only way is just check the "distance to go" and know where the machine is moving
-
07-28-2013, 06:21 AM #4
Member
- Join Date
- May 2008
- Posts
- 107
@dcoupar and @ zavateandu: Thanks you so much.
-
07-29-2013, 02:41 PM #5
Registered
- Join Date
- Mar 2005
- Posts
- 816
Is there a parameter for this?
-
07-29-2013, 04:48 PM #6
Registered
- Join Date
- Apr 2009
- Posts
- 1379
In order for a control to display the drip-fed program, it would have to read it in first; that requires sufficient remaining memory. If that memory is available, you may as well load the program and run it from memory. That way is IS displayed.
-
02-05-2014, 07:16 PM #7
Registered
- Join Date
- Feb 2014
- Posts
- 1
Dahlih MCV 1350 (FANUC OM series) parameter files that I need Can you help friends who are over the counter
-
02-08-2014, 09:43 AM #8
Registered
- Join Date
- Dec 2009
- Posts
- 972
are froma 6M sorry
i can not delete pictures
-
10-30-2016, 10:42 PM #9
Registered
- Join Date
- Apr 2016
- Posts
- 5
Re: Fanuc OMC not display program in dripfeed mode
how can you display the current block ?
i want to run in dnc mode a program from memory and i want to see the current line?
Reply With QuoteSimilar Threads
-
Fanuc 6TA,can not see program in MEMORY mode
By jolulank in forum FanucReplies: 5Last Post: 05-29-2013, 07:04 PM -
FANUC 6T CONTROL LOCKS UP WHEN MODE IS SWITCHED TO PROGRAM
By AZTEXAN_MIMXII in forum FanucReplies: 8Last Post: 11-30-2012, 10:15 PM -
Program display prblem in DNC mode（FANUC 0i-MD）
By Samuel2012 in forum FanucReplies: 0Last Post: 09-10-2012, 04:57 AM -
Fanuc O-TT will only run program with rapid in setup mode
By kmcmillen571 in forum FanucReplies: 3Last Post: 07-13-2011, 02:32 PM -
Need Help to Set cnc Dahlih MCV 1350 in Dripfeed mode
By aslam819 in forum CNC (Mill / Lathe) Control Software (NC)Replies: 8Last Post: 02-09-2011, 01:58 AM
Posting Permissions
