603,957 active members*

3,504 visitors online*

Register for free

Login

IndustryArena Forum > MetalWorking Machines > Uncategorised MetalWorking Machines > Vertical Mill, Lathe Project Log > 18x18 Linear Rail Tormach Build.

Thread: 18x18 Linear Rail Tormach Build.

Results 1 to 20 of 1014

Thread Tools
Search Thread
- Advanced Search
Display
- Switch to Linear Mode
- Switch to Hybrid Mode
- Threaded Mode

Threaded View

nateman_doo 18x18 Linear Rail Tormach... 05-23-2012, 07:42 PM

keebler303 Could you shim the i beams at... 05-23-2012, 09:01 PM

SCzEngrgGroup ANY extruded aluminum piece... 05-23-2012, 10:19 PM

packrat Not to mention that they are... 05-23-2012, 11:05 PM

FannBlade I will be watching. I love... 05-23-2012, 11:53 PM

nateman_doo Thanks! I wasn't looking for... 05-24-2012, 12:30 PM

nateman_doo While waiting for the new... 06-01-2012, 07:32 PM

SCzEngrgGroup If it makes you feel any... 06-01-2012, 08:40 PM

nateman_doo heh... thanks. The basement... 06-04-2012, 02:52 PM

nateman_doo new beams arriving friday. ... 06-07-2012, 05:56 PM

MichaelHenry Interesting build approach. ... 06-07-2012, 08:01 PM

nateman_doo Because I am using a Tormach... 06-10-2012, 04:23 AM

MichaelHenry There must be an interesting... 06-11-2012, 07:15 PM

rowbare Tormach sells them off the... 06-11-2012, 08:08 PM

nateman_doo Yup. Started with an X2 head... 06-18-2012, 02:47 PM

nateman_doo Someone PLEASE put a foot in... 09-20-2012, 02:39 PM

DRock Just do it! Stop thinking... 09-20-2012, 03:43 PM

nateman_doo I took your advise and... 12-13-2012, 03:29 PM

nateman_doo I just want it perfect. I... 09-20-2012, 04:15 PM

nateman_doo Forgot to post a picture of... 09-20-2012, 04:24 PM

nateman_doo Finally started back up on... 12-13-2012, 03:17 PM

nateman_doo Made leaps and bounds of... 12-16-2012, 09:03 AM

outsider787 Great work man! That's... 12-16-2012, 08:52 PM

cjsamples Tormach head 12-16-2012, 10:55 PM

nateman_doo Next time I walk in the... 12-17-2012, 03:31 AM

nateman_doo Yea, the top plate is 1.5"... 12-17-2012, 03:28 AM

nateman_doo Here are the Aluminum slabs... 12-17-2012, 02:59 PM

nateman_doo Finally finished my Y axis! ... 12-21-2012, 07:46 AM

poordumbasstard it looks like a tank 12-21-2012, 08:17 AM

vcatalasan Wow this is very nice, its... 12-21-2012, 10:00 AM

nateman_doo Thanks! 3 reasons, first... 12-21-2012, 03:19 PM

nateman_doo Its final resting place is 5... 12-21-2012, 02:51 PM

BAMCNC.COM Pretty sweet job there, to... 12-21-2012, 02:59 PM

FannBlade My mouth is watering for this... 12-21-2012, 03:23 PM

FannBlade My mouth is watering for this... 12-21-2012, 03:24 PM

nateman_doo Thanks! You and me both. I... 12-21-2012, 03:53 PM

FannBlade That would suck to have a... 12-21-2012, 04:09 PM

nateman_doo Hurricane Sandy gave us on... 12-21-2012, 05:00 PM

vcatalasan Nateman, so what is the... 12-21-2012, 06:16 PM

nateman_doo 18x18 is the work envelope as... 12-21-2012, 07:30 PM

nateman_doo About to order the 570 oz... 12-22-2012, 04:13 PM

amishx64 I don't know what drivers you... 12-22-2012, 08:10 PM

CROSSHATCH Hey man, great build. ... 12-22-2012, 06:43 PM

SCzEngrgGroup The correct supply voltage... 12-22-2012, 09:23 PM

nateman_doo I never even heard of that. ... 12-22-2012, 09:28 PM

nateman_doo I live in morris county. ... 12-22-2012, 09:25 PM

nateman_doo 2.5mH. I calculate 50V? ... 12-22-2012, 11:04 PM

amishx64 50V looks right to me. 12-23-2012, 02:05 AM

nateman_doo I guess thats why my X2... 12-23-2012, 03:28 AM

nateman_doo I do like the style i linked... 12-23-2012, 06:34 PM

nateman_doo 56V 11A 5V 12V Robotic Motion... 12-25-2012, 05:11 AM

nateman_doo 56V 11A 5V 12V Robotic Motion... 12-25-2012, 05:32 AM

nateman_doo Merry Christmas everyone!! 12-25-2012, 05:31 PM

nateman_doo Took the day off, so I will... 12-26-2012, 06:12 PM

nateman_doo I beams bolted. daily... 12-27-2012, 01:51 AM

nateman_doo On a side note... Having... 12-27-2012, 02:53 AM

cjsamples coupling loose 12-27-2012, 03:06 AM

nateman_doo nope, I can see the coupler... 12-27-2012, 12:14 PM

amishx64 Try turning the acceleration... 12-27-2012, 11:15 PM

nateman_doo I will try anything at this... 12-28-2012, 01:46 AM

amishx64 You tried it with lower... 12-28-2012, 02:39 AM

nateman_doo I lowered the accel, but it... 12-28-2012, 05:45 AM

Hans_G keep at it- you're making... 12-28-2012, 04:07 PM

Fastest1 Just read it all. Nice work.... 12-28-2012, 06:12 PM

cjsamples wiring 12-28-2012, 06:22 PM

nateman_doo Zero backlash! Sorry its a... 12-28-2012, 09:22 PM

nateman_doo And first movements with a... 12-28-2012, 09:24 PM

vcatalasan Hi Nate, What ballscrews... 12-28-2012, 10:29 PM

nateman_doo I think they are somewhere in... 12-29-2012, 03:07 AM

nateman_doo I was tired of messing around... 12-29-2012, 08:46 AM

nateman_doo BTW, the X2 wires were kind... 12-29-2012, 08:49 AM

cjsamples Too much Voltage 12-29-2012, 04:05 PM

Fireman11 How did you get the rails... 12-29-2012, 07:38 PM

nateman_doo I am using this motor:... 12-29-2012, 07:42 PM

nateman_doo Funny you mentioned it I... 12-29-2012, 10:40 PM

nateman_doo Made a completely new... 12-29-2012, 11:51 PM

cjsamples Stepper Driver 12-30-2012, 12:36 AM

nateman_doo Yea, Should be 50. At least... 12-30-2012, 01:44 AM

cjsamples 70 Volts...... 12-30-2012, 02:20 AM

nateman_doo whats the difference between... 12-30-2012, 02:26 AM

cjsamples Can-o-worms 12-30-2012, 02:36 AM

cjsamples The linear rail build 12-30-2012, 02:41 AM

nateman_doo I cant speak highly enough... 12-30-2012, 04:47 AM

nateman_doo Z axis coming along well:... 12-30-2012, 05:06 AM

amishx64 Nice work so far! Can you... 12-30-2012, 05:48 AM

nateman_doo You mean the back plate of... 12-30-2012, 06:02 AM

nateman_doo 31758 - Complete PCNC 770... 12-30-2012, 06:16 AM

nateman_doo FOUND IT HERE... 12-30-2012, 06:42 AM

amishx64 Amazing. Thank you! This... 12-31-2012, 02:40 AM

nateman_doo Yes it is. It is quite an... 12-31-2012, 03:30 AM

nateman_doo Just found some nice wire for... 12-31-2012, 06:27 PM

cjsamples wire 12-31-2012, 06:35 PM

nateman_doo yup! has the 4 wires for the... 12-31-2012, 07:15 PM

nateman_doo Happy New Year! Back to... 01-02-2013, 01:13 AM

keebler303 A note on wire: Igus... 01-02-2013, 03:45 AM

nateman_doo I already ordered the wire so... 01-02-2013, 05:55 AM

keebler303 Mcmaster has excellent... 01-02-2013, 03:28 PM

nateman_doo For some stupid reason I... 01-02-2013, 06:27 AM

nateman_doo I just ordered some of the... 01-03-2013, 01:59 AM

nateman_doo http://www.igus.com/us/pdf/s08... 01-03-2013, 02:22 AM

nateman_doo After a dinner like a boss...... 01-03-2013, 05:51 AM

amishx64 As always, your work looks... 01-03-2013, 06:41 AM

nateman_doo Thanks! My goal is to have... 01-03-2013, 02:31 PM

nateman_doo WOW?! ... 01-03-2013, 05:05 PM

CROSSHATCH Have you never used... 01-03-2013, 06:27 PM

keebler303 I told you they were legit! 01-03-2013, 05:26 PM

keebler303 Nope, he got it direct from... 01-03-2013, 06:46 PM

CROSSHATCH Rookie mistake on my part for... 01-04-2013, 01:40 PM

nateman_doo Yup, got it directly from... 01-03-2013, 08:44 PM

nateman_doo Z axis almost done:... 01-03-2013, 08:48 PM

nateman_doo I finished every thing I set... 01-04-2013, 04:23 AM

nateman_doo Side note... Does anyone... 01-04-2013, 05:00 AM

vcatalasan Mcmaster? you might need to... 01-04-2013, 06:32 AM

cjsamples little bit 01-04-2013, 08:22 AM

vcatalasan I have similar units, anyone... 01-04-2013, 08:37 AM

nateman_doo nooo way. Chinese prices :) ... 01-04-2013, 04:34 PM

scleaf I noticed that the base of... 01-04-2013, 09:49 AM

nateman_doo There is no way I would be... 01-04-2013, 06:39 PM

scleaf Then I would say you have a... 01-05-2013, 01:03 AM

keebler303 I have gotten custom bored... 01-04-2013, 04:38 PM

LeeWay The only helical I have is a... 01-04-2013, 05:23 PM

nateman_doo I have oldhams on my X2 and... 01-04-2013, 06:42 PM

LeeWay I have heard of a lot of... 01-04-2013, 07:06 PM

nateman_doo My oldham discs are probably... 01-04-2013, 08:22 PM

vcatalasan Wow that is a back breaker... 01-04-2013, 09:33 PM

nateman_doo I have moved it in and out of... 01-05-2013, 12:43 AM

nateman_doo I was guess the entire weight... 01-05-2013, 03:23 AM

SCzEngrgGroup Running home/limit wiring... 01-05-2013, 03:33 AM

nateman_doo Why? Its just a pulse of... 01-05-2013, 04:24 AM

SCzEngrgGroup The motor signals will induce... 01-05-2013, 05:54 AM

691175002 Ray is right, it is bad form... 01-05-2013, 07:33 AM

nateman_doo Is that the "driver watchdog... 01-05-2013, 03:40 PM

Fastest1 Start with a good star... 01-05-2013, 04:33 PM

nateman_doo The table is completely... 01-05-2013, 05:33 PM

DRock So how do you guys properly... 01-06-2013, 12:30 AM

SCzEngrgGroup For safety, securely ground... 01-06-2013, 02:08 AM

nateman_doo I thought home switches... 01-06-2013, 02:22 AM

SCzEngrgGroup Home and limit switches can... 01-06-2013, 02:27 AM

691175002 Your BOB is not really... 01-06-2013, 02:35 AM

amishx64 If you are worried about... 01-06-2013, 02:50 AM

SCzEngrgGroup Those are all poor choices... 01-06-2013, 02:55 AM

amishx64 Solid core? Not necesarially... 01-06-2013, 03:46 AM

TechGuy5002 Not really. Stranded wire is... 01-07-2013, 03:22 PM

DRock You guys are the best. ... 01-06-2013, 03:18 AM

nateman_doo For my Y, i can use solid... 01-06-2013, 03:32 AM

Fastest1 Cat 5 & 6 both come either... 01-06-2013, 04:53 AM

DRock This was better in the... 01-06-2013, 06:35 AM

nateman_doo Wait... what happened?? I... 01-06-2013, 10:28 AM

DRock Some mod decided this wasn't... 01-06-2013, 03:37 PM

idahogary no offense but you are wrong.... 01-06-2013, 04:12 PM

nateman_doo AWESOMESAUCE 01-06-2013, 10:20 AM

vcatalasan I have never used a bump... 01-06-2013, 10:37 AM

nateman_doo I don't think the motor is... 01-06-2013, 04:57 PM

vcatalasan How does Mach3 know where the... 01-06-2013, 08:52 PM

nateman_doo Once you know your work... 01-06-2013, 11:19 PM

Fastest1 It doesn't, you have to re... 01-06-2013, 09:48 PM

nateman_doo CNC Movement, hand powered.... 01-06-2013, 11:27 PM

nateman_doo Finished the wire carrier for... 01-07-2013, 02:11 AM

amishx64 Wow nice work. That is really... 01-07-2013, 02:22 AM

nateman_doo Honestly I don't know much... 01-07-2013, 01:41 PM

cjsamples VFD 01-07-2013, 02:12 PM

More replies below current depth...

BAMCNC.COM I don't have limits, I use... 01-07-2013, 03:25 AM

Fastest1 Without referencing since you... 01-07-2013, 01:36 PM

ErnieD nateman, ... 01-07-2013, 04:31 PM

nateman_doo I remember reading, or... 01-07-2013, 07:32 PM

keebler303 Any decent VFD (not ebay... 01-07-2013, 08:29 PM

nateman_doo I remember looking at these a... 01-07-2013, 10:47 PM

BAMCNC.COM Your telling me I don't do... 01-07-2013, 09:34 PM

keebler303 He didn't say you don't do... 01-07-2013, 10:05 PM

cjsamples Teco FM50 01-07-2013, 10:34 PM

nateman_doo Speaking of which, tell me... 01-07-2013, 10:34 PM

keebler303 A charge pump circuit on a... 01-08-2013, 04:46 PM

nateman_doo Wiring for the table is... 01-08-2013, 06:04 AM

nateman_doo Shower pan liner, and some... 01-08-2013, 04:29 PM

nateman_doo Nice. How much processing... 01-08-2013, 04:54 PM

keebler303 No idea. Only ever used it on... 01-08-2013, 05:10 PM

nateman_doo Dude.... of COURSE i rock... 01-08-2013, 05:48 PM

Zach_G Mach3 has a charge pump... 01-08-2013, 05:31 PM

nateman_doo Isn't a sensor supposed to go... 01-08-2013, 07:31 PM

keebler303 V/Hz is the cheapest control... 01-08-2013, 07:51 PM

keebler303 I'd recommend an MP3 player... 01-08-2013, 05:59 PM

nateman_doo Then its probably whatever... 01-08-2013, 06:58 PM

keebler303 If your computer is... 01-08-2013, 07:39 PM

nateman_doo Figured faster processors... 01-08-2013, 07:48 PM

nateman_doo So the sensorless vector will... 01-09-2013, 12:03 AM

nateman_doo here is the motor specs:... 01-09-2013, 02:22 AM

keebler303 The 1/100 etc. is just a rule... 01-09-2013, 03:54 AM

nateman_doo 34 RPM is pretty slow. I... 01-09-2013, 06:37 AM

nateman_doo I also noticed that they... 01-09-2013, 01:02 PM

Bloy2004 Very nice mill bed/table... 01-09-2013, 02:29 PM

nateman_doo Thanks! I am especially... 01-09-2013, 03:08 PM

Bloy2004 post deleted. please... 01-09-2013, 03:48 PM

nateman_doo What observation? 01-09-2013, 04:27 PM

nateman_doo I read an interesting paper... 01-09-2013, 04:26 PM

keebler303 Mach can't handle the high... 01-09-2013, 04:34 PM

nateman_doo Can you elaborate on that? 01-09-2013, 05:08 PM

keebler303 Encoder basics:... 01-09-2013, 06:04 PM

Al_The_Man I see in the link they show... 01-14-2013, 07:18 PM

keebler303 Let's not start talking about... 01-14-2013, 07:53 PM

nateman_doo probably a bit over my head -... 01-09-2013, 06:21 PM

keebler303 I wasn't suggesting you buy... 01-09-2013, 07:14 PM

nateman_doo I guess its something I have... 01-09-2013, 11:29 PM

cjsamples Yeah.......Hurry up!! I want... 01-09-2013, 11:47 PM

nateman_doo Thanks! I am QUITE pleased... 01-10-2013, 02:06 AM

nateman_doo Made the goal of finishing... 01-10-2013, 06:21 AM

vcatalasan I like! your moving right... 01-10-2013, 08:20 AM

nateman_doo Yup, thats the exact thing I... 01-10-2013, 02:07 PM

nateman_doo For some reason I can't get... 01-11-2013, 06:14 AM

nateman_doo Just ordered the GS3 SL/V... 01-11-2013, 04:47 PM

rowbare Nate, The Tormach version... 01-11-2013, 05:07 PM

keebler303 I like Igus Shielded wire for... 01-11-2013, 06:06 PM

nateman_doo Z axis plates/spindle mounts 01-12-2013, 09:31 PM

nateman_doo The spindle control and gecko... 01-13-2013, 06:18 AM

the4thseal Remember to add non shrinking... 01-14-2013, 05:22 AM

nateman_doo Can you tell me more about... 01-14-2013, 06:58 PM

nateman_doo Thats a bit over my head. ... 01-14-2013, 08:25 PM

keebler303 8020 (another company I love... 01-14-2013, 08:46 PM

nateman_doo ok, MUCH better explanation. ... 01-14-2013, 08:48 PM

nateman_doo I just threw a bag of the... 01-15-2013, 05:38 AM

nateman_doo Packed 2 of the upright... 01-15-2013, 06:28 PM

nateman_doo The weight of the beams went... 01-15-2013, 07:54 PM

nateman_doo I would be lying if I said i... 01-16-2013, 07:27 AM

cjsamples Ah, the hurry-ups has finally... 01-16-2013, 08:43 AM

Bloy2004 Is that the GS22PO model? ... 01-16-2013, 01:09 PM

nateman_doo GS3-22P0 All at... 01-16-2013, 05:37 PM

nateman_doo I am terrified of that. I am... 01-16-2013, 07:50 PM

nateman_doo Just scored the additional... 01-16-2013, 08:10 PM

cjsamples Z axis 01-16-2013, 11:56 PM

nateman_doo Those 12" x 24X plates will... 01-17-2013, 04:37 AM

LeeWay That should work very well.... 01-17-2013, 01:09 PM

keebler303 I put an SSD in my laptop and... 01-17-2013, 03:10 PM

nateman_doo Yea, the SSD is the single... 01-17-2013, 05:43 PM

nateman_doo This VFD wiring is staring at... 01-18-2013, 12:53 AM

cjsamples huh? 01-18-2013, 04:38 AM

nateman_doo There is so much going on... 01-18-2013, 02:10 PM

nateman_doo The computer w/all the... 01-18-2013, 02:47 PM

keebler303 You have a link to the BOB... 01-18-2013, 03:45 PM

cjsamples C11 board 01-18-2013, 07:48 PM

nateman_doo http://cnc4pc.com/Tech_Docs/C1... 01-18-2013, 08:16 PM

keebler303 The isolated output is for... 01-18-2013, 08:50 PM

keebler303 The AC connections are... 01-18-2013, 09:31 PM

Al_The_Man If there is no scaling in the... 01-18-2013, 10:29 PM

nateman_doo I was hoping those 2 relays... 01-18-2013, 11:21 PM

nateman_doo Z axis is starting to take... 01-19-2013, 04:45 AM

cjsamples C11 can be used ot control... 01-19-2013, 04:51 AM

cjsamples pdf 01-19-2013, 05:08 AM

nateman_doo Its a brand new thing for me,... 01-19-2013, 05:46 AM

cjsamples Sweet 01-19-2013, 09:14 PM

nateman_doo Thanks! I made a dxf of the... 01-19-2013, 10:47 PM

nateman_doo Ok, closer to 5° as my math... 01-20-2013, 04:04 AM

nateman_doo In the spirit of daily... 01-20-2013, 11:41 PM

nateman_doo Last update for the night:... 01-21-2013, 06:54 AM

mikemaat Any tips on... 01-21-2013, 06:25 PM

nateman_doo Vise grips, with something... 01-21-2013, 07:06 PM

mikemaat The other end of the screw is... 01-21-2013, 07:23 PM

nateman_doo no sophistication at all. ... 01-21-2013, 08:19 PM

mikemaat Nothing wrong with keeping it... 01-21-2013, 08:27 PM

nateman_doo I hardly feel I am in any... 01-22-2013, 01:11 PM

LeeWay I used 3060 80/20 as the... 01-22-2013, 01:47 PM

nateman_doo Granted its not broke, but do... 01-22-2013, 03:36 PM

nateman_doo I was looking at your build. ... 01-22-2013, 04:15 PM

LeeWay Are you talking about this... 01-23-2013, 05:21 PM

nateman_doo <<<THREAD... 01-22-2013, 08:34 PM

nateman_doo I just found out the spindle... 01-22-2013, 09:15 PM

nateman_doo After a painful evening, here... 01-23-2013, 06:39 AM

nateman_doo After a painful evening, here... 01-23-2013, 06:39 AM

nateman_doo Deflection calculations -... 01-23-2013, 04:33 PM

nateman_doo Yup, that one. I just did a... 01-23-2013, 06:43 PM

LeeWay Yeah. For an aluminum spine,... 01-24-2013, 03:43 PM

nateman_doo I am very pleased. I hang on... 01-24-2013, 04:07 PM

LeeWay I'll tell you how you can... 01-24-2013, 07:17 PM

nateman_doo I put a machinist level on... 01-25-2013, 06:39 AM

nateman_doo Side note... While I was... 01-25-2013, 07:54 PM

keebler303 What drives are you using... 01-25-2013, 08:08 PM

LeeWay2 Stepper motors can get hot... 01-25-2013, 10:00 PM

nateman_doo hot enough that when I... 01-26-2013, 01:17 AM

LeeWay2 That does sound a bit too... 01-26-2013, 01:24 AM

nateman_doo I love having a REAL computer... 01-26-2013, 08:36 PM

nateman_doo meh.... mission accomplished?... 01-27-2013, 03:11 PM

LeeWay2 You are aware that 5/16"... 01-27-2013, 03:18 PM

nateman_doo Yup, i bought 2 boxes of drop... 01-27-2013, 05:25 PM

LeeWay2 I just use standard carriage... 01-27-2013, 05:35 PM

nateman_doo For the Z plates I think I... 01-27-2013, 05:53 PM

nateman_doo I will finally have some... 01-30-2013, 02:31 AM

nateman_doo A random cross section of one... 01-30-2013, 02:08 PM

nateman_doo I forgot the mention, the 4... 01-30-2013, 09:12 PM

691175002 I know that using bolts to... 01-30-2013, 09:26 PM

nateman_doo You are correct. i am not a... 01-30-2013, 11:11 PM

nateman_doo I feel like my arm is going... 01-31-2013, 06:50 AM

nateman_doo Both Z beams are installed,... 02-01-2013, 01:40 AM

nateman_doo So here is the Z base plate... 02-01-2013, 06:36 AM

keebler303 I like that you freshly faced... 02-01-2013, 03:52 PM

nateman_doo TELL me about it. The X0Y0... 02-04-2013, 05:39 PM

nateman_doo The drop in nuts arrived... 02-05-2013, 03:21 PM

nateman_doo Installed some Z axis stuff. ... 02-06-2013, 06:34 AM

nateman_doo Lots of progress last night. ... 02-06-2013, 02:50 PM

cjsamples Good stuff there Nate. It is... 02-06-2013, 07:27 PM

nateman_doo Thanks! I have to attach a... 02-06-2013, 08:14 PM

nateman_doo In order to adjust the back... 02-07-2013, 06:16 AM

nateman_doo http://pbr590.photobucket.com/... 02-09-2013, 01:33 AM

nateman_doo ugh, I think my X2 motor... 02-13-2013, 01:10 AM

cjsamples Update? 02-16-2013, 06:51 PM

nateman_doo Nice to know you care :) ... 02-17-2013, 06:08 PM

nateman_doo The only sad update I have... 02-22-2013, 01:37 AM

nikkocortez Amazing! 02-22-2013, 08:09 AM

nateman_doo I will finally have some... 03-01-2013, 02:03 AM

nateman_doo I just figured out what I am... 03-01-2013, 03:55 AM

nateman_doo After a really long break, I... 03-01-2013, 05:28 AM

nateman_doo Counterweight is done! it... 03-02-2013, 10:50 PM

nateman_doo im almost done taking up the... 03-03-2013, 08:26 AM

cjsamples Pics are good....... 03-03-2013, 01:12 PM

nateman_doo I still have to finish the... 03-03-2013, 02:52 PM

LeeWay I think it is very cool. I... 03-03-2013, 03:04 PM

nateman_doo Or a rotary 4th axis. i was... 03-04-2013, 04:53 AM

Guest I see the forum got a face... 03-06-2013, 05:01 AM

nateman_doo Finally an update!... 03-14-2013, 03:41 AM

nateman_doo Got the drainage situation... 03-15-2013, 02:47 PM

cjsamples Not a big fan of the new... 03-15-2013, 02:53 PM

nateman_doo The drain is right now... 03-15-2013, 06:06 PM

nateman_doo Ran electric, and finally... 03-17-2013, 03:33 PM

nateman_doo Ran 220 to a small box:... 03-18-2013, 06:39 PM

nateman_doo 4 hours of hand mixing almost... 03-21-2013, 02:09 AM

Guest Pics are pretty good, but not... 03-21-2013, 03:07 AM

Guest Pics are pretty good, but not... 03-21-2013, 01:05 PM

nateman_doo No one has any input on... 03-22-2013, 03:24 PM

Bubba I have always used 7 days for... 03-22-2013, 03:48 PM

nateman_doo Did the forums change again?! 03-24-2013, 10:45 PM

the4thseal It changes every time I log... 03-25-2013, 03:22 AM

nateman_doo I made it pretty soupy, but... 03-24-2013, 10:40 PM

nateman_doo This is slightly better then... 03-25-2013, 05:42 PM

keebler303 Do you have your drain glued... 03-25-2013, 09:07 PM

nateman_doo everything is glued from the... 03-26-2013, 01:26 AM

keebler303 If you are drilling or... 03-26-2013, 04:11 AM

nateman_doo most of the holes I drill are... 03-26-2013, 04:44 AM

LeeWay Looking good. I think I... 03-26-2013, 09:36 AM

nateman_doo The whole shebang will be... 03-26-2013, 02:02 PM

LeeWay Sounds like that will work... 03-26-2013, 02:25 PM

nateman_doo My wife is going to shoot me... 03-26-2013, 04:29 PM

keebler303 Give her the credit card and... 03-26-2013, 07:07 PM

nateman_doo She knows its coming. I told... 03-26-2013, 08:48 PM

LeeWay Yeah, make sure it is vented... 03-26-2013, 09:22 PM

nateman_doo http://www.lowes.com/pd_72067-... 03-28-2013, 12:21 AM

marzetti I'm not sure about that one.... 03-28-2013, 02:13 AM

nateman_doo Nope, I live in Jersey. Id... 03-28-2013, 12:13 PM

BAMCNC.COM Yes? You called? Lol, I... 03-27-2013, 01:51 AM

keebler303 Yeah, Nate, seriously. Get a... 03-27-2013, 03:14 AM

nateman_doo especially if I tell them to... 03-27-2013, 03:45 AM

cjsamples Looking good Nate. You will... 03-27-2013, 08:29 PM

nateman_doo Im dying to see what its... 03-27-2013, 10:42 PM

keebler303 Nate Anything is better... 03-28-2013, 02:33 AM

nateman_doo Doing the resin/sand today. ... 03-29-2013, 01:46 PM

nateman_doo Survived the first round. ... 03-29-2013, 06:04 PM

amishx64 YAY! 03-29-2013, 06:37 PM

nateman_doo yay to pics, or yay I will... 03-29-2013, 10:36 PM

nateman_doo A very boring wet video ... 03-30-2013, 01:25 AM

keebler303 Looking good. 03-30-2013, 04:03 AM

outsider787 Looks great! Did you epoxy... 03-30-2013, 06:57 PM

nateman_doo Thanks! The first step was to... 03-31-2013, 12:30 AM

nateman_doo Touched up on some of the... 04-07-2013, 10:27 PM

LeeWay Because of this thread, I may... 04-07-2013, 11:52 PM

nateman_doo Why not have BOTH?? I... 04-08-2013, 01:03 AM

nateman_doo I am trying to wire up the... 04-08-2013, 04:31 PM

keebler303 On the analog, you are... 04-08-2013, 08:35 PM

cjsamples Nate, You can run your VFD... 04-08-2013, 08:57 PM

Al_The_Man There is a later plug in for... 04-08-2013, 09:47 PM

nateman_doo This is my X2 board:... 04-09-2013, 12:26 AM

nateman_doo I hate to say you confused me... 04-09-2013, 12:19 AM

nateman_doo ordering 25 of them: 2N7000... 04-15-2013, 06:42 PM

nateman_doo So back to this... 184284 ... 05-10-2013, 12:57 AM

nateman_doo This is where 2n7000 came up. 05-13-2013, 06:17 PM

keebler303 RS-485 is just another serial... 04-08-2013, 09:26 PM

Topdecking Well if you do that on all... 04-10-2013, 05:55 PM

keebler303 Ha, I can try. The analog... 04-09-2013, 01:59 AM

nateman_doo Its slowly sinking in (see... 04-09-2013, 03:04 AM

Victoria602 Because of this thread, I may... 04-09-2013, 03:18 AM

keebler303 Yeah, you need to buy the... 04-09-2013, 02:27 PM

nateman_doo Way to rain on my parade?! ... 04-09-2013, 07:19 PM

Bubba BRILLIANT, FRIGGING... 04-09-2013, 02:28 PM

keebler303 I'd buy 10 for the... 04-09-2013, 08:13 PM

nateman_doo I love the idea, but I don't... 04-10-2013, 04:44 PM

keebler303 Nate You could use thin... 04-10-2013, 05:23 PM

nateman_doo I ordered an EPMD rubber... 04-11-2013, 01:52 PM

nateman_doo The Constant force spring was... 04-13-2013, 05:36 AM

nateman_doo Finished the rear bellows:... 04-14-2013, 02:17 PM

nateman_doo Silly question... Has anyone... 04-19-2013, 03:38 PM

outsider787 I've connected to the mach3... 04-19-2013, 04:08 PM

nateman_doo I got something called Team... 04-23-2013, 03:16 PM

nateman_doo Finally managed to wire up... 04-29-2013, 02:15 PM

nateman_doo Finally tried out the X way... 04-30-2013, 08:39 PM

Fastest1 I think if you connected the... 04-30-2013, 11:16 PM

nateman_doo I have thought of that, but... 05-01-2013, 01:34 PM

keebler303 Nate, you know the control... 05-01-2013, 02:18 PM

Bloy2004 Nate, Have you explored the... 05-01-2013, 02:51 PM

nateman_doo Thats really not a half bad... 05-01-2013, 06:35 PM

nateman_doo The start of the right sides... 05-03-2013, 02:23 PM

keebler303 Nate I am not sure you are... 05-03-2013, 03:45 PM

nateman_doo fair enough. I will take a... 05-03-2013, 06:15 PM

nateman_doo http://i590.photobucket.com/al... 05-04-2013, 03:40 AM

nateman_doo Ta daaaaa:... 05-04-2013, 05:40 AM

nateman_doo Love it? hate it? What say... 05-04-2013, 06:21 PM

mrquacker That I ran across this thread... 05-05-2013, 02:19 AM

nateman_doo Nope, I actually have some... 05-05-2013, 06:02 AM

keebler303 You can kind of see it here.... 05-06-2013, 02:55 PM

BAMCNC.COM Love it! 05-05-2013, 02:36 AM

keebler303 With regard to the springs,... 05-06-2013, 02:53 PM

nateman_doo I appreciate the candor. I... 05-08-2013, 02:31 AM

keebler303 Without looking back at the... 05-08-2013, 02:39 AM

nateman_doo CNC4PC... 05-08-2013, 02:48 AM

nateman_doo The first 7 pins are green in... 05-08-2013, 03:48 AM

nateman_doo Here is what I think my... 05-08-2013, 04:35 AM

nateman_doo http://i590.photobucket.com/al... 05-08-2013, 05:38 AM

nateman_doo The last 2 pictures are of... 05-08-2013, 03:08 PM

keebler303 There is an enable input on... 05-08-2013, 03:31 PM

keebler303 Also, section 6.1. Disable... 05-08-2013, 03:39 PM

nateman_doo I have the 5V on the top left... 05-08-2013, 03:42 PM

keebler303 The pin header jumper for the... 05-08-2013, 03:47 PM

nateman_doo 183956 As in the circled... 05-08-2013, 03:56 PM

keebler303 NATE! I think you need 5V... 05-08-2013, 04:13 PM

Al_The_Man Ironically this displays the... 05-09-2013, 04:13 AM

nateman_doo First step, was adding the 5... 05-09-2013, 04:26 AM

nateman_doo Not to mention, they all... 05-09-2013, 04:46 AM

keebler303 Nate The point is that the... 05-09-2013, 01:52 PM

keebler303 In the variable speed control... 05-09-2013, 01:47 PM

keebler303 OK, I was confused there. ... 05-08-2013, 04:07 PM

Bubba Dumb question! You indicate... 05-08-2013, 04:11 PM

nateman_doo oh crap... the USB is for the... 05-08-2013, 05:04 PM

keebler303 I agree it is not a very good... 05-08-2013, 05:22 PM

cjsamples Nate, You don't have enough... 05-08-2013, 07:35 PM

cjsamples Jumper on the first 2 is... 05-08-2013, 07:39 PM

Al_The_Man See another similar issue... 05-08-2013, 09:34 PM

keebler303 The blind leading the blind,... 05-08-2013, 09:37 PM

nateman_doo I have them installed. ... 05-08-2013, 07:41 PM

cjsamples oh, they are very light in... 05-08-2013, 07:45 PM

nateman_doo side note, thanks for all the... 05-08-2013, 08:02 PM

nateman_doo what do you mean jumper at... 05-08-2013, 08:00 PM

cjsamples ThunderDork » DIY CNC Router... 05-08-2013, 08:01 PM

cjsamples attached photo. Driver needs... 05-08-2013, 08:05 PM

cjsamples Can you post a photo of the... 05-08-2013, 08:07 PM

cjsamples 5 volt to top left, 12V to... 05-08-2013, 08:11 PM

cjsamples 5 volt to top left, 12V to... 05-08-2013, 08:18 PM

keebler303 NO!!!!!!!!!! - - - Updated... 05-08-2013, 08:39 PM

keebler303 You need the USB 5V to the... 05-08-2013, 08:41 PM

cjsamples Page 18 of the C11 manual.... 05-08-2013, 08:48 PM

keebler303 You may be right, I don't own... 05-08-2013, 08:58 PM

keebler303 Page 18 talks about the 12V... 05-08-2013, 09:00 PM

cjsamples Keebler, the manual shows 12V... 05-08-2013, 08:45 PM

cjsamples Here is a photo of where I am... 05-08-2013, 08:59 PM

cjsamples The board is a great board. I... 05-08-2013, 09:01 PM

nateman_doo http://i590.photobucket.com/al... 05-08-2013, 10:33 PM

cjsamples on my board I have the three... 05-08-2013, 11:20 PM

cjsamples Nate, Are those pairs of... 05-08-2013, 11:38 PM

nateman_doo http://youtu.be/eQj_lWQwc0I... 05-09-2013, 04:17 AM

Gr6Burns I have mine on a common... 05-09-2013, 07:48 AM

nateman_doo I measured the backlash of... 05-09-2013, 12:40 PM

Al_The_Man The other irony of course is... 05-09-2013, 04:23 PM

keebler303 Al Could you explain a... 05-09-2013, 06:06 PM

Al_The_Man A General Definition: ... 05-09-2013, 07:13 PM

keebler303 Thanks Al. So even though... 05-09-2013, 08:09 PM

nateman_doo I agree. At least the motors... 05-09-2013, 04:57 PM

keebler303 You can have the switch and... 05-09-2013, 05:59 PM

Al_The_Man I have not read all the... 05-09-2013, 05:59 PM

nateman_doo here is what I am talking... 05-09-2013, 07:05 PM

keebler303 That is actually some quality... 05-09-2013, 07:21 PM

Bubba nateman, If I were to do... 05-09-2013, 07:24 PM

nateman_doo But what triggers it in Mach?... 05-09-2013, 08:12 PM

keebler303 Bear with me, it's been a... 05-09-2013, 08:41 PM

Bubba That is a picture that I... 05-09-2013, 08:40 PM

nateman_doo So I have been reading this... 05-10-2013, 03:20 AM

keebler303 As you drew it should work.... 05-10-2013, 05:00 AM

nateman_doo heh... good point. small... 05-10-2013, 05:15 AM

nateman_doo So I hooked everything up,... 05-11-2013, 06:44 AM

nateman_doo I hear a relay click on when... 05-11-2013, 08:48 AM

Fastest1 You hear a click? Can you run... 05-11-2013, 03:28 PM

nateman_doo it takes the 12V input and... 05-11-2013, 06:49 PM

Al_The_Man You could run each function... 05-11-2013, 07:02 PM

nateman_doo Im not using a pot, just the... 05-11-2013, 09:45 PM

Al_The_Man What I meant was if the relay... 05-11-2013, 10:18 PM

Bubba Nuther dumb question: Has... 05-11-2013, 10:23 PM

cjsamples Bubba is probably on the... 05-12-2013, 12:09 AM

nateman_doo Can you clarify? The input... 05-12-2013, 12:27 AM

cjsamples in your VFD manual see if one... 05-12-2013, 12:33 AM

Bubba OK, I mis read the situation.... 05-12-2013, 12:34 AM

cjsamples quick answer looks to be... 05-12-2013, 12:37 AM

nateman_doo let me go check. Then I will... 05-12-2013, 01:29 AM

cjsamples Bubba, I think you read it... 05-12-2013, 12:39 AM

cjsamples Nate, The BOB will act as... 05-12-2013, 12:55 AM

cjsamples If you are hearing a click,... 05-12-2013, 01:00 AM

Al_The_Man One other thing is to make... 05-12-2013, 01:09 AM

cjsamples From the manual I am reading... 05-12-2013, 01:16 AM

nateman_doo I set it 3 to the external... 05-12-2013, 02:00 AM

Al_The_Man The manual I am looking at... 05-12-2013, 02:44 AM

cjsamples Al, I was picking p3.00 to... 05-12-2013, 04:22 AM

nateman_doo Which reminds me, there is no... 05-13-2013, 12:38 AM

cjsamples When you hit the stop button,... 05-13-2013, 02:07 AM

nateman_doo thanks! i will be able to... 05-13-2013, 03:02 AM

Ronal2dduff I already got the evil eye... 05-13-2013, 10:10 AM

nateman_doo The X axis works perfectly... 05-13-2013, 02:10 PM

nateman_doo Another thing that blows my... 05-13-2013, 02:22 PM

keebler303 Nate, the duplicates are so... 05-13-2013, 03:30 PM

cjsamples Are your bump switches... 05-13-2013, 02:31 PM

nateman_doo the bump switches are wired... 05-13-2013, 03:06 PM

keebler303 It sounds like you want to... 05-13-2013, 03:38 PM

cjsamples Keebler is dead on about... 05-13-2013, 03:51 PM

nateman_doo 184656 my full schematic... 05-13-2013, 04:26 PM

keebler303 Looks good overall. As CJ is... 05-13-2013, 04:47 PM

cjsamples ok, did not see the... 05-13-2013, 04:58 PM

cjsamples Ok, on looking at it again, I... 05-13-2013, 05:09 PM

cjsamples Maybe I am seeing this wrong... 05-13-2013, 05:14 PM

Al_The_Man I see you are using the... 05-13-2013, 04:52 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-25-2023, 04:49 AM

cjsamples Nate, Look at how they have... 05-13-2013, 03:49 PM

nateman_doo I am not 100% on what your... 05-13-2013, 03:54 PM

cjsamples The BOB needs to see a ground... 05-13-2013, 04:01 PM

nateman_doo There must be a setting for... 05-13-2013, 04:27 PM

Al_The_Man Sink/Source explanation.... 05-13-2013, 04:18 PM

cjsamples That bit of reading will take... 05-13-2013, 04:23 PM

cjsamples Those limit switches HAVE to... 05-13-2013, 04:34 PM

keebler303 On the VFD.... The analog... 05-13-2013, 04:42 PM

cjsamples There is a big warning under... 05-13-2013, 04:55 PM

Al_The_Man The input power is internal... 05-13-2013, 05:00 PM

cjsamples The manual has a simple... 05-13-2013, 05:28 PM

nateman_doo those 2 small things in... 05-13-2013, 05:49 PM

Al_The_Man Looking at the (very poorly... 05-13-2013, 05:52 PM

nateman_doo So DCM goes to the GND pin... 05-13-2013, 06:15 PM

cjsamples No. The VFD doesn't want any... 05-13-2013, 06:48 PM

cjsamples I was kind of wondering why... 05-13-2013, 05:58 PM

Al_The_Man Lot of misunderstanding here,... 05-13-2013, 06:18 PM

nateman_doo Tell me about it. I am... 05-13-2013, 06:54 PM

keebler303 I like your switches but they... 05-13-2013, 07:08 PM

keebler303 I'm not sure what kind of... 05-13-2013, 07:16 PM

cjsamples What he said, wire a ground... 05-13-2013, 11:05 PM

More replies below current depth...

nateman_doo The table is electrically... 05-13-2013, 07:07 PM

nateman_doo A view of the bump switches:... 05-13-2013, 09:52 PM

Al_The_Man By rights you should try and... 05-13-2013, 10:21 PM

cjsamples The rs-### I could not... 05-13-2013, 11:09 PM

nateman_doo Almost 5M ohms between the... 05-13-2013, 11:22 PM

cjsamples what were the numbers on the... 05-13-2013, 11:47 PM

nateman_doo The gnd pin between 12 & 13. ... 05-14-2013, 12:51 AM

cjsamples Nate, If you want to have... 05-13-2013, 11:44 PM

nateman_doo Yep, i plan to run the input... 05-14-2013, 12:15 AM

cjsamples Ok, was the meter on the Ohm... 05-14-2013, 12:55 AM

nateman_doo Bump switches...check.... 05-14-2013, 04:42 AM

cjsamples Now if we can just get that... 05-14-2013, 04:47 AM

cjsamples Did you try to wire it up... 05-14-2013, 04:53 AM

cjsamples Mach3, ports and pins, Second... 05-14-2013, 04:59 AM

nateman_doo nope. Focused on the homing... 05-14-2013, 05:00 AM

cjsamples I am more of a night owl so I... 05-14-2013, 05:02 AM

Gar33nett Look at the screen shot on... 05-14-2013, 07:14 AM

keebler303 Nate I would suggest... 05-14-2013, 03:06 PM

nateman_doo yes please... rehash would be... 05-14-2013, 04:25 PM

cjsamples Nate, read post 545 and see... 05-14-2013, 04:47 PM

keebler303 Yes, that part of the manual... 05-14-2013, 05:14 PM

keebler303 Nate If you have the VFD... 05-14-2013, 05:28 PM

cjsamples Keebler is giving you the... 05-14-2013, 05:45 PM

cjsamples Nate, Until you get this... 05-14-2013, 05:52 PM

keebler303 Not a bad idea at all. :D ... 05-14-2013, 06:05 PM

cjsamples I did suggest 100 hz based on... 05-14-2013, 06:10 PM

Al_The_Man I admit I have not read all... 05-14-2013, 06:22 PM

nateman_doo The relays are for... 05-14-2013, 06:30 PM

Al_The_Man If they only have to run when... 05-14-2013, 06:38 PM

keebler303 The VFD "at speed" output is... 05-14-2013, 06:49 PM

keebler303 That is not a bad idea I... 05-14-2013, 06:36 PM

Al_The_Man ??I though the idea was to... 05-14-2013, 07:07 PM

keebler303 Nate asked about connecting... 05-14-2013, 07:12 PM

nateman_doo Now I feel like Forrest Gump.... 05-14-2013, 07:25 PM

keebler303 Yes, that is the current... 05-14-2013, 07:47 PM

nateman_doo HA! You guys are awesome. ... 05-14-2013, 08:01 PM

keebler303 No. Since you are using the... 05-14-2013, 08:15 PM

nateman_doo I will make this happen when... 05-14-2013, 08:41 PM

keebler303 Yes, it will accelerate at... 05-14-2013, 08:58 PM

Al_The_Man The relay output is only... 05-14-2013, 09:07 PM

Al_The_Man Yeah.... It's called moving... 05-14-2013, 08:04 PM

nateman_doo From the manufacturer: The... 05-14-2013, 08:39 PM

cjsamples Where in the he^^ did you see... 05-15-2013, 01:37 AM

nateman_doo ok, i have the DCM, to the... 05-15-2013, 03:52 AM

nateman_doo you guys kept saying... 05-15-2013, 03:59 AM

FannBlade Have you adjusted the output... 05-15-2013, 04:12 AM

nateman_doo Top spindle pulley OD: 1.945 ... 05-15-2013, 04:35 AM

keebler303 It is vital that you... 05-15-2013, 03:03 PM

nateman_doo I FINALLY got 10V out, when I... 05-15-2013, 04:26 AM

FannBlade I think 60 hz will be more in... 05-15-2013, 04:29 AM

Fastest1 The 3360 rpm rating would be... 05-15-2013, 04:52 AM

Fastest1 Btw, you aren't the first to... 05-15-2013, 04:56 AM

cjsamples p0.04 sets max rpm, p0.03 you... 05-15-2013, 04:57 AM

cjsamples OK, I HAVE TO YELL AT YOU... 05-15-2013, 04:59 AM

cjsamples :stickpoke Post #485,... 05-15-2013, 05:08 AM

nateman_doo http://www.youtube.com/watch?v... 05-15-2013, 12:27 PM

nateman_doo LOLOL!! i knnoowww i... 05-15-2013, 05:18 AM

cjsamples I have to head out the... 05-15-2013, 05:32 AM

cjsamples You have the paperwork for... 05-15-2013, 05:24 AM

nateman_doo What part of the mach setup... 05-15-2013, 08:26 PM

Fastest1 I believe the pulley ratios... 05-15-2013, 10:52 PM

keebler303 You setup the spindle in the... 05-15-2013, 10:58 PM

Al_The_Man MachMill Manual section... 05-15-2013, 11:22 PM

keebler303 When all else fails, RTFM! :D 05-15-2013, 11:48 PM

nateman_doo Now starts the steep learning... 05-16-2013, 02:02 AM

nateman_doo his settings, don't work for... 05-16-2013, 03:08 AM

nateman_doo I think I have it... but a... 05-16-2013, 03:54 AM

Al_The_Man Once the VFD P3.00 set to 01... 05-16-2013, 04:52 AM

nateman_doo Duplicate Function Error GS3... 05-16-2013, 05:43 AM

nateman_doo Nope. Duplicate Function. ... 05-16-2013, 05:16 AM

nateman_doo Spindle function - YouTube... 05-16-2013, 05:52 AM

cjsamples Just watched the mach/spindle... 05-16-2013, 09:02 AM

cjsamples Nate, Try this, Change... 05-16-2013, 08:59 AM

nateman_doo it doesn't change at all. ... 05-16-2013, 11:15 AM

nateman_doo IT WOORRRKKKKSSSS!! I just... 05-16-2013, 12:05 PM

cjsamples So, when do you want me to... 05-16-2013, 04:18 PM

nateman_doo heh. dxf? do you have a cad... 05-16-2013, 04:19 PM

cjsamples On the subject of your table... 05-16-2013, 06:03 PM

nateman_doo Just ordered a separate relay... 05-16-2013, 07:27 PM

nateman_doo The entire setup was designed... 05-16-2013, 07:00 PM

nateman_doo I am going through the DC... 05-17-2013, 03:34 AM

nateman_doo damn! my PC crashed, and I... 05-17-2013, 04:23 AM

Al_The_Man Did you try doing the VFD... 05-17-2013, 04:44 AM

nateman_doo as in spindle auto... 05-17-2013, 04:51 AM

cjsamples A wise man once told me to... 05-17-2013, 05:07 AM

cjsamples Nate, Go into mach and... 05-17-2013, 05:24 AM

cjsamples If you did not purchase a... 05-17-2013, 05:17 AM

nateman_doo I have a breaking resistor. ... 05-17-2013, 12:09 PM

Fastest1 I hope it is a braking... 05-17-2013, 12:19 PM

nateman_doo heh... good one. that... 05-17-2013, 02:29 PM

LeeWay Ohhh. Sounds like something... 05-17-2013, 02:35 PM

nateman_doo Its really just a roadblock. ... 05-17-2013, 03:32 PM

LeeWay Personally, I would stick... 05-17-2013, 03:44 PM

cjsamples Mach has a pop-up that tells... 05-17-2013, 03:55 PM

cjsamples Nate, Did you leave that... 05-17-2013, 04:00 PM

nateman_doo I didn't mess with those... 05-18-2013, 12:44 AM

nateman_doo well, I do mess around with... 05-17-2013, 05:58 PM

nateman_doo Plus there is no way for Mach... 05-21-2013, 12:52 AM

keebler303 I'm not sure about feedback... 05-21-2013, 03:52 AM

nateman_doo can you tell me a little... 05-21-2013, 04:29 AM

Fastest1 The tach he is referring to... 05-21-2013, 01:20 PM

nateman_doo I am 100% sure its a setting... 05-21-2013, 01:55 PM

keebler303 One way to achieve spindle... 05-21-2013, 02:29 PM

keebler303 Nate Can you post... 05-21-2013, 02:27 PM

nateman_doo I was thinking about that... 05-21-2013, 02:38 PM

Jere33my I am pretty sure 120 Hz... 05-21-2013, 03:28 PM

nateman_doo OK, great news. I just... 05-22-2013, 02:20 AM

keebler303 Do you mean 10000 RPM = 10V?... 05-22-2013, 02:41 PM

Al_The_Man If you mean that your actual... 05-22-2013, 03:26 PM

keebler303 The VFD needs adjustment so... 05-22-2013, 03:47 PM

nateman_doo what I mean, is in Mach when... 05-22-2013, 04:25 PM

nateman_doo Updated Schematic:185650 05-22-2013, 05:19 PM

keebler303 Setup the mach screens as... 05-22-2013, 06:35 PM

nateman_doo For some reason this isn't... 06-26-2013, 06:49 AM

keebler303 It's always on? Or once you... 06-26-2013, 03:30 PM

Fastest1 You will have to check the... 05-22-2013, 10:05 PM

nateman_doo 5 MONTHS later these finally... 05-27-2013, 10:07 PM

keebler303 5 months just for 80%? You... 05-28-2013, 04:24 PM

nateman_doo heh...I don't have the tools... 05-28-2013, 07:09 PM

keebler303 Threadmilling will knock out... 05-28-2013, 07:49 PM

nateman_doo I don't know anything about... 05-28-2013, 08:36 PM

keebler303 https://www.youtube.com/watch?... 05-28-2013, 09:02 PM

nateman_doo Awesome series! watched the... 05-29-2013, 05:15 AM

BAMCNC.COM I have two castings, wish I... 05-29-2013, 12:44 AM

nateman_doo Tore down the tubular counter... 05-29-2013, 05:47 AM

keebler303 The problem with the storm... 05-29-2013, 02:39 PM

nateman_doo I only need a bit over 100... 05-29-2013, 08:47 PM

mrquacker There is a conversation about... 05-29-2013, 08:57 PM

nateman_doo I firmly believe in the... 05-29-2013, 10:58 PM

keebler303 If you look in the motor... 05-30-2013, 03:11 AM

nateman_doo I did some experimental... 05-30-2013, 04:59 AM

Yaeg6erdg I think all of this matters... 05-30-2013, 07:30 AM

keebler303 That can be handled either... 05-30-2013, 02:16 PM

nateman_doo I am going to try one other... 05-30-2013, 03:12 PM

Al_The_Man You can get both types, but... 05-30-2013, 03:19 PM

keebler303 Yep. You'd connect the... 05-30-2013, 05:19 PM

nateman_doo I feel like there would be... 05-30-2013, 06:28 PM

keebler303 You should do that anyway.... 05-30-2013, 06:46 PM

nateman_doo Thats assuming my homing... 05-31-2013, 03:19 PM

keebler303 If it's important to you to... 05-31-2013, 04:40 PM

keebler303 Perfect! 05-31-2013, 04:34 PM

nateman_doo The homing I use just to set... 05-31-2013, 05:11 PM

Dylwad And you would still need to... 06-04-2013, 04:08 AM

nateman_doo Absolutly, whenever i restart... 06-04-2013, 04:31 PM

nateman_doo EXCELLENT POINT!!!!! I will... 06-04-2013, 02:24 AM

native34 What type of aluminum was... 06-07-2013, 09:10 PM

nateman_doo The bottom most slab (base)... 06-09-2013, 08:05 PM

native34 Will this machine be capable... 06-10-2013, 12:12 AM

Rachel635 I feel like there would be... 06-10-2013, 01:35 AM

nateman_doo both large slabs have been... 06-10-2013, 04:58 AM

nateman_doo Going into withdrawls not... 06-10-2013, 08:03 PM

nateman_doo Almost finished with the... 06-11-2013, 06:33 PM

nateman_doo half of the air/liquid... 06-18-2013, 12:15 AM

LeeWay Okay, what will that do? 06-18-2013, 12:18 AM

nateman_doo air on the left, liquid on... 06-18-2013, 12:33 AM

LeeWay I mean is it for coolant?... 06-18-2013, 12:40 AM

nateman_doo Yup. it will go around the... 06-18-2013, 02:15 AM

Dylwad Are you in sensorless vector... 06-18-2013, 02:27 AM

nateman_doo no, volt/hz mode. Sensorless... 06-18-2013, 02:47 AM

Dylwad Can you list your current vfd... 06-18-2013, 03:34 AM

nateman_doo that would take a while to... 06-18-2013, 05:22 AM

keebler303 There is a problem with your... 06-18-2013, 02:05 PM

nateman_doo I found out how to set the... 06-18-2013, 06:06 PM

keebler303 Nate You don't want the... 06-18-2013, 06:10 PM

nateman_doo there is an auto tuning... 06-18-2013, 06:17 PM

nateman_doo 2 weights did the trick:... 06-19-2013, 05:12 AM

nateman_doo Tonight I will likely mess... 06-19-2013, 04:23 PM

keebler303 Nate If you list what... 06-19-2013, 06:18 PM

nateman_doo heh... sure. I still have... 06-19-2013, 08:09 PM

nateman_doo WEE!!!! found all the... 06-22-2013, 03:48 AM

nateman_doo after a night of tinkering I... 06-22-2013, 06:06 AM

keebler303 Nate I don't remember what... 06-22-2013, 10:30 PM

nateman_doo calling it for the night. I... 06-22-2013, 08:07 AM

nateman_doo SO why would Tormach put a... 06-23-2013, 06:20 AM

keebler303 It's not that it only "does"... 06-24-2013, 12:23 PM

nateman_doo Automation Direct Sensorless... 06-24-2013, 06:46 PM

nateman_doo Just tried it out. the reset... 06-24-2013, 10:16 PM

Dylwad Chart for what? You should be... 06-24-2013, 10:22 PM

nateman_doo chart being: mach rpm freq... 06-25-2013, 03:07 AM

keebler303 I think you are getting... 06-25-2013, 03:31 AM

nateman_doo This is what I have right... 06-25-2013, 05:40 AM

nateman_doo http://www.youtube.com/watch?v... 06-25-2013, 03:48 AM

nateman_doo What the hell??? did the... 06-25-2013, 03:50 AM

nateman_doo I feel like the forums have... 06-25-2013, 06:02 AM

nateman_doo The coolant/air ring:... 06-25-2013, 08:06 PM

nateman_doo The smaller nozzles are for... 06-25-2013, 11:14 PM

LeeWay Ahah. ;) I was curious about... 06-26-2013, 01:46 AM

nateman_doo Same thing. On my X2 I put... 06-26-2013, 04:38 AM

nateman_doo I will mess around with the... 06-26-2013, 01:51 PM

FannBlade Great job on the cooler. How... 06-27-2013, 02:07 AM

Fastest1 Flood has always produced the... 06-26-2013, 02:55 PM

nateman_doo http://i590.photobucket.com/al... 06-26-2013, 08:59 PM

keebler303 Does the C15 board have an... 06-26-2013, 09:57 PM

nateman_doo I am in the general config...... 06-27-2013, 12:41 AM

nateman_doo M7 turns the spindle on at... 06-26-2013, 11:48 PM

LeeWay I think that is under ports... 06-27-2013, 12:45 AM

nateman_doo I am just an idiot. I had... 06-27-2013, 01:54 AM

nateman_doo Thanks! when u say make it,... 06-27-2013, 02:47 PM

LeeWay We used to make most of our... 06-27-2013, 02:52 PM

nateman_doo I have been doing 90 degree... 06-27-2013, 04:28 PM

LeeWay My MOS was combined while I... 06-30-2013, 03:26 PM

nateman_doo http://i590.photobucket.com/al... 06-29-2013, 07:31 AM

nateman_doo Started the initial tramming.... 06-30-2013, 05:57 AM

nateman_doo I did commo repair. I... 06-30-2013, 10:58 PM

nateman_doo http://i590.photobucket.com/al... 07-01-2013, 04:27 AM

nateman_doo I just noticed... the forums... 07-01-2013, 04:33 AM

nateman_doo Put 2 wood strips for the... 07-01-2013, 03:26 PM

nateman_doo Some of the bracing done last... 07-02-2013, 01:31 PM

BAMCNC.COM I find Dawn Dish Soap to be a... 07-03-2013, 12:35 AM

nateman_doo interesting. better then... 07-03-2013, 02:23 AM

Dylwad Linear rails are designed to... 07-03-2013, 02:31 AM

nateman_doo ? I got a case of... 07-03-2013, 03:23 AM

nateman_doo forgot to post this quick... 07-03-2013, 02:25 PM

nateman_doo Going to try an experiment. ... 07-03-2013, 04:22 PM

keebler303 I've rigged up an oil mist... 07-03-2013, 04:26 PM

nateman_doo Here I thought I was the only... 07-03-2013, 06:26 PM

steve123 It's great to see it move! ... 07-03-2013, 08:53 PM

nateman_doo Thanks!! yea, there is some... 07-04-2013, 03:22 AM

nateman_doo Man, look at the funky tool... 07-04-2013, 03:32 AM

Dylwad Nice, I used to try and pick... 07-04-2013, 04:05 AM

nateman_doo I only recently learned how... 07-04-2013, 04:39 AM

nateman_doo getting to about the 10th... 07-04-2013, 07:17 AM

nateman_doo Measured 135°F... 07-04-2013, 07:38 AM

Dylwad 135f is perfectly fine for a... 07-04-2013, 08:09 AM

nateman_doo X & Y motors are about 125°F... 07-04-2013, 08:22 AM

nateman_doo So i have accepted the... 07-06-2013, 06:20 AM

BAMCNC.COM Keep your velocity where it... 07-06-2013, 12:45 PM

nateman_doo Im not sure, they are gecko... 07-06-2013, 04:36 PM

nateman_doo They are geko 203V, and they... 07-06-2013, 06:40 PM

Fastest1 Gecko's formula (at least on... 07-06-2013, 07:07 PM

LeeWay I think the formula's are... 07-06-2013, 07:50 PM

nateman_doo Can u guys dumb that down a... 07-07-2013, 05:38 AM

LeeWay If it is only 4 wires on your... 07-07-2013, 02:32 PM

nateman_doo Counterbalance was... 07-08-2013, 06:34 AM

nateman_doo Here is the old pulley... 07-08-2013, 04:24 PM

nateman_doo I can't seem to access page... 07-08-2013, 04:58 PM

nateman_doo Anyone else having problems... 07-08-2013, 06:33 PM

keebler303 Page 63 working fine for... 07-08-2013, 09:01 PM

nateman_doo yea, works fine at home, but... 07-08-2013, 09:37 PM

nateman_doo continuing with the grueling... 07-08-2013, 11:13 PM

nateman_doo after EIGHT HOURS of... 07-09-2013, 06:03 AM

BAMCNC.COM Would of been done in atleast... 07-09-2013, 02:18 PM

nateman_doo hindsight is always 20/20. I... 07-09-2013, 02:37 PM

LeeWay For aluminum, I like to use... 07-09-2013, 02:42 PM

nateman_doo So where would I get some... 07-09-2013, 07:16 PM

Bubba Did a google for "1/2-13... 07-09-2013, 07:43 PM

Hack When I made something similar... 07-09-2013, 10:31 PM

BAMCNC.COM I use a Dewalt 12v impact and... 07-10-2013, 01:14 AM

nateman_doo I might end up using a... 07-10-2013, 03:54 AM

Dylwad +1 on the cordless... 07-10-2013, 04:06 AM

nateman_doo I took the tool plate off to... 07-10-2013, 06:10 AM

nateman_doo *edit* duplicate post ... 07-10-2013, 06:12 AM

nateman_doo Pics in the AM. Shopping... 07-11-2013, 07:12 AM

nateman_doo No idea whats going on with... 07-11-2013, 07:13 AM

nateman_doo And here comes the test... 07-11-2013, 01:23 PM

BAMCNC.COM Buy Irwin tap holders, no... 07-11-2013, 04:51 PM

nateman_doo I got it down to 7 seconds... 07-11-2013, 07:26 PM

nateman_doo I really dislike the bellows.... 07-12-2013, 04:26 AM

Bloy2004 I agree with you entirely. ... 07-15-2013, 04:54 PM

nateman_doo i think I came up with a... 07-12-2013, 08:09 AM

nateman_doo http://www.youtube.com/watch?v... 07-12-2013, 02:41 PM

nateman_doo The experiment worked. ... 07-12-2013, 11:14 PM

nateman_doo Yea... this is me drilling... 07-13-2013, 01:48 AM

BAMCNC.COM Hell yeah! 07-13-2013, 01:55 AM

nateman_doo Does anyone have any idea... 07-13-2013, 10:48 AM

LeeWay I think the bellows you have... 07-13-2013, 11:27 AM

nateman_doo I was thinking of... 07-15-2013, 01:01 PM

nateman_doo This is the way to go:... 07-16-2013, 01:13 AM

nateman_doo I put in a request for a... 07-16-2013, 04:03 PM

nateman_doo $220.00 each?!? man, thats... 07-17-2013, 07:36 PM

FannBlade Look at the price for... 07-18-2013, 12:47 AM

keebler303 These aren't what you are... 07-17-2013, 07:58 PM

nateman_doo None of the way covers in the... 07-19-2013, 01:36 AM

keebler303 Would tin snips help? ;) I... 07-19-2013, 02:49 AM

TaigCNCer I have the top way cover... 07-19-2013, 05:01 PM

nateman_doo I know its been quiet here,... 08-14-2013, 08:42 PM

Bloy2004 I would still consider... 08-15-2013, 12:46 PM

Dingenman Perhaps a new thread can be... 08-15-2013, 01:43 PM

nateman_doo YES PLEASE. I finally...... 08-24-2013, 02:40 PM

Billie3edick None of the way covers in the... 08-15-2013, 08:33 AM

nateman_doo So after thinking about it... 08-24-2013, 04:59 PM

keebler303 Nate Mcmaster will cut the... 08-25-2013, 03:38 PM

nateman_doo I returned those other... 08-25-2013, 04:14 PM

nateman_doo finally a new picture for... 08-26-2013, 02:17 AM

nateman_doo Lovely little inserts arrived... 08-31-2013, 05:04 AM

nateman_doo For the longest time i tried... 08-31-2013, 06:29 PM

nateman_doo ok, working on installing the... 09-02-2013, 04:24 AM

nateman_doo 3 hours later... ... 09-02-2013, 07:30 AM

nateman_doo Sexy right? Now I just have... 09-02-2013, 07:54 AM

nateman_doo http://www.youtube.com/watch?v... 09-02-2013, 08:56 AM

nateman_doo new bellows will arrive Wed. ... 09-02-2013, 04:27 PM

nateman_doo Ugh, it won't arrive until... 09-05-2013, 10:49 AM

nateman_doo http://i590.photobucket.com/al... 09-06-2013, 05:17 AM

Dylwad Im going with the glass is... 09-06-2013, 05:53 AM

keebler303 How are you gonna get those... 09-06-2013, 05:09 PM

nateman_doo actually back to the half... 09-06-2013, 11:43 PM

nateman_doo MUCH BETTER:... 09-07-2013, 04:53 AM

nateman_doo http://www.youtube.com/watch?v... 09-07-2013, 05:00 AM

nateman_doo air blast cleans it up... 09-06-2013, 06:13 PM

Hans_G Pretty awesome build you've... 09-06-2013, 09:25 PM

nateman_doo http://www.youtube.com/watch?v... 09-07-2013, 07:14 AM

The Blight That is pretty awesome :) 09-07-2013, 08:37 AM

nateman_doo http://i590.photobucket.com/al... 09-11-2013, 03:47 AM

diamond.3211 A little more in depth desc.... 09-11-2013, 04:01 AM

nateman_doo 3" R8 Carbide Indexable Face... 09-11-2013, 06:04 PM

keebler303 5 flutes at 1900 RPM is 9500... 09-11-2013, 06:30 PM

diamond.3211 I have attached a screen shot... 09-11-2013, 09:12 PM

nateman_doo BIIIIGGG difference:... 09-12-2013, 03:16 AM

FannBlade No I won't go there!! ... 09-12-2013, 02:55 PM

nateman_doo yes... I was just sitting in... 09-12-2013, 08:13 PM

Hack video!! 09-12-2013, 11:54 PM

nateman_doo I have to make a really nice... 09-13-2013, 01:09 PM

nateman_doo Its been a while since I have... 09-30-2013, 12:33 AM

nateman_doo Something I just learned... 10-04-2013, 03:19 AM

louieatienza Nice machine! Though... 10-05-2013, 12:04 AM

keebler303 Nate, regardless of your... 10-04-2013, 03:23 PM

nateman_doo So, back from the dead. ... 12-03-2013, 04:00 AM

nateman_doo So i have a REAALLLLYY weird... 12-04-2013, 06:39 AM

keebler303 Nate, that soulds like a mach... 12-04-2013, 05:29 PM

nateman_doo It does. the freq drops when... 12-04-2013, 07:49 PM

nateman_doo http://i590.photobucket.com/al... 12-06-2013, 08:55 PM

keebler303 Too bad it isn't living up to... 12-07-2013, 01:25 AM

TangentAudio He bolted that sucker to the... 12-07-2013, 09:05 PM

nateman_doo yea, it would be NO easy task... 12-09-2013, 04:19 PM

keebler303 I'll take what I can get! 12-09-2013, 07:33 PM

nateman_doo I still have to figure out... 12-10-2013, 09:06 PM

jsheerin What is your control setup... 12-10-2013, 10:09 PM

nateman_doo its listed in the countless... 12-18-2013, 07:48 PM

nateman_doo http://i590.photobucket.com/al... 12-18-2013, 08:07 PM

nateman_doo http://i590.photobucket.com/al... 12-20-2013, 03:08 PM

nateman_doo This is what I was talking... 01-07-2014, 04:25 AM

jsheerin I can't tell what's going... 01-07-2014, 06:49 AM

nateman_doo I also feel like it does a... 01-07-2014, 04:48 PM

keebler303 It is definitely mach or the... 01-07-2014, 07:00 PM

nateman_doo I will check the 0-10V output... 01-08-2014, 02:03 AM

keebler303 Mach outputs a pulse, the BOB... 01-08-2014, 04:45 PM

nateman_doo Broke my helical coupler. ... 01-08-2014, 04:00 PM

nateman_doo I think this is the reason:... 01-08-2014, 04:02 PM

nateman_doo I did check the output of the... 01-13-2014, 02:50 PM

nateman_doo http://i590.photobucket.com/al... 01-15-2014, 04:30 AM

arizonavideo Perhaps some salt or sand to... 01-15-2014, 09:23 AM

nateman_doo https://www.youtube.com/watch?... 01-16-2014, 05:22 AM

nateman_doo ...and something to help keep... 01-16-2014, 05:24 AM

nateman_doo Nope, they have to spin free.... 01-16-2014, 02:23 AM

nateman_doo Does anyone know where to buy... 01-16-2014, 09:15 PM

keebler303 Not sure if it's big enough... 01-16-2014, 11:18 PM

nateman_doo Those only go to 8". I am... 01-17-2014, 05:39 AM

FannBlade Here is an interesting thread... 01-17-2014, 12:28 AM

keebler303 Dura-Bar makes up to... 01-17-2014, 01:36 PM

spyderxxx I see table saws and lathes... 01-18-2014, 12:12 PM

LeeWay I was thinking the very same... 01-18-2014, 12:21 PM

nateman_doo You just might have a point... 01-18-2014, 02:53 PM

Fastest1 18x18 Linear Rail Tormach... 01-20-2014, 03:41 PM

LeeWay Not to say a bad word about... 01-20-2014, 04:28 PM

Fastest1 Is it a resonance issue. I... 01-21-2014, 02:14 PM

keebler303 It has to do with resonant... 01-21-2014, 08:49 PM

nateman_doo ...and I am sure having the... 01-22-2014, 12:55 AM

keebler303 These guys can provide you... 01-22-2014, 05:40 AM

nateman_doo Maybe I should rephrase. I... 01-22-2014, 08:25 PM

nateman_doo I found a HUGE chunk of steel... 01-23-2014, 01:34 AM

FannBlade It may need a coat of wax!... 01-23-2014, 01:41 AM

nateman_doo This would be a HUUGEEEE... 01-23-2014, 01:58 AM

LeeWay It will take a high amp... 01-23-2014, 02:23 AM

FannBlade @ LeeWay Wouldn't the heat... 01-23-2014, 02:58 AM

LeeWay Not if you or they use a... 01-23-2014, 06:09 AM

nateman_doo I could sit there for the... 01-23-2014, 02:53 PM

FannBlade That's true. I have also read... 01-23-2014, 03:07 PM

LeeWay You would certainly not need... 01-23-2014, 03:15 PM

keebler303 Or just find a local guy with... 01-23-2014, 03:35 PM

LeeWay It didn't really take me long... 01-23-2014, 03:44 PM

nateman_doo Thats why I didn't even... 01-23-2014, 04:55 PM

LeeWay If you watch for it,... 01-23-2014, 05:44 PM

nateman_doo I sent them a quote. So far... 01-23-2014, 07:43 PM

nateman_doo I just received word that the... 02-06-2014, 12:10 AM

keebler303 If rigidity is your goal, I'd... 02-06-2014, 09:01 PM

nateman_doo I just want the quill for... 02-07-2014, 08:30 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-27-2014, 06:06 PM

Hans_G Re: 18x18 Linear Rail Tormach... 03-27-2014, 06:40 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-27-2014, 10:29 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-28-2014, 01:53 AM

cjsamples Re: 18x18 Linear Rail Tormach... 03-28-2014, 09:14 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-30-2014, 07:11 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 06-04-2014, 05:00 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 06-04-2014, 04:58 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 06-05-2014, 04:28 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 06-09-2014, 02:45 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 07-09-2014, 08:29 PM

coils Re: 18x18 Linear Rail Tormach... 07-15-2014, 10:23 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 07-22-2014, 01:55 PM

coils Re: 18x18 Linear Rail Tormach... 07-23-2014, 02:33 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 07-30-2014, 08:49 PM

coils Re: 18x18 Linear Rail Tormach... 08-03-2014, 10:05 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 10-09-2014, 03:47 PM

coils Re: 18x18 Linear Rail Tormach... 10-09-2014, 10:19 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 10-31-2014, 05:34 AM

keebler303 Re: 18x18 Linear Rail Tormach... 10-31-2014, 02:21 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 11-03-2014, 07:15 PM

Hans_G Re: 18x18 Linear Rail Tormach... 11-03-2014, 09:15 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-17-2014, 05:47 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 01-14-2015, 05:16 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-02-2015, 05:45 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-02-2015, 06:48 AM

LeeWay Re: 18x18 Linear Rail Tormach... 02-02-2015, 12:39 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-02-2015, 04:11 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-05-2015, 02:21 AM

keebler303 Re: 18x18 Linear Rail Tormach... 02-05-2015, 10:56 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-06-2015, 01:02 AM

LeeWay Re: 18x18 Linear Rail Tormach... 02-06-2015, 01:47 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 05:24 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 06:29 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 06:44 AM

Stigoe Re: 18x18 Linear Rail Tormach... 02-13-2015, 07:04 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 07:47 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 04:16 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2015, 07:06 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-17-2015, 11:50 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-19-2015, 03:30 AM

keebler303 Re: 18x18 Linear Rail Tormach... 02-19-2015, 09:31 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-20-2015, 12:41 AM

keebler303 Re: 18x18 Linear Rail Tormach... 02-23-2015, 10:09 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-25-2015, 05:23 AM

keebler303 Re: 18x18 Linear Rail Tormach... 02-25-2015, 04:32 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-27-2015, 12:23 AM

jsheerin Re: 18x18 Linear Rail Tormach... 02-27-2015, 12:35 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-27-2015, 12:46 AM

jsheerin Re: 18x18 Linear Rail Tormach... 02-27-2015, 01:03 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-27-2015, 03:29 AM

jsheerin Re: 18x18 Linear Rail Tormach... 02-27-2015, 03:44 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-27-2015, 04:35 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-27-2015, 07:08 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 08-30-2015, 10:48 PM

LeeWay Re: 18x18 Linear Rail Tormach... 08-31-2015, 01:24 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 08-31-2015, 03:58 PM

spyderxxx Re: 18x18 Linear Rail Tormach... 09-01-2015, 12:14 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-03-2015, 03:37 AM

steve123 Re: 18x18 Linear Rail Tormach... 09-03-2015, 06:00 AM

phomann Re: 18x18 Linear Rail Tormach... 09-03-2015, 11:33 PM

bhurts Re: 18x18 Linear Rail Tormach... 09-03-2015, 04:09 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-03-2015, 04:59 AM

bhurts Re: 18x18 Linear Rail Tormach... 09-03-2015, 05:24 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-09-2015, 01:19 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-15-2015, 02:57 AM

jsheerin Re: 18x18 Linear Rail Tormach... 09-15-2015, 04:00 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-16-2015, 01:55 PM

LeeWay Re: 18x18 Linear Rail Tormach... 09-16-2015, 02:11 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-16-2015, 04:57 PM

jsheerin Re: 18x18 Linear Rail Tormach... 09-16-2015, 08:14 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 02-13-2016, 06:01 PM

steve123 Re: 18x18 Linear Rail Tormach... 02-13-2016, 07:39 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 08-06-2016, 07:23 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-18-2017, 02:50 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 04-03-2017, 01:38 AM

cjsamples Re: 18x18 Linear Rail Tormach... 01-19-2018, 04:49 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 09-18-2018, 07:43 PM

Buoyen Re: 18x18 Linear Rail Tormach... 09-05-2021, 08:39 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 11-01-2021, 07:24 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 11-18-2021, 03:11 AM

jsheerin Re: 18x18 Linear Rail Tormach... 11-18-2021, 07:25 AM

Halfnutz Re: 18x18 Linear Rail Tormach... 11-18-2021, 10:59 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 11-20-2021, 07:32 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 11-22-2021, 08:15 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-09-2021, 06:04 AM

Halfnutz Re: 18x18 Linear Rail Tormach... 12-09-2021, 11:57 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-16-2021, 04:13 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-18-2021, 12:32 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-01-2022, 05:44 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-06-2023, 06:32 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 03-06-2023, 06:34 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-09-2024, 05:18 AM

RaderSidetrack Re: 18x18 Linear Rail Tormach... 12-11-2024, 09:02 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 12-11-2024, 09:07 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 04-01-2025, 04:09 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 04-02-2025, 12:05 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 04-02-2025, 03:26 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 05-01-2025, 01:36 AM

nateman_doo Re: 18x18 Linear Rail Tormach... 06-22-2025, 06:44 PM

nateman_doo Re: 18x18 Linear Rail Tormach... 07-09-2025, 05:08 AM

Previous Post

Next Post

12-16-2012, 08:52 PM #11
outsider787

View Profile

View Forum Posts

Visit Homepage

Registered
Join Date

Jul 2010

Posts

152
Great work man!

That's some serious amount of aluminum there. Especially the table. How thick is that plate? 2"?

adrian.

Reply With Quote

Quick Navigation Vertical Mill, Lathe Project Log Top

« Previous Thread | Next Thread »

Similar Threads

14x14 Linear Rail Industrial Hobbies Build (Charter Oak Automation)

By nateman_doo in forum Vertical Mill, Lathe Project Log

Replies: 146
Last Post: 03-06-2023, 08:14 PM
Open Rail DIY Linear V Rail System

By kram242 in forum News Announcements

Replies: 0
Last Post: 06-11-2012, 03:33 PM
Linear Bearing vs Linear Rail

By microdot in forum Mechanical Calculations/Engineering Design

Replies: 2
Last Post: 10-27-2009, 04:54 PM
PBC Linear Offers New Profile Rail Linear Guides

By Pacific Bearing in forum News Announcements

Replies: 0
Last Post: 04-30-2009, 09:53 PM
6'x10' cnc build, what linear rail setup to use

By davy182 in forum Linear and Rotary Motion

Replies: 2
Last Post: 04-06-2009, 11:51 PM

Tags for this Thread

down, four, home made, its, keep, linear rails, maybe, saying, since, tormach

Posting Permissions

You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
[VIDEO] code is On
HTML code is On

All times are GMT +1. The time now is 05:50 PM.

Powered by vBulletin® Version 4.2.5
Copyright © 2025 vBulletin Solutions Inc. All rights reserved.