[killrmodz]

Ok, so for my config for running my spindle/huanyanvfd/mach3.
VFD Configs:
PD013 - 8
PD001 - 1
PD002 - 1
PD003 - 400
PD004 - 400
PD005 - 400
PD007 - 20
PD008 - 220
PD009 - 15
PD010 - 8
PD011 - 120
PD014 - 12
PD015 - 12
PD70 - 0
PD72 - 400
PD73 - 120
PD141 - 220
PD142 - 5
PD143 - 2
PD144 - 3000

Mach config:
Basic instructions can be found at machs website/forums, which I followed and wiring at the end of this video https://www.youtube.com/watch?v=6mrneHp-6VI. I just modified my output as I didn't care for reverse.

VFD config:
From BoB - - - - to - - - - VFD Terminals
Analog GND - - - - - - - - ACM bottom
Analog OutPut - - - - - - VI (10v) bottom
Relay for FOR - - - - - - - FOR Top
Relay for REV - - - - - - - REV Top
Logic GND - - - - - - - - - DCM bottom

Let me know if you all have success.

Thanks!

[mactec54]

Ok, so for my config for running my spindle/huanyanvfd/mach3.
VFD Configs:
PD013 - 8
PD001 - 1
PD002 - 1
PD003 - 400
PD004 - 400
PD005 - 400
PD007 - 20
PD008 - 220
PD009 - 15
PD010 - 8
PD011 - 120
PD014 - 12
PD015 - 12
PD70 - 0
PD72 - 400
PD73 - 120
PD141 - 220
PD142 - 5
PD143 - 2
PD144 - 3000

Mach config:
Basic instructions can be found at machs website/forums, which I followed and wiring at the end of this video https://www.youtube.com/watch?v=6mrneHp-6VI. I just modified my output as I didn't care for reverse.

VFD config:
From BoB - - - - to - - - - VFD Terminals
Analog GND - - - - - - - - ACM bottom
Analog OutPut - - - - - - VI (10v) bottom
Relay for FOR - - - - - - - FOR Top
Relay for REV - - - - - - - REV Top
Logic GND - - - - - - - - - DCM bottom

Let me know if you all have success.

Thanks!

With the spindle you have you can not use Reverse if it was engaged you will see lots of Smoke, this should never be activated in your VFD

[killrmodz]

With the spindle you have you can not use Reverse if it was engaged you will see lots of Smoke, this should never be activated in your VFD

I know, why I don't have REV wired up and have pd023 set to 0. So i'm pretty stoked. Thanks all who helped! If there are any questions please ask. Special thanks to Mactec54 and Al The Man!!!

[kolias]

Thanks Eric

If you look at the left of my post you can see that I'm located in Canada

[pianori]

Thanks Eric

If you look at the left of my post you can see that I'm located in Canada

Sorry about that. I made an assumption due to your profile name as It sounds Greek to me. I lived in Greece for some time thus my suspicion. But I was wrong. Well, Canada is just as good as far as distance goes. The only thing is you will have to deal with customs since automated technologies inc is located it the USA. That can potentially increase cost and lead time.

Take care.