[akihiko]

Hi,



Yes, correct. G90 means Absolute mode, so after the execution of the line the work cooordinates will be x=100, y=11 and z=12.
Note that if you executed the same line of code a second time the machine would not move, its already at its commanded destination.

Craig

thanks, that work.

So, craig

i need your best advice & recommendation. building cnc.

These are the item i bought.list

1. 2.2KW Water Cooled Spindle Motor ER20 Kit & 2.2KW 220V Inverter VFD 3HP & 80mm Clamp Mount & 75W Water Pump with 6M Pipe & 14pcs ER20 Collet.

1. UC300ETH Ethernet Motion Controller and 5LPT With UCCNC License. -> But i think need a beakout board/
but which one would be the right one, there two different one.( http://www.shop.cncdrive.com/index.php?productID=946 ) second ( http://www.shop.cncdrive.com/index.php?productID=914 )

But also, i was thinking about Pokeys57CNC-ETH or M16D-Pokeys Motion Motherboard w/Mach4 License File Bundle
im about 70% familiar with Pokeys board and Mach4.

i think both are good interface board.

1. cnc base frame. on ebay(https://www.ebay.com/itm/USA-6040-80...c1f12c|iid%3A1


or just get this one and modified. -> ebay (https://www.ebay.com/itm/6040Z-3-Axi....c100005.m1851,

1. stepper motor kit.
got this kit for $149.99/ it come with beakout board (https://www.ebay.com/itm/Promotion-U...72.m2749.l2649


Let me know what you think?

thanks

[handlewanker]

thanks, that work.

So, craig

i need your best advice & recommendation. building cnc.

These are the item i bought.list

1. 2.2KW Water Cooled Spindle Motor ER20 Kit & 2.2KW 220V Inverter VFD 3HP & 80mm Clamp Mount & 75W Water Pump with 6M Pipe & 14pcs ER20 Collet.

1. UC300ETH Ethernet Motion Controller and 5LPT With UCCNC License. -> But i think need a beakout board/
but which one would be the right one, there two different one.( UCSB single port breakout board without cable - CNCdrive - webshop ) second ( UCBB dual port breakout board without cables - CNCdrive - webshop )

But also, i was thinking about Pokeys57CNC-ETH or M16D-Pokeys Motion Motherboard w/Mach4 License File Bundle
im about 70% familiar with Pokeys board and Mach4.

i think both are good interface board.

1. cnc base frame. on ebay(https://www.ebay.com/itm/USA-6040-80...c1f12c|iid%3A1


or just get this one and modified. -> ebay (https://www.ebay.com/itm/6040Z-3-Axi....c100005.m1851,

1. stepper motor kit.
got this kit for $149.99/ it come with beakout board (https://www.ebay.com/itm/Promotion-U...72.m2749.l2649


Let me know what you think?

thanks

You are going to use a 2.2KW spindle on that tiny 3018 router???.....wow, that is asking lot for the frame to hold together while cutting.....unless I'm mistaken with the MX3 model of the 3018 type of CNC router the gantry frame is only 2020 extrusions?....correct me if I'm wrong.

I've just bought the CNC 3018 basic model from Bangers to mess about with.
Ian.