I have a simple 5 axis positional part. I have attached the some screen shots and the actual mcx5 file. I have the part positioned correctly in that the WCS is at the center of rotation of my rotary and tilt table. I can cut the 45 deg section ok, and it positions correct with a B90 and a C-45. The problem is that I then have another compound angle of 2.199 deg more so it should output a C-47.199 and it also has another 6.061 deg from the B90. So it should output a B96.061 which that is out putting correct. The problem is the C is getting output at -42.801 instead of -47.199. So it is taking into account the extra 2.199 degrees but it is not putting it correctly.
If someone could open up my MCX files, and check everything out and look at the misc values page, and make sure I am not missing something, that would be great.
Here is the code
N102 G20
N104 G0 G17 G40 G80 G90 G94 G98
N106 G0 G28 G91 Z0.
N108 G0 G28 X0. Y0.
N110 ( 3/4 FLAT ENDMILL TOOL - 1 DIA. OFF. - 1 LEN. - 1 DIA. - .75 )
N112 T1 M6
N114 G0 G54 G90 X-4.415 Y8.466 C-45. B90. S1000 M3-<<<<<<<<< this position output is correct
N116 G43 H1 Z5.4906
N118 M8
N120 Z4.0906
N122 G1 Z3.5406 F1.
N124 X-9.7769 F7.
N126 Y7.9495
N128 X-4.415
N130 Y7.433
N132 X-9.7769
N134 Y6.9165
N136 X-4.415
N138 Y6.4
N140 X-9.7769
N142 Y5.8835
N144 X-4.415
N146 Y5.367
N148 X-9.7769
N150 Y4.8505
N152 X-4.415
N154 Y4.334
N156 X-9.7769
N158 Y3.8175
N160 X-4.415
N162 G0 Z3.9906
N164 Z4.0906
N166 Y8.466
N168 G1 Z3.4906 F1.
N170 X-9.7769 F7.
N172 Y7.9495
N174 X-4.415
N176 Y7.433
N178 X-9.7769
N180 Y6.9165
N182 X-4.415
N184 Y6.4
N186 X-9.7769
N188 Y5.8835
N190 X-4.415
N192 Y5.367
N194 X-9.7769
N196 Y4.8505
N198 X-4.415
N200 Y4.334
N202 X-9.7769
N204 Y3.8175
N206 X-4.415
N208 G0 Z5.4906
N210 S713 M3
N212 C-42.801 B96.061-<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<this should read C-47.199
N214 X1.077 Y1.4101
N216 Z.8267
N218 Z.7767
N220 G1 Z0. F6.42
N222 Y-.3345
N224 G2 X-1.0319 Y-.84 I-1.115 J.0001
N226 G1 Y-.0697
N228 X-1.0383 Y.0232
N230 X-1.0539 Y.1058
N232 X-1.077 Y.182
N234 Y1.1994
N236 X1.077 Y1.4101
N238 G0 Z.25
N240 Z.7767
N242 X1.087 Y1.4211
N244 G1 Z0.
N246 Y-.3345
N248 G2 X-1.0419 Y-.8424 I-1.125
N250 G1 Y-.0701
N252 X-1.0482 Y.0219
N254 X-1.0636 Y.1034
N256 X-1.087 Y.1805
N258 Y1.2085
N260 X1.087 Y1.4211
N262 G0 Z.8267
N264 M9
N266 M5
N268 G0 G28 G91 Z0.
N270 G0 G28 X0. Y0.
N272 G28 C0. B0.
N274 M30
Thanks in advance