[Delw]

you also left out 2 line numbers on the bottom too make sure you add those as well
and there is a % after your program number this needs to be before.
told you I was blind, I am seeing this stuff after I replied
also at the end your missing G00 numbers at the end
heres what it should look like
also you have a g54 and a E1 you only need a E1 or a G54 depending on what format your using.
not to be an ass but your program is very sloppy. I will show you how mine is
again I am not trying to be an ass

%
O0002
N10 G91G28Z0
N11 G90G0G54X0.Y0.
N12 M6T4
N13 E1
N13.5G0G40G49G80
N14 S4200M3
N15 G0G43Z.6H4
N16 X12.9375Y-1.011
N17 G98G81X12.9375Y-1.011Z-.077R0.0F10.0
N18 X12.4121
N19 X10.9875
N20 X10.4621
N21 X9.0375
N22 X8.5121
N23 X7.0875
N24 X6.5621
N25 X5.1375
N26 X4.6121
N27 X3.1875
N28 X2.6621
N29 X1.2375
N30 X.7121
N31 X-.7121
N32 X-1.2375
N33 X-2.6621
N34 X-3.1875
N35 X-4.6121
N36 X-5.1375
N37 X-6.5621
N38 X-7.0875
N39 X-8.5121
N40 X-9.0375
N41 X-10.4621
N42 X-10.9875
N43 X-12.4121
N44 X-12.9375
N45 X-13.23Y.53
N46 X-12.12
N47 X-11.28
N48 X-10.17
N49 X-9.33
N50 X-8.22
N51 X-7.38
N52 X-6.27
N53 X-5.43
N54 X-4.32
N55 X-3.48
N56 X-2.37
N57 X-1.53
N58 X-.42
N59 X.42
N60 X1.53
N61 X2.37
N62 X3.48
N63 X4.32
N64 X5.43
N65 X6.27
N66 X7.38
N67 X8.22
N68 X9.33
N69 X10.17
N70 X11.28
N71 X12.12
N72 X13.23
N73 G80G00Z4.
N74 G90G00H0Z0
N75 M0

[rob jerico]

you also left out 2 line numbers on the bottom too make sure you add those as well
and there is a % after your program number this needs to be before.
told you I was blind, I am seeing this stuff after I replied
also at the end your missing G00 numbers at the end
heres what it should look like
also you have a g54 and a E1 you only need a E1 or a G54 depending on what format your using.
not to be an ass but your program is very sloppy. I will show you how mine is
again I am not trying to be an ass

ok i ran the program you modified with mine and it worked, im spotting different size holes and when i canceled the first cancycle with g80 its doing what it was doing before, its now reading the next cancycle and spotting about 5 holes then stops again. can i send anyone my full program to look at? thanks guys